That's very useful. Really enjoyed that. A little off-topic, but my dad's name is Russ and he is a woodworker as well. I thought that was pretty cool.
@SimplyWoodenCreations1980
8 жыл бұрын
+Waylight Creations Thanks for watching and commenting...He must be a fantastic woodworker ...:)
@rk7921
6 жыл бұрын
Finally a design that i like, thank you!
@markbaldwin975
8 жыл бұрын
Best pen vise yet and Ive looked at a lot of them.
@SimplyWoodenCreations1980
8 жыл бұрын
+Mark Baldwin ..Thank you Mark...much appreciated.
@TommyGWorkshop
8 жыл бұрын
very nice work on the jig Russ!
@SimplyWoodenCreations1980
8 жыл бұрын
+Tommy G Workshop Thanks Tommy...
@orelygarcia
8 жыл бұрын
Cool Jig Russ. Thumbs up.
@SimplyWoodenCreations1980
8 жыл бұрын
+OG Timbercraft Thanks you and thanks for watching...
@waltnorris8122
5 жыл бұрын
Good jig gonna make it and save several dollars. Thanks again!
@houtjeboom
8 жыл бұрын
That is a great looking jig Russell
@SimplyWoodenCreations1980
8 жыл бұрын
+Houtje Boom - Be Creative Thanks Houtje ...muchas gracias...
@brentweisenborn660
8 жыл бұрын
awesome video as always Russ can't wait for more videos
@SimplyWoodenCreations1980
8 жыл бұрын
+Brent Weisenborn Thank you very much Brent...I am glad you like them...
@brentweisenborn660
8 жыл бұрын
U and Charles Dearing nick ferry and Jay bates are all u tube kings
@kennewby01
3 жыл бұрын
Could you not use your 90 degree plastic guide that you used to make the jig as a jig? :) nice work btw
@johnshaffner1796
8 жыл бұрын
Great jig, Russ! Makes me wish I hadn't jumped and gotten a pen drilling vice from PSI
@SimplyWoodenCreations1980
8 жыл бұрын
+John Shaffner Thanks John...muchas gracias... Just getting into pen turning so I am trying not to break the bank....
@Irwin-Aviation
8 жыл бұрын
Great idea for the jig Russ. I just turned my first pen for the challenge too and It was really fun and addicting. Looking forward to see what you come up with for your pen.
@SimplyWoodenCreations1980
8 жыл бұрын
+Black Widow Woodworks Thanks muchas gracias... It actually was fun once I started...I have to admit I was a little nervous wondering how bad I was going to scew this up...LOL I can see it been addicting also...it's not that hard...
@robertevans6481
8 жыл бұрын
Russ awesome job....
@SimplyWoodenCreations1980
8 жыл бұрын
+Robert Evans Thanks Robert ...muchas gracias...
@ShannonFargo
8 жыл бұрын
Cool beans. My pen turning will begin soon as well. Wanna race? lol
@SimplyWoodenCreations1980
8 жыл бұрын
+Shannon Fargo Thanks Shannon...good luck in pen turning..."Wanna race?" lmbo... need more practice before I enter the "Pen Turning 500"
@walterwinnipeg7350
7 жыл бұрын
Very good video, Russ. I built a similar jig. One comment/observation... Is the location of the drill press bit relative to the pen blank supports designed around a blank that is 3/4" square? The blanks that I use vary in size, especially if I cut them myself from a log or other piece of wood. So, I always mark the top end of the blank for the hole centre, and then adjust the location of the jig on the drill press table so that the drill starts at my marked location. Thanks for sharing your ideas! Walter
@SimplyWoodenCreations1980
7 жыл бұрын
The supports are designed around a blank that is 3/4" square but do to the fact that it is just clamped down you can move it around to adjust to the center of each blank as long as you have two side relatively square.
@kyguyinohio
8 жыл бұрын
The black square that you are using for clamping does it have a specific name? I have never seen that before.
@johnshaffner1796
8 жыл бұрын
+Joseph Poindexter That's an assembly square available from Rockler. Mainly used for cabinet construction, but as you see, is not limited to just that
@SimplyWoodenCreations1980
8 жыл бұрын
+Joseph Poindexter Thanks for watching...it is a Rockler Clamp-It® Assembly Square like John said...www.rockler.com/clamp-it-assembly-square
@mlong5878
7 жыл бұрын
Great idea but can I ask a daft question, what happens when the drill bit reaches the bottom of the blankdoes it not damage the base?
@SimplyWoodenCreations1980
7 жыл бұрын
If you set the depth of the drill press to just go through the pen blank...it will leave a small shallow hole in the base but it doesn't effect anything...I only drill 3/4" square blanks in it.
@TheRussianWoodworker
8 жыл бұрын
Holy Cow this is an awesome idea! Do you mind if I make this jig and share it on my channel?
@SimplyWoodenCreations1980
8 жыл бұрын
+The Russian Woodworker Thanks, no I don't mind...go right ahead.
@TheRussianWoodworker
8 жыл бұрын
+Simply Wooden Creations thank you so much! It's an awesome idea!
@kimshirley7014
7 жыл бұрын
It appears that you could also use this to center drill a round dowel also of varying diameters..
@SimplyWoodenCreations1980
7 жыл бұрын
You most certainly could... thanks for watching...
@pcorlis
8 жыл бұрын
Great jig, Paul / paulsmessyworkshop
@SimplyWoodenCreations1980
8 жыл бұрын
+pcorlis Thanks Paul, much appreciated.
@spencerbrown2594
7 жыл бұрын
Great Video. I was watching Steve Good Atlanta video and followed his recommendation to watch. I am subscribed and set my alert for you. I'll be watching you. What time on Saturdays?
@SimplyWoodenCreations1980
7 жыл бұрын
Thank you for Watching and subbing...Saturdays 8:00 pm EST... right here on this channel. Just look for the live show.
Пікірлер: 40