Hi. I have this machine. There’s no tone when you press the intercom button. And it cannot ring the home phone when making an intercom call from the unit. But can still open the gate and the home phone can still communicate with the unit and able to open the gate from inside the house. Any suggestions?
@vg-techcalendar9498
Ай бұрын
Most likely you may have a problem with the internal speaker inside the intercom
@Isgostnort
2 жыл бұрын
My 1821-081 must process for this procedure from the beginning till the end, no skip or interrupt. Pressing 0+# is unable to exit the programming mode. The master code is not for the gate opening. Because the last owner set up the master code and the open code as the same. After re-setting the master code, I doubted why the door not opening 😅. It confused me couple hours.
@JamesButler-92648
2 ай бұрын
I have that exact model. its in a DoorKing1812 Classic or is there another number after 1812, like -081? I have that light next to the key and square unit, i cant find the exact model except for this video thanks
@vg-tech-llc
2 ай бұрын
You can find the model number inside on the door. In order to get the door open, you must have the key.
@brandonknuksta8929
Жыл бұрын
I have a 1812-089 this process isn’t working for me. Could you tell me the difference?
@vg-tech-llc
Жыл бұрын
1812-089 is an Access Plus keypad. It has totally different programming.
@michaeljames7036
Жыл бұрын
How do you factory default a doorking 1812 classic. System works but i do not get any beeps from the keypad.
@SoCalBruce
2 ай бұрын
That's my question too.
@SuperOCHomes
2 ай бұрын
@@SoCalBruceDid you find any help? I can flip the master switch open then close and my code programed on 01 opens the gate, ONCE. Then nothing until I go and flip the master switch in and off then any program code works but only once. Feels like a short to me. Any ideas?
@21gonza21
2 жыл бұрын
What if you have 3 gates 3 keypads
@vg-tech-llc
2 жыл бұрын
Door King 1812 has only 2 relay. You can only operate 2 gates.
@NicGilardi1999
10 ай бұрын
How I program my car ?
@vg-tech-llc
10 ай бұрын
You cannot. But you can program your car to a receiver that located inside your gate opener.
@NicGilardi1999
10 ай бұрын
Thank you
@c0ld117
Жыл бұрын
how do you reset the code?
@vg-tech-llc
Жыл бұрын
There is no reset. but you can Delete all codes by.. Press *00 X X X X (Master Code) (beep), then press 9 9 9 9 * (beep) wait till you hear long beeeeeep. and all done.
@johnlieu5
Жыл бұрын
@@vg-tech-llc How do you reset code without master? I bought a house and all they gave me was a TEMP code
@vg-tech-llc
Жыл бұрын
@John Lieu without knowing the master code you cannot.
@JamesButler-92648
2 ай бұрын
@@johnlieu5 i have same situation, with no key. I need to rake the key open or drill it out and replace. what was your solution?
@SoCalBruce
2 ай бұрын
@@JamesButler-92648 You can buy a key. I had to do that when I purchased my house. I bought it from a gate opener installation company. But I have since seen them on ebay.
@Hasblock
Жыл бұрын
How do you get it to play the time after touching each button
@vg-tech-llc
Жыл бұрын
if you wait too long it will time out (after ~30 sec.)
Пікірлер: 24