I've seen so many videos that just say what they're gonna do, show the engine before and then show it done, SOMETIMES they show a few things they take off or do a cut and tell you where they fkt up. Your "bolt by bolt" videos are out-freakin-standing. It's what people are looking for (IMO) when they're diggin' for these videos. Thanks Troop.
@tylerfast5936
2 жыл бұрын
Lmao I know right. You see a video labeled exactly what your looking for and there going on about there personal life story for social media followers.
@twe3zet745
Жыл бұрын
I agree
@JeffRigney
5 жыл бұрын
Tip! wrap your universal (swivel) with a wrap or two of electrical tape so it doesn't "flop" ! or put a piece of heat shrink tape on it.
@saloram990
2 жыл бұрын
thank you
@jamestambone1858
4 жыл бұрын
Do not change anything in your videos,this is exactly the video's I like to watch,I just got my first duramax an your videos are extremely helpful!!
@TruckMaster
4 жыл бұрын
Thanks
@motohead38
6 жыл бұрын
had my turbo clamp break, didn't do any damage to my turbo thank goodness, still having it rebuilt. I took it to my diesel performance place they wanted 3000.00 to replace turbo, i brought it back home, took me 6 hours just to get off all the heat shields, I have a 7.5 lmm 3500hd dually I had the performance shop delete my egr.(blocker plate). and put a tune in about a year ago. well anyhow I got the turbo out, at the shop getting rebuilt 500.00 ordered my billet turbo wheel, will be here monday. also ordered the complete wcfab pipe kit, i figured i saved 2500 doing it myself so i put the money to the kit. cant wait to get it. I told them you were the one that turned me on to them as i watch all your videos very helpful. Keep up the great vids, and next year when we roll on thru to Lakeport, Mi for our vacation maybe we can grab a coffee at a truck stop and ill show off my rig....:). again thank you for the videos helped me out alot. p.s. I hope wcfab gives you a new free pipe for your drivers side. tell them Jeff said you deserve it for all your hard work..
@ronmower3694
5 жыл бұрын
7.5 wat
@KP0117
4 жыл бұрын
Dude you have the Best videos on KZitem... we all love them!!!
@TruckMaster
4 жыл бұрын
Thanks 🙏
@robertrogina5433
5 жыл бұрын
In the process of installing my Y bridge. I did find a couple of bolts that I hate.
@saltysteel3996
5 жыл бұрын
When doing the EGR delete, is a retune required? I have no tuning equipment and I don't know how to tune. So I would have to take it somewhere and pay more money for the tuning, if it's required. Thanks!
@KeithAllenPerformance
2 ай бұрын
Thanks you man for taking the time to show exactly how everything should be taken off and installed. I love seeing videos like these. Before I would have never tackled the EGR delete, but after watching video man I believe I will tackle it! I just ordered the same setup from WC Fab. Thanks man and also Thank You for your service brother
@Gaffneydaniel92
3 ай бұрын
Just another tip after I tackled this recently. A 1/4” flex extension and 1/4”10mm is easier to gain access underneath the turbo mouth and in front of the hard coolant line. With a 3/8 system I couldn’t get access to the nut because of the coolant line. My socket couldn’t fit .
@anonymous4507
5 жыл бұрын
I ‘m a diesel mechanic, and I really do enjoy your videos. Your camera work is awesome. You are very thorough as well. I have a 2006 LBZ that I am going to do this on, so this helped me out a bunch. Thank you. One suggestion, and I am sure someone else in the comments told you too, but always replace o-rings, and gaskets with new. It’s just not worth the headache of getting it all put together, and something leaks because of reusing old shit. When you are installing o-rings use Sil-Glide. It’s a silicone based o-ring lubricant. It really helps to keep from tearing the o-ring. It’s good stuff. Thank you again for all the information you provide.
@LKN4WAR
3 жыл бұрын
Anon ymous thanks for o ring recommend on the lube. 👍
@NextLevelTruth
Жыл бұрын
Interesting, where’s the best place to get new Y bridge gaskets?
@nickmartushev3759
6 жыл бұрын
Really good videos man helps out a lot. Just don't re-use old gaskets/ seals even if they look good replace them with new ones
@TruckMaster
6 жыл бұрын
+jungle juice do you think I should of used rtv?
@nickmartushev3759
6 жыл бұрын
Rtv is fine, I'm just saying with old gaskets or seals there could be hair line fractures in it that u can't see, that's y it's normally best to replace with new ones.
@jkreviea
4 жыл бұрын
Great video. When I worked on the line at Dmax, we used soapy water to lube the tubes with o-rings for installation.
@Wretched2JZ
Жыл бұрын
Wiggled and pulled that intake tube out like a loose tooth! 😂
@nicholaslask9897
6 ай бұрын
Idk how you do this with the cab still on the truck. for a full EGR delete I salute the guys who can keep a sane mind without lifting the cab
@keithautterson9302
Жыл бұрын
I swear I'm right behind you on everything I watched your egr delete video's to delete my egr now I blew out my stock y bridge o rings also and need a real y bridge lol should've watched this video first lol
@avaleemullin23
3 жыл бұрын
Thanks alot man you helped me greatly just got done doing the hsp y bridge in my lbz. It was a pain but your videos helped a lot!
@truckguyjoe
6 жыл бұрын
Great job. Nice detail on the entire process.
@TruckMaster
6 жыл бұрын
+truckguyjoe thanks joe
@anefalaniko4702
Жыл бұрын
When I replaced the CP3 on my truck I replaced the crossover bridge too because it was see better days. I replaced the it with the exact bridge you have and it’s great
@lucasseymour869
6 жыл бұрын
Great job man. Another tip is to loosen the turbo hold down bolts so you can get more room to the back bolts.
@NextLevelTruth
Жыл бұрын
Which bolts are you referring to? So loosen the turbo enough to move it a little? Trying to do all my home work before I dive in.
@lucasseymour869
Жыл бұрын
@@NextLevelTruth Yeah there are I think 3 or 4 bolts that hold down the turbo. Loosen then enough so you can move the turbo a bit. Search for turbo install for the bolts I'm talking about.
@Shortymanful
5 жыл бұрын
I'm going to jail tomorrow
@nou8257
4 жыл бұрын
Well did you go to jail.
@arcticmike11
4 жыл бұрын
Probably still doing time.
@LKN4WAR
3 жыл бұрын
You gonna need more than a Y bridge bro.
@blairc1234567890
Ай бұрын
Great video still 6 years later
@coltoncarpenter3790
6 жыл бұрын
The ybridge that was used has a major flaw. All the air flowing in hits a wall disrupting the flow. Shoulda used the pusher its actually in the shape of a Y.
@donbing3662
2 жыл бұрын
One other thing that should be mentioned. If you're removing your y-bridge and you have a aftermarket turbo that is any bigger than stock you will need to remove it in order to get the top left bolt out of the bridge.
@jamesdean787
6 жыл бұрын
Yes Sir! removing bolts "Stevie Wonder style"! Thank You for your service. God Bless Merry Christmas
@TruckMaster
6 жыл бұрын
+James Dean lol your no joking! Thanks you too
@pr5721
2 жыл бұрын
I spent 2 hours cursing that one back bolt.... With a magnet sitting next to me
@TruckMaster
2 жыл бұрын
That bolt is such a pain
@jakeberg2266
6 жыл бұрын
I want to do an egr delete and a y bridge so what would you recommend for my 2005 lly duramax
@35057
6 жыл бұрын
Tips and tricks for a pita job like this are just gold! Thanks a ton! Looks killer and I’m sure it performs it too.
@TruckMaster
6 жыл бұрын
+Bayer-Z28 thanks brother
@cesarlaso356
6 жыл бұрын
Took me the same time to do my y- bridge. I did mine after attempting your billet wheel install, I decided, I didn't want to do it twice. I also bought the boost leak tester yesterday before watching this video lol. Keep em coming truckmaster. Just a suggestion but have you looked into Cal tracs or traction bars? I get a lot of axle wrap and they are a must for traction. I just did the Merchant auto pump rub kit, my case was just about to get rubbed through by the pump, that would also be a good video. Berny fix is better and cheaper.
@TruckMaster
6 жыл бұрын
+cesar laso thanks for the advice I haven’t put a lot of thought into trac bars or tcase funny how we are thinking alike on the other stuff I hope I have no leaks because when I get on the throttle it still sounds like a woooosshhhh noise in the engine bay not sure if there still is a leak or the new pipe and bridge just make the truck sound better
@longgoneg60
2 жыл бұрын
Thank you for making this. My lbz pass. side gasket on the Y bridge failed(shortly after heater core line drenched hot engine) Using this as a guide to remove mine now to replace the gaskets. I greatly appreciate it man.
@TruckMaster
2 жыл бұрын
Thanks! 👍
@MiguelHernandez-zi4gl
5 жыл бұрын
Truck master you’re the f’n man!!👍
@TruckMaster
5 жыл бұрын
👍
@Wretched2JZ
Жыл бұрын
@22:32 😮 Wow WC Fab 👎🏽👎🏽. The cheap kit at least has a better route design then your over priced kit!!! Now you literally have to remove the pipe in order to change the alternator 😵💫🙈🙈😩. Oh man.. So happy I watched all these videos before making my decisions. I can clearly see why you went HSP Josh! The WC is horrible in many ways!
@Frostytravels
6 жыл бұрын
another great video man.....excellent work
@TruckMaster
6 жыл бұрын
+Frosty 8415 thanks
@raymondsteed4552
6 жыл бұрын
Really enjoy this Channel, have the same truck and your videos are awesome
@brianyetzke5970
6 жыл бұрын
Yes your details definitely help thx
@jesusleon2247
5 жыл бұрын
Love ur videos man ! I just got a duramax and am getting it build !!
@Torqu3d
6 жыл бұрын
Man at this point lets just take the engine out and give it a good deep clean.
@TruckMaster
6 жыл бұрын
+Shootter for real! That thing is nasty
@zanedebuse7109
6 жыл бұрын
This video is going to save me when putting everything back together thanks man
@TruckMaster
6 жыл бұрын
+Zane Debuse no problem
@latunguley
Жыл бұрын
Where was your EGR finger stick????????? Hard to find a video with a finger stick install????
@bradybashon3941
6 жыл бұрын
Nice work man! Another thing to do is take the up pipe off and replace it with a lb7 up pipe or 2" performance up pipes. Or do what I did and cut the egr bellow right at the pipe and weld a peice of metal on it. The egr bellows are known for bursting with plates and also it gives better straight on flow to the turbo for better spool. Just a pointre and heads up!
@TruckMaster
6 жыл бұрын
+Brady Bashon thanks for the idea I guess that will be my next upgrade now
@111silvrbck
4 жыл бұрын
1st off thanks for your service! Appreciate the the detail on install, I have an LLY being upgraded with WCFab Y-bridge kit and piping along with intake! Love all of videos much needed DIY info!👍
@jacksonbruce1498
Жыл бұрын
Will a lbz y bridge kit fit the lly?
@SwimbaitSamurai
4 жыл бұрын
Hey man I love the vids and I have a question. So I have an 05 LLY and I’m looking for the best Egr delete, what do you recommend and should I do the Down pipe at the same time?
@berlinetta350
6 жыл бұрын
Get a LB7 up pipe now and you'll be 100% properly deleted.
@alphaq179
5 жыл бұрын
How long did it take for your Y-bridge kit to come in from wehrli? curious because I just pulled my turbo to rebuild it and I figured at the same time I will do y bridge kit.
@blake4844
4 жыл бұрын
Took mine 3 weeks and it's not doesn't look anything like his
@rockriver15
6 жыл бұрын
Ratchet wrenches are your best friend.
@beaversstumpgrinding3352
4 жыл бұрын
After watching the Y-Bridge video I am wondering what the best order of operations is for my stock lly with 195k. Instead of doing the egr delete and then doing the y-bridge... So I just ordered the s&b mouthpiece and am thinking of ordering the lb7 up pipe. What are your recommendations from there? Thanks for all the great informational videos.
@LKN4WAR
3 жыл бұрын
hunter wayman the lb7 up pipe esp by wcfab seems ideal as you no longer have that third leg where the blocker plate goes. The less shit in these engine compartments the better.
@stephenrockwell5282
6 жыл бұрын
Hey truck master love the install vid had a question. You know anyone with the pusher y bridge? Herd its got better flow than the wcfab but was curious of your opinion
@Midknightdairyllc
5 жыл бұрын
How the heck did you get the one bolt in top left corner.? It hits the turbo and I cannot back it out any more
@voiceofreason4399
5 жыл бұрын
deerhunterfanvp I had the same problem. I have no clue how to get it past the turbo cover
@pjtruesdale16
4 жыл бұрын
Watched this video, went and checked mine and it’s doing the exact same thing. So I’ll be referencing this video again when my new bridge gets here haha
@TruckMaster
4 жыл бұрын
👍
@k.h1365
6 ай бұрын
Hey bud I just bought a mint 05 lly 1 owner. He put a lift pump in it and bypassed the stock filter but left the stock filter and housing. Stupid question I'm a motocross and aircraft/airboat mechanic but will it suck air in through the in let fitting were the stock filter housing is?
@sickboy8831
5 жыл бұрын
just subscribed just bought my first duramax keep up the great work and thank you for your service
@justinandrews5969
5 жыл бұрын
Just wondering what you did with the low pressure fuel line that runs between the turbo and the y bridge b/c the turbo intake will not set all the way down to put the clamp on. I am using the WCfab y bridge. When I bend the line down the intake will go on but the clamps rub the bridge and intake bad.
@f3arful
5 жыл бұрын
I cut both of the lines and heated to hot and bent them in a new direction and ran some hydraulic hose for the new lines and that allows you to have more play. Pain in the ass but it's necessary and works great
@leewilliams5763
Жыл бұрын
I just have one question. If I replace the y bridge and cold side intercooler pipe on my 07 lbz , what effects will it have on my computer? I've heard it'll just cut on the check engine light and I've heard it'll put the truck in "limp mode" .
@ronallens6204
2 жыл бұрын
Let menthink.. 642 bucks for a new y bridge or maybe 10 bucks for a block plate... no brainer for me... i do like the videos for those who can afford it, to see what is possible..
@trevorklein8903
Жыл бұрын
I’ve gotta question for you sir! I’m looking to get a wcfab kit that includes the cheap pipe I ordered when I replaced my Egr. Do they sell that on wcfab?
@jeremiahhoffmann3227
4 жыл бұрын
Hey so I’m doing this right now and my y-bridge won’t come out after I took the bolts and nuts out how would I get it out?
@TruckMaster
4 жыл бұрын
Just keep working at it also I found that using a rubber hammer helps wiggle it loose as well
@jeremiahhoffmann3227
4 жыл бұрын
Truck Master ok what about putting it back in it won’t go down far enough to get the bolts in
@williambilicki3869
Жыл бұрын
hello sorry I'm using my husband account because I know he watches your video I also know you do good things for deserving people my husband has stage 4 cancer he invested all his savings into his dream truck two months later it doesn't run it needs a fuel injection control module that costs $2500 it is putting him in to a depression he is taking about stopping fighting for everything if he can't get his duramax diesel back running maybe you can help him out help get him back to fighting for life and get him out of the depression maybe you have a fuel injection control module for 6.6 duramax diesel 05 3500 silverado thanks for your time
3 жыл бұрын
Mine popped out and snapped my FPR in half. Then I found that the previous owner stripped the T25 torx bolt out bc that's another retarded thing GM did on these trucks. Had to pull then entire high pressure pump bc of a shit y bridge design. Pretty sure GM built the entire truck around that high pressure pump. You need to invest in a M12 ratchet by milwaukee. You'll thank me later.
@williamrussell8707
Жыл бұрын
Also I've had a my truck in shop a bunch of work done to it injectors, egr, and now it has lound high pitch whistle noise coming from middle firewall location, m.a.p. code glow plug code, egr low flow code, any thoughts would be appreciated.
@steveinman3768
Жыл бұрын
Like your videos just wondering what the round tank is on the driver's side with the clear lid. Thanks for all of your helpful advice.
@lawrenceheinz2679
3 жыл бұрын
Taking off my y-bridge...the up left rear bolt behind the metal hose will not come out without cutting the head off. Your video doesn’t show the whole task. How did you get that out. Did you cut it??? Be honest bro.
@rh5549
2 жыл бұрын
I know this is an old video but hoping you can respond, do you know if this would work on an 06 c4500 kodiak, same lbz engine but alot of the pipes and routing is different than a pickup is thanks
@STANGTHECOYOTE
6 жыл бұрын
Up pipes and manifolds next. Worth every penny imo.
@TruckMaster
6 жыл бұрын
+STANGTHECOYOTE very true
@noahthompson9930
2 жыл бұрын
just get the y bridge and mouthpiece welded... way cheaper to do than buying the aftermarket one, I've done it on 2 llys and never had another issue.
@stewartparker741
6 жыл бұрын
I’m a new subscriber. I own a 2007 LBZ dually and I’m currently in school for diesel tech. I really like your videos man almost bought one of the evergreen EGR deletes until i watched this. Step by step process is great enjoy watching these.
@TruckMaster
6 жыл бұрын
+stewartparker741 that’s awesome glad you like them and best of luck in your future career
@Wretched2JZ
Жыл бұрын
Well don’t buy a WC either! It’s over priced for what you get! Not to mention the route it takes directly over the alternator 😂🙈. What were they thinking!
@cjtyler01
2 жыл бұрын
I’m having a problem with my gaskets fitting. The spot for the gasket isn’t deep enough for the stock gaskets and it won’t go all the way in
@williamrussell8707
Жыл бұрын
I've got a 2006 gmc sierra 2500hd 6.6 lbz I need your info. If I delete egr do I need a tuner of some kind and if so what is the best one .
@brandonseabolt3053
9 ай бұрын
Do you have an email to contact you on? I have numerous questions on doing the same thing on a 2016 LML
@carlosgudiel67
6 жыл бұрын
Your truck is amazing man. I’m going to work on mine to get it where it needs to be
@raceboy002
Жыл бұрын
What is that quick connect fitting coming off your oil fill cap for and the silver canister looking part on the driver side of the engine compartment? Does he talk about those in another video?
@codymiller1441
7 күн бұрын
What are the threaded holes in the neck of y bridge and cold pipe for
@NaztyNate
6 жыл бұрын
so if i get the wc fab y bridge kit for my 06, will this completely delete my egr? and then ill just need a tune?
@noname_ZX6R
2 жыл бұрын
i just bought my lbz last week and it had a boost leak when i bought it. i made a boost leak tester myself and tracked the leak down to the y-bridge. the pipe that connects the y-bridge to the cold side pipe had popped out. same exact issue you had actually. your videos help so much man. thank you!
@ant4l-224
2 жыл бұрын
Quick question I bought both and Egr delete kit and the same y bridge in this video before my Egr delete kit get here do I even need it because the red elbow pipe replaced the blue one
@ethanadams4348
6 жыл бұрын
Did you have to reroute the fuel lines in front of the y bridge it won't let my turbo mouth piece all the way down
@f3arful
5 жыл бұрын
I'm doing this job right now and the lines that run in the direction above the y bridge have to be removed and cant be routed too the original location. He didnt include that in the video, which required cutting them short heat bending and now having to mate 5/16 nickle plated copper lining and re routing. No way around it unless you want it too look like a hack job and or fail down the line.
@coltonshipp1200
3 жыл бұрын
Dang are you at Campbell still? I just know I’m going to screw this up on my own 😂
@saloram990
2 жыл бұрын
you the best mr your videos you share we us are the only professional and educational yo give me the security to do it my self we to much confidence thank you very much for your knowledge
@TruckMaster
2 жыл бұрын
Thanks
@bildrrick
6 жыл бұрын
I wish I had seen your video before I did my egr delete on my lly! Every step you described I was shaking my head yes to. Then when you used the flex head to get the lower rear nuts loose I yelled genius! The egr deletes when I did mine reused that faulty gm y bridge so I didn’t change it but now I will! Thanks!
@TruckMaster
6 жыл бұрын
+BildrRick The Eclectic Nomad good luck! You got this
@tater0909
3 жыл бұрын
I’d love to do this to mine. Just not sure I wanna tackle it
@MrBULLRIDER13
2 жыл бұрын
A thought for anyone on a budget like me I heard taking the stock y bridge out and welding it then reinstall it would work. Is this true.
@yt_nickgage1542
Жыл бұрын
Like he doesnt explain or show how to actually take bridge off
@meatnutbjj9180
5 жыл бұрын
Hey, thank you so much for taking the time to show your work. It would help as my full wehrli kit comes this week. Quick question, in I am replacing both up pipes, and the down pipe would you recommend just taking the turbo out?
@TruckMaster
5 жыл бұрын
Yes it would make it much easier for the ybridge Install but if it’s just up pipes then keep the turbo in the engine
@guuguguguggug
6 жыл бұрын
Awesome video good job!
@markherron69
6 жыл бұрын
Excellent video! Does this y bridge also take the place of the egr delete or do I still need to purchase that? Sorry if I am asking the same question that someone else may have already asked. Keep up the good work! Thanks!
@TruckMaster
6 жыл бұрын
+markherron69 thanks and yes this will replace the Egr
@vinnyd822
Жыл бұрын
How did you connect to the Inter cooler? I have a hsp kit and the elbow that comes off the inter cooler is too long to connect the new intake pipe
@freetoride003
2 жыл бұрын
Your getting no torque on those nuts and bolts. Every single one you used all those extensions you used dropped the torque not even close
@rogermatheny5512
2 жыл бұрын
The duramax must be the most over plumbed engine in history
@NextLevelTruth
Жыл бұрын
Whoa! What is that pump thing screwed into your oil cap?!
@supermo26
3 ай бұрын
Are you still in, or have you gotten out yet? What is your job in the Army?
@jeffconrad6444
Жыл бұрын
if you are putting nuts or bolts back in a tight spot, use a piece of paper in socket !!!!
@lancetrujillo3155
5 жыл бұрын
Thank you for the video, super helpful. Happy Memorial day and thank you for your service!
@TruckMaster
5 жыл бұрын
Thanks
@bassdaze
5 жыл бұрын
been watching here and there from probably one of your first vids where you installed egr delete kit... man those truly are junk, I have ine and had to replace o rings and have my kit pretty much zip tied to help secure it better...anyone with delete kit wishes they did the Y bridge instead, i know i do !! probably do mine next spring as im sure i have boost leak for sure there, take care
@ozziecrosby2092
5 жыл бұрын
Same here.
@that11gmc36
3 жыл бұрын
If I get a egr delete pipe since my trucks efi live will I need to do more programming.
@patrogers8912
6 жыл бұрын
For someone not familiar with duramax you wouldn’t be doing this as your first job Still was a lot of brackets harnesses cooling lines to remove but explained so a novice like me could follow
@f3arful
5 жыл бұрын
I'm doing this job and never have worked on a duramax before. Do you presume it too be that difficult?
@ryansolitro8315
4 жыл бұрын
So the y bridge kit deletes the egr??
@TruckMaster
4 жыл бұрын
Yes
@ryansolitro8315
4 жыл бұрын
Truck Master do I need any other parts like blocker plates or anything?? Thanks for the response!!
@NaztyNate
6 жыл бұрын
does the sensor go back on the y bridge or does the hole get plugged?
@BBR_Voiles89
5 жыл бұрын
Really well made video, I'm not mechanically inclined in the slightest and I want to change that and you've inspired me and provided a lot of learning material I appreciate what you're doing
@kristopherdardeman8286
5 жыл бұрын
101st ;)
@larrydavalos7725
2 жыл бұрын
Hey man how do you get your truck to pass smog with doing a egr delete?
@dieseladdictions4954
5 жыл бұрын
This is what happens when you buy a piece of shit egr delete elbow
@jerrywooton2043
6 жыл бұрын
Why didn’t u clean out where the y bridge bolted down it looked very nasty in there
@TruckMaster
6 жыл бұрын
+Jerry Wooton your right I really should have done that
Пікірлер: 507