important with the sleeve, firstly I'm never doing a false forearm again, but more importantly the top sleeve run needs to curve more before the top. It's too straight in this video. It's better in this post: instagram.com/reel/Ct1ZCFGuqpt/?igshid=MzRlODBiNWFlZA==
@NadoCrowFriend
24 күн бұрын
Thank you, for yet another outstandingly helpful video!
@ArielLothlorien
Жыл бұрын
I love the quality of your videos thank you! I finished my first practice trowsers made of muslin recently your videos made the difference!
@nyani2706
8 ай бұрын
I'm loving how clear and concise you are with these videos. Super educational. I might be missing it in the videos everytime but what exactly are you referring to by "scale"? Thanks.
@caffeinatedtailor
8 ай бұрын
It's just half of the chest measurement here.
@jathonyalexsandra2632
4 ай бұрын
Remember when drafting sleeve, scale is the whole measurement of the arm hole, not the chest measurement anymore. That mistake cost me a whole day trying to figure out haha.
@namelessone3339
6 ай бұрын
Have you considered doing your drafting in these videos with a Sharpie™ pen which would make it easier to see your work? Thanks.
@franciscostephens4046
4 ай бұрын
Hi, im a bit lost at 28:42 what do you mean with "half our cuff meassurement + 2cm"? Since that (acording to the meassurements in the description) would be 43+2cm, but in the video you mark 16cm (14+2)
@caffeinatedtailor
4 ай бұрын
That was a miscommunication on my part. I'm tending towards a standard of 15cm 6" cuff measure. There is no cuff (wrist) measurement in the description, the one you're referring is the total length of half back to the wrist.
@AndrewBatory
11 ай бұрын
Fantastic work. Keep it up - This is a hidden gem!
@superwavvy5133
Жыл бұрын
excellent job keep it up
@jameshumphris6983
3 ай бұрын
Yo, at around 31:10 when drafting the curve of the undersleeve, do you measure starting from the top sleeve measurement or from the top sleeve measurement minus 2?
@caffeinatedtailor
3 ай бұрын
The top sleeve measurement minus 2, that is correct
@jameshumphris6983
3 ай бұрын
Thanks for the timely clarification! Just discovered your channel a few days ago and am finding it so helpful
@josephkewley2502
4 ай бұрын
Do you have a pattern drafting book
@caffeinatedtailor
4 ай бұрын
No, but it's on the agenda. As well as a guidebook for the rest of my content. Issue is I don't have time right now and I don't expect to have time in the immediate future. I'm re-evaluating the situation in September and then march again. So don't hold your breath, unfortunately.
@NadoCrowFriend
24 күн бұрын
When you are drafting, and refer to “1/4 Scale, 1/2 Scale or 1/8 Scale” which length of the body, or pattern, are you referring to?
@caffeinatedtailor
24 күн бұрын
0:39
@NadoCrowFriend
23 күн бұрын
@@caffeinatedtailor thank you!
@collinsadotey1655
Жыл бұрын
I love the way u teach
@franciscostephens4046
5 ай бұрын
If one wanted to make the pockets slanted, how would the drafting process differ?
@caffeinatedtailor
5 ай бұрын
You want to pivot the shape of the pocket from its centre usually. It's much better for the front dart to go through the pocket, rather than to make it shorter. It's basically the same as taking into account any slight slant, but more extreme. The pocket still goes straight down into the jacket.
@franciscostephens4046
5 ай бұрын
@@caffeinatedtailor I see, thanks a lot. Olso, props for the nice metodology, im a short guy and all the other pattern making videos i found use a lot of arbitrary measurements so the pattern "breaks" but didn't have any problem with yours.
@MaximeRold
9 ай бұрын
Thank you for fantastic video! What is the difference between hip and seat measurement?
@caffeinatedtailor
9 ай бұрын
Seat prominence is the widest circumference around the ass, hip is the same for the hips
@MaximeRold
9 ай бұрын
Thank you!
@imsitizonersss6947
10 күн бұрын
how to determine the scale? does 48 is for all measurement?
@caffeinatedtailor
10 күн бұрын
0:39
@imsitizonersss6947
9 күн бұрын
@@caffeinatedtailor thank u, ur vid is really helpful,im a new subscriber, cant wait for ur next vid!😇
@imsitizonersss6947
9 күн бұрын
@@caffeinatedtailor btw i dont really quiet understand the calculation u did on point 32-35,the one u calculate at the back bodice pattern
@caffeinatedtailor
9 күн бұрын
@@imsitizonersss6947 ok, so measure the size that the back pattern is at the waist. Divide the original waist measure taken from the person by 2. Minus the first measure from the second. Add 8 cm (3.1/4") to this new number. Use that to find the sideseam at the waist, from the centre front. Same idea around the seat, but use 5 cm (2"), not 8 cm
@superwavvy5133
Жыл бұрын
quick question what system do you follow or do you have your own that you've kinda just adapted over the time ?
@caffeinatedtailor
Жыл бұрын
Funny, I was asked the same thing earlier. I'm starting to get the impression that UAL had to make it themselves to be metric and simple enough to follow. They don't source it; which I'd expect them to; which does lead me to believe that it's theirs.
@superwavvy5133
Жыл бұрын
@@caffeinatedtailorI’ve mostly worked in the fast fashion side of patternmaking which breaks my heart ngl so traditional tailoring and your channel really helps. if you get the time to make a pdf out of it i’d be willing to buy. Shirts, pants, jacket and vest. Your way of explaining is also pretty nice. Have a great day my caffeinated friend.
@MrMusickey
11 ай бұрын
at 25:25 was the top sleeve measurement 25.7cm or 21.7cm?
@caffeinatedtailor
11 ай бұрын
21.7
@MrMusickey
11 ай бұрын
Is something subtracted from the measurement as it looks like almost 10” on the tape?
@caffeinatedtailor
11 ай бұрын
That should be the seam allowance on the shoulder lines. So I took off 2 cm/ 3/4" from the top sleeve measure since that's what it'll be when the shoulder seam is sewn.
@MrMusickey
11 ай бұрын
Is there seam allowance included?
@caffeinatedtailor
11 ай бұрын
Ah the immortal question. I don't remember whether I said it here, but there is some seam allowance. The neck line, front edge, hems and centre back seam all don't have SA. You have to add inlay to those seams and they are sewn on those lines.
@MrMusickey
11 ай бұрын
@@caffeinatedtailor ah inlays, I see. On the other areas, is it a 1cm allowance?
Пікірлер: 43