This site is excellent for anyone who owns a downrigger!Thanks Mike
@synocate5602
2 жыл бұрын
8:00, solved all my issues, thank you so much
@RFT2112
4 жыл бұрын
How do you replace the line counter on a Cannon Mag 10. Do you have to take the wire sppols off?
@potocket
7 жыл бұрын
Great Job on the video Luke
@mikewhitman3046
4 жыл бұрын
Does the New spool you are showing in the video fit the MAG 20 DT/HS? If so, what is the part number? And if so, does the new spool require 2 magnets? Thanks
@TheGlenn350
3 жыл бұрын
I found a cannon downrigger on the highway about 20 years ago and it has been in my backyard ever since in the weather. My boss is an eBay guy and I was going to get him to sell it for me. After some inspection I found that both of the switches are broken from the hiway and there is some corrosion on the outside of the electric motor. Do you think it is worth repairing or the scrap bin?
@user-go2ux7dp5u
Жыл бұрын
What about the old lake systems riggers? Do y'all repair those or can you point me to a pdf or hard copy manual for them?
@Fish307
Жыл бұрын
Unfortunately there are no parts available and we do not have any pdf or manuals on them sorry.
@ToolManTaylor
3 жыл бұрын
My cannon downrigger keeps blowing the fuse. Rigger comes up slow. (12lbs ball) What might be going on? Also I was wondering if getting grease on the clutch fiber washer will ruin it.
@Fish307
Жыл бұрын
Greese wont ruin the clutch fiber. It sounds like there something inhibiting the free movement of the spool or the motor is bad.
@timtanimura9583
Жыл бұрын
I bought counters for my lake troll works great. but what is the dial for on the swivel head for? thanks
@Fish307
Жыл бұрын
You upgraded your but thats the counter that comes with it.
@jimmunoz6701
6 жыл бұрын
Got my answer, thank you guyes 🤙🏿🤙🏿
@lewiswatchorn7239
3 жыл бұрын
Is the counter serviceable? I have two Mag 10s that are a year old, moderate use, and just had one of the counters skip for the better part of a morning and then started working fine. The spool and counter gears were aligned correctly. I had to re-zero my line with the ball touching the water several times, so I know that wasn't the issue, it was something inside the counter itself. Thx!
@Fish307
Жыл бұрын
Unfortunately it is not serviceable and can only be replaced
@spineguy444
4 жыл бұрын
Would you provide a tear down and service for Walker electric downriggers. I have 2 and they are starting to make a whining noise. Thanks
@spineguy444
4 жыл бұрын
@FISH307 Thanks
@jeanineschmidt4925
4 жыл бұрын
Is this video for the Cannon Magnum 10 STX or a different downrigger? I am attempting to order parts noted in a previous question but want to be sure because the part number noted look different than the parts in the video. TIA
@jeanineschmidt4925
4 жыл бұрын
Thanks for all your assistance. Just ordered the parts from below...
@spineguy444
5 жыл бұрын
What size cable are you using? Thanks
@carlossales8710
5 жыл бұрын
How do I stop my cannon stx10 from blowing fuses when the ball hits the water line
@Fish307
Жыл бұрын
Not sure without taking a closer look. Likely something is wired wrong.
@Wayne-xy6yw
3 жыл бұрын
Is there any chance of you doing a video covering the Cannon Shortstop feature and the different switches ie 3 prong and 4 prong and where each is relevant and can be used Also the possibility of converting a broken Electric model to Manual I have a Marlin HP Electric and I see the fibre washer seems to be covered in grease from the drive shaft gear. Is this normal or has the prior owner overdone the grease application which covers the entire enclosed housing.ie Is the Fibre clutch washer meant to run dry
@sethbrooks4764
3 жыл бұрын
I’m working on a cannon digitroll 5 right now and am shocked the roller gear housing is filled with grease also.. How can a clutch work bathed in grease?!? Did you ever find an answer if this is normal? Special clutch pack or something?
@Wayne-xy6yw
3 жыл бұрын
From memory I did receive a reply in the affirmative but I cant locate it. Anyway I put it all together with the clutch pad all bathed in grease and its working fine so like you I scratch my head. I just used the grease that was there.
@MrBluesman59
Жыл бұрын
How about a video on changing counter, and gears on a mag 10A?
@guyh.4553
5 жыл бұрын
Thanks Luke helping me out. One thing tho is that your info only talks about new riggers. My Mini-Mag 5 has an actual swivel on the boom end attached to a pulley. How do you remove the metal cap in the end of the boom to replace the swivel & pulley? Also is there a way to remove the boom easily? Thx!
@Fish307
Жыл бұрын
The only way to take the pulley off is to unscrew it and take the pulley apart. As far as the boom goes there is a screw on under side of frame remove the screw and the boom will come.out.
@spineguy444
3 жыл бұрын
Is Walker still in business?
@davidgaskins2166
7 жыл бұрын
how to reset the line counter on a cannon lake troll downrigger manuel
@jimmunoz6701
6 жыл бұрын
Yes , how come this question wasn’t addressed?????
@ozman6685
5 жыл бұрын
Disconnect the counter wheels on the downrigger and spin the wheel that counts the depth back to zero. And re engage the wheels 👍
@Journaljunkie47
5 жыл бұрын
What an amazingly informational video by a super hottie.
Пікірлер: 37