This was just what I needed. My 04 lost the right side door a couple years ago, which was terrific when we were moving, had to load everything in on the drivers side - well a couple months ago, that one stuck too. That one always required a mighty yank to get it to open, but even that didn't work. I already knew about the plastic pieces breaking, but just kept putting it off and finally got my two sets of the replacement parts - had to go to 5 different Autozone stores to find two sets. Anyway, I followed your instructions to get the panels off and get the doors open which was a real leap forward. Then I got sidetracked two more weeks, and finally tackled the passenger side door this past Friday. I didn't notice that one of the retainers was different from the other three - so you saved me some fooling around there. It was difficult to slide the new parts over the cable insulation. I did all but the bottom one with brute force, that would simply wouldn't budge past about halfway, including the old WD40 trick. To the rescue was my trusty torch cigar lighter. My wife rigged up a socket and ratchet to hold the big end, I pushed with some good pliers on the cable and torched the middle for about 3 seconds and it slipped right on. So I again followed the video to put it back together, not trusting my memory from 2 weeks ago. I am 66 years old after all. I did want to mention - I think somebody else mentioned too, the bolt heads that hold the lower large door panel on were 6mm on my 04, perhaps this was changed. And the single bolt behind the window control panel was 10mm not 8mm. The thing that had me worried after taking it apart was getting to the bottom latch - again I stopped watching the video because I didn't have the parts yet. Never would have guessed that there were three more torx bolts from underneath. So my passenger side door is done and works better than it ever did. The driver side is all apart, but the cable popped out of the latch mechanism so I will need to figure out how to pop the latch without it, or string it back in to manually pull it. At least I know what it looks like now. Once I get that door popped open, it should only take me about an hour to finish the job. I love youtube. I replaced the passenger side front door window regulator on this truck a few years ago thanks to a youtube video, I did the job for $94 including the part. The parts for this latch fix cost $12.99 a set at Autozone once I found them. I also watched a great video on drywall finishing back about 12 years ago. My wife and I finished our garage beautifully, having never done it before. I've seen "pro" jobs that looked much worse. I've always believed never pay anybody to do what I can do myself, and I'll keep being a DIY guy until my arms and legs don't move anymore. Thanks again for the outstanding video!
@noahmartinez1124
3 жыл бұрын
Amazing video, helped me fix my 07 F-150 and only took about an hour. Super easy, simple, highly recommend this wonderful lady
@hopfammedia
3 жыл бұрын
Thanks Noah, so glad we could help! And we agree! We think she's pretty amazing too. 😊
@pastorlugo121
3 жыл бұрын
Outstanding video. This is the best lesson I have seen on this mechanical issue pertaining to a Ford F-150...particularly because the professor has a methodological way of showing you how to open the stuck door and how to replace the broken pieces in a logical way. Not only is she a great mechanic but gorgeous as well. My wife loved the kiddy cats as part the lesson plan. Kudos to you.
@hopfammedia
3 жыл бұрын
Thank you for the kind comment! We try hard to put out great content, and it's so encouraging to hear that we've been a help. And we sure do love our kitty cats!
@abbyrichardson4146
7 ай бұрын
Your video saved me so much time and money - thank you! Both of my doors went out at the same time and I can’t imagine having to pay a body shop to do this. You’re a life saver!
@hopfammedia
7 ай бұрын
You are most welcome @abbyrichardson4146. Thanks for posting!
@jaymedavis7567
2 жыл бұрын
Great video. The cat falling over for some love was adorable, give him/her some scratches. I bought the parts from your affiliate link, and feel confident on doing the replacement. Kudos to the person operating the camera too, really puts this together nicely!
@hopfammedia
2 жыл бұрын
Thank you Jayme, will do! We're unfortunately not an affiliate, but we're glad our link was a help. We'll be sure to pass the word along to Laura and our camerawoman Julie! :)
@AmazingWord23
Жыл бұрын
Great video! As others have mentioned, the 9 latch tork screws are t27, not 25 or 26.. Definitely heat them with a torch (mildly) and they come right out. Also, the plasticoated cable ends that slip into the new pieces need some light sanding/grinding to smooth the indentations from the broken adapters. This makes installing the new ones very easy. The plastic cover just peels slowly away from the door with a little patience - no need to cut it away. Thanks so much for taking the time to create this.
@hopfammedia
Жыл бұрын
Thanks for the input, Norm! Glad you enjoyed the video.
@briancarroll.
Жыл бұрын
This ABSOLUTELY needs to be the top comment!!! The video was well put together, however these tips would have helped immensely.
@winstonbeech3418
3 ай бұрын
I did the opposite... I was able to crank the torx screws off without much trouble, I saved the torch to slide that one last retainer on the bottom cable! I didn't even look at what number torx it was, I just got lucky on the first one I pulled out!
@hopfammedia
3 ай бұрын
@winstonbeech3418 thanks for posting. Very glad you were able to complete this repair!
@robertlockwood3289
2 жыл бұрын
THE VERY BEST VID ON THIS THAT I COULD FIND. THE JOB WENT SMOOTH FOR ME ...THANKS FOR THE CLEAR CAMERA WORK AND AUDIO.
@hopfammedia
2 жыл бұрын
We're glad we could help and congrats on your successful repair! Thanks for watching!
@jameseubanksiii7468
Ай бұрын
Thanks so much for your help!! My doors haven't been working for a few years now and I decided to tackle the job after watching your video over and over. I had purchased the metal pieces separately and had a hard time getting them just right - so I decided to purchase the entire wire piece on Amazon for $ 35.00. I am glad to say it is working and now to my other door which should be easier. Thanks again!!!
@hopfammedia
Ай бұрын
You are Most Welcome @jameseubanksiii7468. Thanks for posting!
@user-be5yv3xq4j
Жыл бұрын
While the video is done well and seems to show how easy and successful using the aluminum grommets can be I had a whole other experience. If you don’t get the tension right in each place where the grommets go it’s not easy getting the grommets back out and making the adjustments to make them work. And my experience was it was almost impossible and I had to give up on this method. I ordered the replacement assembly for each door which runs around $60 for both of them and all you have to do is simply replace them. Easy, effective and no guesswork required with the process. And a lot less work and hassle. So if you want to do like this video shows be prepared as it may not go exactly as planned and there’s an easier but yes a little more costly way but it is worth it to me!
@hopfammedia
Жыл бұрын
You're right, this is a good point! The metal replacement grommets & tension overall can be difficult to adjust. We have a video on this same Ext. cab Rear Door issue using the replacement assembly part you're talking about: kzitem.info/news/bejne/uaGdyaB7jIeXd6A
@frankparker2201
10 күн бұрын
This video was the best one in replacing the cr#p connectors that I saw on KZitem . Thank you fmp47
@hopfammedia
10 күн бұрын
You are most welcome! Thanks for posting.
@rickgish6660
2 жыл бұрын
so, a year or so later, this video is still helping people or at least me. I am very vehicle challenged. I did not want to spend the money going to an auto shop. I have a 2008 F150. Both back doors stopped working at almost the same time. One was completely not working; the other, I had to push in, pull the handle and pull the door. I decided to fix them, bought the same thing you did for the doors. I watched your video and was able to complete the task. However, it took me almost 3 1/2 hours, it took forever for me to get the metal all the on the cable and removing the old stuff from the cable. I had 2 bolts left over, I watched the video again and found where each one went. The one behind the window control. thank you so much for the DIY.
@hopfammedia
2 жыл бұрын
That is awesome Rick!!! So glad our video was helpful, and thanks for watching!
@paulfoster7346
Ай бұрын
Wow you are awesome this is the best one I've ever seen this lady knows what she's doing thank you so much for sharing this I'm amazed thank you😊
@hopfammedia
Ай бұрын
You are most welcome @paulfoster7346. Thanks for the encouragement!
@jaxjax4520
6 ай бұрын
Life saver, thank you.. been procrastinating learning how to do this for a few years.. But I have a son on the way and have 2 months to get this fixed. Have had my truck since 2008 and the half doors stopped working a few years ago. My wife and I never used the back seats other than storage or to move things from one place to another so had no use until now. Much much appreciated!
@hopfammedia
6 ай бұрын
That's great @jaxjax4520. Congratulations on your son! Thanks for posting!
@KrolisMedia
3 жыл бұрын
I had to use the torch method on all the screws because they were all to tight, even for my drill. I ended up burning a little bit of the black sponge on the top, but I was able to get them all out after heating the head. Thanks to whoever it was that suggested this.
@hopfammedia
3 жыл бұрын
So glad you were able to loosen your screws, and thanks for watching!
@thomassmith5546
Жыл бұрын
The best video I have seen for this repair only took me an hour too do both doors.
@hopfammedia
Жыл бұрын
Thanks Thomas, we’re glad we could help!
@terryjoyner4457
4 ай бұрын
I am having a lot of trouble adjusting the tension so the doors will close
@hopfammedia
4 ай бұрын
It is tricky.
@ChuckChamberlin3
2 жыл бұрын
for a year the passenger side rear door could not be opened. The first couple videos i found were intimidating to attempt a DIY repair. So I didn't do anything. two days ago the driver side rear door suddenly would not open. Found this video, ordered the parts and received them today. Following your video was my next step and the first door now WORKS! Thank you for such a well made "how to video". Two items in you video were different for my 2005 F150: 1) The torque for mine was a T27. Trying the T25 first almost worked, but damaged the screw slots. 2) The screw behind the window switch was a 10mm. That was no big deal. Thanks again for a super guide. PS> what happened to your right thumb... noticed the band-aid. lol 😄 👍
@hopfammedia
2 жыл бұрын
Hi Chuck, thanks much for the detailed response. It is interesting to know that there were different screw/bolt sizes used in the manufacturing of these trucks. Re. thumb... always nicking something... I should wear gloves more often!
@luisivan1
2 жыл бұрын
Thank you so much for posting this tutorial. From the parts to get to the step by step details, this video is so helpful and accurate.
@hopfammedia
2 жыл бұрын
We're glad we could help Luis, thanks for watching!
@davidbeal3293
8 ай бұрын
Thank you for this video. I have to do this on my father-in-law's truck over Christmas break. He hasn't been able to open the rear doors in a couple of years. With this video, I was able to order the parts and pack the tools I'll need to take to fix it.
@hopfammedia
8 ай бұрын
Very glad to read your post David! I expect your father-in-law will be quite pleased. Thanks for helping him!
@davidbeal3293
7 ай бұрын
Got my father-in-law's truck doors fixed. He was so happy. They hadn't worked in years and he almost forgot he had rear doors. He is 87 and still driving. Thanks again!@@hopfammedia
@davidjohn5516
2 жыл бұрын
Absolutely Fantastic instructional video! Laura you are a natural mechanic and teacher. Thanks for the help as my 05 finally gave way to this problem. I had no idea how to open the door panels but you made it so easy to understand and accomplish. Great tool tips too!!
@hopfammedia
2 жыл бұрын
We're glad we could help! Thanks for watching David!
@ericawelter6121
3 жыл бұрын
Perfect! We've been looking for a newer model repair video. Thanks!!
@hopfammedia
3 жыл бұрын
We're glad we were able to help! Thanks for watching!
@brianlawson6389
Жыл бұрын
This video was amazing. Gave me step by step instructions to repair both my doors. There are no words to express how grateful I am that you did this video. Thank you.
@hopfammedia
Жыл бұрын
So glad it was helpful to you Brian. Thank you for the encouragement!
@goatfilms6054
3 ай бұрын
You saved the day! This video was perfect for me to fix my 2005 F150! Exactly like you showed in the video. Thank you for taking the time to do this. Really helped out.
@hopfammedia
3 ай бұрын
Thanks for saying thanks @goatfilms6054! Appreciate your post.
@dg8620
Жыл бұрын
Thank you this helped a bunch! Even after fiddling I couldn't get it to reliably open. Sometimes the hinge wouldn't engage. After poking about to understand how it all worked I figured out that there is a physical switch on the door jam. It puts the latch on either side of equilibrium. I.e. prevent the backdoor opening when the front is closed, but letting open when not. I prised this off and there was another of those adjustable tension clips. I set this to raise the rod up a couple of teeth, which fixed my problem. Hope that helps others.
@hopfammedia
Жыл бұрын
Glad we were able to help, and that's great input. Thanks for adding to our community!
@Pro2beDuh
2 жыл бұрын
Thank you so much! I bought a used 06 F-150 Lariat and the back door in the driver side was stuck. After buying the parts in your link and following this video, I’am happy to say it’s FIXED!!! 😁🙏🙌🎉
@hopfammedia
2 жыл бұрын
That is awesome!!! We're glad we could help, and thanks for watching!
@andrewschmidt3974
3 жыл бұрын
Oh man, thanks for showing how the piece for the top latch works at 9:10 . No one else on youtube showed how to get slack out of the center latch!
@hopfammedia
3 жыл бұрын
We're glad we could help! Thanks for watching!
@lauratibbles6598
3 жыл бұрын
Well Laura my name is Laura as well and I’m not afraid to try to tackle something myself I have an 2004 F150 I love my truck and it looked complicated but your video makes it all go so smoothly thank you for sharing and I will be subscribing to you channel by the way I’m 70 but my mind is not
@hopfammedia
3 жыл бұрын
How cool!!! Thank you for subscribing, and we're glad we could help! :)
@BigAlWillis
Жыл бұрын
Its always nice when there is a parts link in the description. Appreciate the video. This will be one of my future projects. Thumbs up
@hopfammedia
Жыл бұрын
Thanks much Jason. We appreciate the feedback!
@scbeachboi
3 жыл бұрын
Thanks 🙏 I have a 04’ 5.4L and eventually probably will have to do this in the future...
@hopfammedia
3 жыл бұрын
You're most welcome, glad you enjoyed the video, and thanks for watching!
@joer7968
3 жыл бұрын
Awesome video, and have looked at others. Admittedly the first door took 2 1/2 hours and many more tools than you! But second was done in 40 mins! Thanks
@hopfammedia
3 жыл бұрын
Thank you @JoMama! We're glad our video was a help! :)
@leeisenberg
11 ай бұрын
Thanks for sharing. Helping my friend w/ this, what a royal pain headache, Mercy. Worked on it several hours last Saturday & several hours again last night, getting closer & closer, but it shouldn't be so difficult. Thanks again for sharing this, very helpful. - take care
@hopfammedia
11 ай бұрын
Your welcome Lee! Thanks for your encouragement.
@BobbyV78
Жыл бұрын
This just happened to 2012 ford f150 stx. Was thinking of taking to mechanic but after watching this great tutorial video… I’m pretty confident I can do it. Thanks
@hopfammedia
Жыл бұрын
That's great Bobby, we're glad we could help! Thanks for watching!
@ThaRealIansanity
4 ай бұрын
Thanks for the detailed explanations. I have to fix both doors on mine. I Just fixed the shifter cable bushing because it's also made of cheap plastic. Glad to see these after market parts are made tougher.
@hopfammedia
4 ай бұрын
Agreed @ThaReallansanity. Thanks for posting!
@williampenrose696
11 ай бұрын
I LOVE that you show ur mistakes.. That's good stuff so we can keep an eye out for those things. Thank you for the video
@hopfammedia
11 ай бұрын
You are most welcome William, thanks for the encouragement!
@steveedwards4635
Жыл бұрын
Thank you for your excellent video! I was able to fix my door in just a couple of hours with your instructions! 🤙🏾👍🏾
@hopfammedia
Жыл бұрын
That's great Steve! Thanks for watching!
@jasons5842
2 жыл бұрын
Other than not using an electric impact to remove all bolts to move things along this was the best video on how to do this type of repair on KZitem.
@hopfammedia
2 жыл бұрын
Thanks Jason! We didn't have that tool in our shop, but it would have been awesome to use one!
@ruthie9669
2 жыл бұрын
Great video! Best video I found. Both my doors don't open. The last time I had my mechanic fix my doors, (2 years ago), one broke again within 3 months. (I think he had one of his other employees do it ) I haven't been back to get my doors fixed. Will purchase the metal ones. Your instruction is great. Thanks.
@hopfammedia
2 жыл бұрын
We're glad to help Ruth! Thanks for watching!
@joshuagates2735
3 жыл бұрын
Excellent tutorial! I watched at least 10 other videos before finding yours. Those were very similar but your presentation and camera work are spot on. Thank you very much and keep up the good work! For those reading, I did run in to one issue. Project Completed On: 2004 F-150 XLT Date: 7-20-2021 Parts: www.amazon.com/gp/product/B01N1G2QUT/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 Tools: As explained in the video Time: 40-45 minutes per door Issue: T25 bolts holding bottom latch stripped out. Resolution: Cut heads off screws using hacksaw. Pulled out latch. Heated bolts up using propane torch. Used vice grips to grab shank of cut bolts.Turned to loosen and remove (was super easy). Ran to Ace Hardware. Purchased M6-12mm 1/2" replacement screws. Fit perfectly. Other than that, it went pretty well. I am not a mechanic at all, but when I got a price quote of $375 per door to fix it, I was like "no freaking way!". Luckily I did a little research, found this video, and did it myself. It seriously is a very easy project and if I can do it, I promise you can too. FIX THOSE DOORS!
@hopfammedia
3 жыл бұрын
That is awesome Joshua, we're glad we were able to help! Thanks for the added and detailed advice!
@tomsnyder5324
Жыл бұрын
Without a doubt, you are the best “explainer/demonstrator” I have ever viewed. VERY clear and helpful with all details. (Sorry, about your right thumb…I wondered if you were going to ‘find’ a sharp edge…hope that wasn’t the case.)
@hopfammedia
Жыл бұрын
Thank you Tom! We think she's wonderful too!
@joshfritts4084
10 ай бұрын
Solid video and tutorial! My '04 passenger side door broke and within 2 weeks the driver side door did too. Just part of being an older truck. Only difference is that on mine, the bolt under the window controller was a 10mm and not an 8mm like stated in the video. Who knows why but no big deal. Thanks for your help.
@hopfammedia
10 ай бұрын
Your most welcome Josh. Thanks for posting!
@patrickford18
3 жыл бұрын
I've done this a few times and its as good a video as I've seen. I would like to point out, a butane torch might be useful in removing the bottom Torx screws, because Ford uses a killer thread locker on them. You'll likely break your #27 Torx bit before breaking them lose. With a few seconds of heat from the torch, they come out easily and the thread locker stays in place for when you put them back in.
@hopfammedia
3 жыл бұрын
Thank you for the good advice Patrick, and thanks for watching!
@KrolisMedia
3 жыл бұрын
I’ll try this. I couldn’t get my screws out and messed up a few of them. Idk what to do about it now.
@AmazingWord23
Жыл бұрын
@@KrolisMedia If you tried the t26 or t25 torx bit by mistake, you might have messed up the screw a little, but with a little torch heat and a t27 bit might still get them out.
@dannyorsello8668
2 жыл бұрын
Well done, very informative. You are a brilliant young lady. My 07 did this to me yesterday and I replaced all of this on my 98 so many years ago I forgot it. Hard to believe Ford gets a way with this.
@hopfammedia
2 жыл бұрын
Thanks Danny, we think she's amazing too! So glad we could help, and thanks for watching!
@levicross4142
2 жыл бұрын
The 9 door screws on my 2007 F-150 were T27 torx. Thanks for the video, it was helpful.
@hopfammedia
2 жыл бұрын
Thank you for the clarification Levi! We are learning as we go, so this is helpful to all of us in this community!
@bp7315
Жыл бұрын
I have a 2007 f150 Supercab and the T27 also fit better for me too.
@FreyaTheMalingata
2 ай бұрын
Great video - thank you! Glad they made a critical component of the doors out of plastic and then engineered it in a way that you have to do the work from the back seat, inside the truck, with the doors closed. Top-notch engineering, eh? Must have hired the Harley-Davidson drop-outs. But the good news is: it's only 100ºF out today, so being stuck in the back seat of my truck having a heat stroke is going to be a party. Really though - great video, thank you! You'll probably cut the time I spend in the back seat of my truck in half and they may not have to send the corner out for me 🤙 I do have a way of turning EVERY project into a complete disaster though, so don't rule anything out!
@hopfammedia
2 ай бұрын
Hilarious @FreyaTheMalibgata! Stay cool, thanks for posting.
@billy10532
3 ай бұрын
Great video, thank you. My doors haven’t been open in years. Finally fixed them today!
@hopfammedia
3 ай бұрын
That's great @billy10532, thanks for posting!
@robertgriggs3520
2 жыл бұрын
Great video - I also have an '06 F-150, and the video was very helpful when I had to fix my rear doors recently!
@hopfammedia
2 жыл бұрын
We're glad we could help! Thanks for watching!
@utubeaf3c0
Жыл бұрын
The sheath on my cabling was slightly serrated (I supposed to hold the original cable ends better) and it made sliding the new ends on the cable a bear - easily the hardest part of the whole process. Had to use a little silicone lube.
@hopfammedia
Жыл бұрын
Thanks for the input Rich, and glad our video was helpful!
@MrStarfighter14
Жыл бұрын
This video is VERY helpful. My rear door latches recently broke. Thank you!!!!!
@hopfammedia
Жыл бұрын
We're glad it was helpful, thanks for watching!
@michaelnixon7616
Жыл бұрын
Thanks for the tutorial. The way you did it was easy to follow. It took me about 2 hours to do it because I was distracted by nosey family members who were trying to see what I was doing and I misplaced 3 of the scews.😅😅😅
@hopfammedia
Жыл бұрын
Great job Michael! Congrats on completing the job with obstacles!
@linemanfx4
Жыл бұрын
Great video! The only things I did different is use a plastic trim tool to remove the panels and squeeze the plastic pieces with pliers. They're so bridle they just crumble. Keeps from accidently cutting the wire. Thanks again for making such a great video.
@hopfammedia
Жыл бұрын
Nice! Plastic trim tools are a great option. Thanks for your encouragement and input!
@ScottsMarineInc-
Жыл бұрын
Best video on this repair. Doing my 2006 this afternoon.
@hopfammedia
Жыл бұрын
Glad we could help, thanks for watching!
@Brett235
3 жыл бұрын
I have to repair my son's door latch at some point and you have made this a more easy job, thanks.
@hopfammedia
3 жыл бұрын
That's awesome! So glad we could help, and thanks for watching!
@tombarton3708
Жыл бұрын
Excellent video, well produced, best by far of the many vids on this topic. Laura is a real pro......and beautiful to boot.
@hopfammedia
Жыл бұрын
Thank you for the encouragement Tom!
@chuckcowherd6726
3 жыл бұрын
Awesome Laura! Both my cables/ doors have failed. I'll get the parts, watch again, and wait for a cool(er) day! Thanks
@hopfammedia
3 жыл бұрын
So glad we were able to help! Thanks for watching!
@rikgriffin9975
3 жыл бұрын
This video is impressive. She does an outstanding job as well as the person videoing. Well done.
@hopfammedia
3 жыл бұрын
Thanks Rik!
@shikimori-sama7315
3 күн бұрын
This was super helpful. About to order the part
@hopfammedia
Күн бұрын
That's great @shikimori-sama7315! Thanks for posting.
@BtsurvLT
2 жыл бұрын
Thank you very much for you video. It was the first to come up for the door problem on my 2004 F150. I bought the parts from you link and was able to follow your video and fix it. 👍🏼👍🏼
@hopfammedia
2 жыл бұрын
We're so glad we could help Lisa, thanks for watching!
@apsuhead
10 ай бұрын
Both my rear doors broke last week on my 2004 F150. Ordered the 8 new pieces and installed them easily watching your video. My only problem is I couldn’t get my tension clip in the right spot so the doors would latch closed and then open easily. I finally put a rubber band under the tension clip and up to behind the clip above it. It makes it latch easily and then open perfectly. Hopefully it lasts. Thanks! It was a pain dropping off the kids at school with the back doors locked
@hopfammedia
10 ай бұрын
You are welcome @apsuhead. Appreciate you posting about your experience. Glad it's working again!
@kmayo45
Жыл бұрын
Great video. I just fixed my truck following your video and it was easy thanks to your video.
@kmayo45
Жыл бұрын
Followed it right down to the bandage on the left thumb. Again Thanks!!!
@hopfammedia
Жыл бұрын
@@kmayo45 That's awesome! Glad we could help, and thanks for watching!
@ericmontgomery8372
Жыл бұрын
Great video. The only hang up I had was the bottom part of the door/wire. The wire came loose (bc that was obviously where the plastic piece broke) so I couldn’t just pull the wire to release it. However, since I was having to replace BOTH doors at the same time, bc they broke within one day of each other, I moved to the other door, took it apart and was able to open it and look at the piece to figure out how to open the 1st door. The tension issue was a PITA as well on one of the doors. Thanks for the lesson!
@hopfammedia
Жыл бұрын
We're glad we could help! Thanks for watching!
@Powerdad50000
11 ай бұрын
Just repaired my door. This video was a big help!
@hopfammedia
11 ай бұрын
Very glad it helped! Thanks for posting.
@sandramontes1042
4 ай бұрын
Nice to see a woman doing this… I’m going to order the parts and do mine this weekend 😊👍🏻
@hopfammedia
4 ай бұрын
It's a family effort. Thanks for the encouragement! Hope you get it fixed soon!
@marywilliams7063
2 жыл бұрын
Thanks for the Video , you did a great job but i still had to watch it many many times, finally successful thanks again. Some of my screws got stripped and had alot of difficulty sliding replacement metal pieces on, didn't slide on as easy as yours. I have 2005 FX4. Now to fix my sunroof & find out why i have this shudder at times.I only have 104,000 miles on it. But thanks to you for a good job!!!!
@hopfammedia
2 жыл бұрын
Thanks Mary, glad we could help! Best wishes to you in your other repairs!
@donaldsmith7592
Жыл бұрын
Appreciate the video big time!! It helped me out a lot and u did u good job explaining it!! Now I’m gonna teach my son how to do it and do it as a small project with me and him!! Your parents did a good job and brought up a handy young lady!! Good job
@hopfammedia
Жыл бұрын
So glad to hear this Donald! We're thrilled that our video was helpful. Best of luck to you and your son on the repair!
@fatbastard1229
6 ай бұрын
One of my 2008 suicide doors failed today. Great video. Parts from Amazon will be here soon. Thanks!
@hopfammedia
6 ай бұрын
Appreciate that feedback. Thanks for posting !
@PhatOne
2 жыл бұрын
Awesome. I found videos that detailed a door with a manual window but obviously that gets me no where. My rear door is as you demonstrated so disassembly was a breeze once I saw this video. Thanks. Great Time Saver !!
@hopfammedia
2 жыл бұрын
We're glad to be of help, thanks for watching!
@richierich6159
Жыл бұрын
This is exactly what I needed to see to properly do this thanks for the help
@hopfammedia
Жыл бұрын
That's fantastic @richierich6159. Really glad to help!
@badboyjuni4429
3 жыл бұрын
Thank you, I watched your video, ordered the kit you put a link to, and fixed my doors, it was really easy, hardest part for me was getting the new parts all the way to the last line on the upper cables. What I ended up doing was doing the one all the way on top while it was off the car and the one in the middle (that clips to the plastic yellow/white thing) was easier to push down all the way after I clipped it back on and bolted it. I got lucky and didn’t have to adjust any cables on my first try, I made sure to put the little rod that is in the yellow/white clip exactly how it was before I removed it, not sure if that helps or makes a difference. Thanks for the video
@hopfammedia
3 жыл бұрын
That is awesome! So glad we were able to help, and thanks for watching!
@badboyjuni4429
3 жыл бұрын
@@hopfammedia I forgot to mention, I used a dremel to sand down the area where the new metal pieces go because it had little ribs on it that made it a real big paint to slide all the way down to the line, thanks again for the video
@marknissenjr5344
3 жыл бұрын
I was wondering about that . Still having trouble with the bottom ones. I will try your technique of using the dremel tool to sand it. Thanks
@dmann1209
2 жыл бұрын
Excellent tutorial and information. My 06 driver's side rear door just took a dump on me a few weeks ago. Thanks!!!
@hopfammedia
2 жыл бұрын
So glad we could help, thanks for watching!
@Starliner428
Жыл бұрын
Excellent job. Thanks for posting.
@hopfammedia
Жыл бұрын
We're glad we could help, thanks for watching!
@eriklucas-moreno8283
2 жыл бұрын
Thank you for a video and the link for the parts. Helping a friend with this issue next week. May God Bless you. 🙏
@hopfammedia
2 жыл бұрын
We're glad to help, thanks for watching!
@chrisknowles4773
2 жыл бұрын
Thank you for this video; it was a great step-by-step aide. Will add that I have a 2004 f150 and a T27 fit screws better than a T25. Replaced on both doors and they are working fine.
@hopfammedia
2 жыл бұрын
Thanks for watching Chris, glad we could help!
@bp7315
Жыл бұрын
I have a 2007 f150 Supercab and the T27 also fit better for me too.
@ronaldclower1530
Жыл бұрын
Girl, you save me such a huge headache! Excellent video. Thank you.
@hopfammedia
Жыл бұрын
So glad we could help, thanks for watching!
@tbdtobedetermined2353
7 ай бұрын
Great video. I would add.....check the aluminum replacement connectors. I had to take a hacksaw/sawzall blade and cut into the opening just a bit, so that the cable is centered in the connector and doesn't bind; causing the cable to get stuck and not slide properly.
@hopfammedia
7 ай бұрын
Appreciate the comments @tbdtobedetermined2353 . Thanks for posting!
@Richard-ry4mx
2 ай бұрын
Great clip. I'm going to try my doors now. THX
@hopfammedia
2 ай бұрын
That's great @Richard-ry4mx! Thanks for posting.
@luketurner3246
Ай бұрын
It works. I just repaired 2 doors while watching
@hopfammedia
Ай бұрын
That's great @luketurner3246. Thanks for posting!
@chakradjuzeus9275
5 ай бұрын
I definitely learned something 😉 Thanks for the video! 🙏
@hopfammedia
5 ай бұрын
Very Glad it helped @chakradjuzeus. You can find us on X.com at @HopFamMedia too if you use that. Thanks for posting!
@Schizobeatz
3 жыл бұрын
Very helpful will be fixing mine asap..lol at the cat falling over! I agree they should have used metal to begin with 😁
@hopfammedia
3 жыл бұрын
Thanks @Schiziobeatz! Glad we were able to help! :)
@Crickethopper
3 жыл бұрын
I love these repair videos! Keep up the good work!🙌🧡
@Ana-n-Mari
Жыл бұрын
Thanks for the video it was so helpful and thanks to you I fixed my car’s door!
@hopfammedia
Жыл бұрын
We're glad our video helped you! Thanks for the encouragement!
@teiks886
28 күн бұрын
For anyone wondering why their T25 won’t work, try using a T27. It fits perfectly for me.
@brianz1f
2 жыл бұрын
Great video. I almost sold my truck because of the back doors not working anymore.....but you are my FEMALE HERO "superwoman" 🦸🏿♀️
@hopfammedia
2 жыл бұрын
So glad we were able to help and that you didn't sell your truck! I'll be sure to let Laura know! :)
@jerryhoward6782
Жыл бұрын
Just the video I needed. Thanks ! My truck door operates probably better than new.
@hopfammedia
Жыл бұрын
Glad we could help, and thanks for watching!
@JaredCoombs-x3f
8 күн бұрын
Thanks so much!!! That was super easy thanks to you!
@hopfammedia
6 күн бұрын
Your welcome @JaredCoombs-x3f!
@joseparral4464
Жыл бұрын
Thank you very much. Your video was a lot of help. You made it simple to follow along and explained everything to perfection.
@g.ramirez7250
3 жыл бұрын
This is exactly what I needed !!! Thank you 🙏
@hopfammedia
3 жыл бұрын
So glad we could help! Thanks for watching!
@michaelholt3721
2 жыл бұрын
Your video really helped me out. I have a 2013 model and my doors are the exact same. Thank you.
@hopfammedia
2 жыл бұрын
So glad we were able to help! Thanks for watching!
@Felix-pf8eb
3 ай бұрын
Thanks you cooperation very special.
@fishnchipsforge
2 жыл бұрын
Awesome video - carefully watched each step and fixed my 2004 doors. I didnt see the comments on the bottom T25 screws and one stripped. I welded a nut to the head and used a wrench to remove. That was annoying, but not the fault of this great video
@hopfammedia
2 жыл бұрын
So glad we could help, thanks for watching!
@bp7315
Жыл бұрын
Great video! However, one possible improvement that worked for me and may work for others is that I found that all 9 of the latch screws actually have T27 Torx heads, (instead of T25), which may explain why some people have stripped the heads when removing.
@johntrishstrange7378
2 жыл бұрын
Your video was spot on! Very good detail and instruction. Made this job a breeze.
@hopfammedia
2 жыл бұрын
We're glad to help! Thanks for watching!
@jimmybarcusdotcom
2 жыл бұрын
Thank you! Great video, easy to understand, I was able to do this in a few minutes! Great instruction!
@hopfammedia
2 жыл бұрын
We're so glad our video was helpful, and thank you for watching!
@christopherdavila8811
Жыл бұрын
Thank you very much for taking the time to create this video. It was a great tutorial and I truly appreciate it!
@hopfammedia
Жыл бұрын
Thank you Christopher! We're glad we could help!
@stevetrowell
Жыл бұрын
What do you call the four metal parts for fixing each door and where can they be ordered? Excellent video!
@hopfammedia
Жыл бұрын
Hi Steve, there is a link in the video description. Click that link and it should take you to the parts you need.
@ronaldhague2504
Жыл бұрын
Thank you very much for this tutorial it still took me my dad and 2 hours but we got it fixed and it was all thanks to you other wise my door would be closed forever lol
@hopfammedia
Жыл бұрын
So glad our video was helpful Ronald! Thanks for watching!
@ASchoppe
2 жыл бұрын
Thanks for the excellent video. She made the repair very simple and plus she is pleasing to the eye. Keep up the good work.
@hopfammedia
2 жыл бұрын
We're glad to help, thanks for watching!
@randybase1
3 ай бұрын
Great vid. Saved me some time.
@hopfammedia
3 ай бұрын
Very glad it was helpful to you @randybase1!
@magdalenogarcia7382
Жыл бұрын
Wooo Señorita for sure you video es de mucha ayuda para mi tengo ese problema en my ford F 150 2000 I'm going to fixed.
@javieroliva5893
2 жыл бұрын
VERY VERY detailed best video out there no questions here
@hopfammedia
2 жыл бұрын
Thanks Javier, we're glad it was helpful!
@manking4249
Жыл бұрын
This video helped a lot and saved me money. Thanks.
@hopfammedia
Жыл бұрын
That's awesome! Glad we could help and thanks for watching!
@Jay388
Жыл бұрын
Mine just broke today 🤬 Thanks for the video, it's a lifesaver!
@hopfammedia
Жыл бұрын
Your welcome Jay! Glad to be a help.
@bobbywillis9065
2 жыл бұрын
Finally got around to fixing mine,thanks for the great video.
@hopfammedia
2 жыл бұрын
That's awesome Bobby, we're glad we could help! Thanks for watching!
@grahlantv2325
7 ай бұрын
Thank you for this video God bless you
@hopfammedia
7 ай бұрын
You are most welcome @grahlantv2325! Thanks for the encouragement.
Пікірлер: 582