learn Russian will come in handy, but according to the scheme, Don Smith made a conscious mistake and did not show the main circuit on which the inductor works, and large coils are energy consumption and you seem to have noticed it well done.
@dkdyker
9 ай бұрын
Thanks, but I am just experimenting and sometimes it works. Thank you for your reply. We must never give up 🙏
@KamilDomjan
2 жыл бұрын
Great job, wish you good luck
@dkdyker
2 жыл бұрын
Thanks I still use that capacitor:)
@mairisspiks402
4 ай бұрын
Can you please tell, what schottky diodes you used in this experiment?
@dkdyker
4 ай бұрын
HFA25PB60 full wave rectified at 25khz
@mairisspiks402
4 ай бұрын
@@dkdyker thank you.
@mairisspiks402
Ай бұрын
I made the device like you, but it's working a little bit differently. When the spark is working then the power of the motor is falling down. Maybe you have some idea why?
@kdkinen
8 ай бұрын
Great work sir, motors are quite difficult to get running You asked for feedback, i have some questions and ideas: ...Is there a known tesla frequency for capacitor-tune on the output coil center tap to one output leg ? Also did you try bonding the output coil with the ground / spark ? any effect of wire wrapped inside ferrite in the core ? ever try the tesla tower inside the output coil with ferrite ? Did you try spark on opposite from ground on tesla ? soon i will be able to answer these, but thought id ask :)
@dkdyker
8 ай бұрын
Thanks for your feedback back but this was a setup from a longtime ago. If you do get to answer these questions I would like to know if possible:)
@kdkinen
8 ай бұрын
sounds great and absolutely ;) im thinking that this whole left / right hand spin Voltage vs Current... is simply a matter of spinning both at the same time. To Ring-up voltage and Current, rather than 1 or the other out of phase. The caduceus winding does this, however im unsure if it should loop back or exit the other end. Next, have you seen Capindres Double Amazing Joule thief with the "ferrite tube resistor" he calls it ? Seems to energize the cable in a way that seems unusual. anyway im back at it.@@dkdyker
@alocin110
Жыл бұрын
Your audio is very low; hard to understand. Thank you for sharing.
@sterlingbruno5196
Жыл бұрын
How many kw
@serefcalskan5156
2 жыл бұрын
Ellerine saglik
@Warrrenjstephens
2 жыл бұрын
Could you please include wire gauge and number of turns. Very interesting. Try changing the frequency of your ZVS.
@dkdyker
2 жыл бұрын
Why do I need to change the frequency of the ZVS?? How would I do that?
@ВалерийВалерий-я7е
9 ай бұрын
Молодец, додумался индуктор должен работать на контур, а в схеме его нет только обмотка съема .
@dkdyker
9 ай бұрын
Please could you write in English as I don’t understand, thanks 🙏
@serefcalskan5156
2 жыл бұрын
Cok mukemel
@dkdyker
2 жыл бұрын
Can you please translate to English?
@PelletJamie
2 жыл бұрын
I have found that with the bifilar the load is important at drawing the amps through... just like the induction hob at 220v with 3kw of load on it in your other video. The thing I have been interested in is putting a generator on the motor.. A to gauge useful power output and B to be able to effectively recharge the battey and C to make use of the load... because I have found that just physically looping the wires back to the battery gives wierd/undesirable results (probably due to high Freq). I have a more farout suggestion but might save it for another time... great work...
@dkdyker
2 жыл бұрын
Thanks James, curious about your far out suggestions? I don’t have to much free time left so if you have anything please let me know, I could try it maybe 🤔
@PelletJamie
2 жыл бұрын
@@dkdyker Also it is harder to obtain the desired results with a battery input.. the ZVS draws whatever load is put on which kind of negates the "pulling" effect through the coils... it is better to have a constant feed with a DC power supply and then go heavy on the loads post coil.
Пікірлер: 25