Can’t buy an eye but fingers grow back had me rolling 😂
@abrahamsofer2151
4 ай бұрын
Thank you. I don’t currently own this tool. But I used a drill bit to make a few holes in the plastic till it broke down.
@z96M2YUq
11 ай бұрын
Excellent!! I have been struggling with these plastic nuts for hours. Never thought of cutting it off. Love your video; all others on youtube make it seem SO simple. It is usually not!
@tonydelbert1358
8 ай бұрын
Glad it helped!
@HeliusSlayer
Ай бұрын
This is still the most legit way to remove these god forsaken plastic nuts. Thanks for sharing.
@mskatina00
4 ай бұрын
It worked!! I can’t thank you enough. I was stumped for hours. You know what you’re doing. Thanks again ❤❤❤
@neonmaus
8 ай бұрын
You are the man! I just bought a multitool for another purpose and it got its first use on this plastic! For those of you with little room to reach all both sides of the plastic nuts from underneath, you can also cut the plastic tubes off from above the sink. I had to basically cut the two plastic tubes that the plastic was attached to and the tubes (along with the plastic nuts) broke off together.
@chancefitzgerald7740
9 ай бұрын
Thanks, you just saved me my afternoon. I took 3 minutes, clever.
@memesupreme4338
18 күн бұрын
This is going to salvage my Saturday I had already admitted defeat to. Thank you so much!
@zacharylocks
11 ай бұрын
This worked great. Thanks for sharing, love these multi tools
@missanabananazzz
Жыл бұрын
Wish I would have looked up videos before wasting an hour and a half trying to get that dang thing off! Got it off in seconds with that tool! Thanks for posting!
@tonydelbert1358
Жыл бұрын
Glad it worked out!
@johnnyBrwn
8 ай бұрын
You're a genius man. True American hero!
@NESADDICT
4 ай бұрын
Amazing idea! I didn’t even have to cut it all the way off! I noticed it moved when I made the first mark in it and could just unscrew it once the pressure was released.
@rachellease7620
6 сағат бұрын
for those who dont have this tool... i realized after this video, brute force was necessary. a flathead and a hammer worked for me.
@davidruiz5383
Жыл бұрын
Great video, I had same problem; I use similar tool that first try, plastic nuts were damage. First I tried use my Dremel with a disc and it work but use the extension shaft with disc ,was the answer. Again thanks for your video.
@jesuschristislord3512
Жыл бұрын
Thank you for this I’ve been stuck for like 3 days man. So thanks for this video
@tonydelbert1358
Жыл бұрын
Welcome!
@prestocalypsenow
7 ай бұрын
Absolutely brilliant. Thank you
@williamchupin4842
Жыл бұрын
great video thanks for your help if it wasnt for you i wouldnt have had been able to take it out luckily i had an oscillating tool near by
@Kaceythedon
25 күн бұрын
Here 5 days into a tough faucet change, ripped sink off the cabinet and have it face down on floor, flat head and hammer to those plastic things. THANK YOU.
@momeloleather4827
3 ай бұрын
Thanks for taking the time to make this video. I ended up using the same power tool because there was no way I was getting them off any other way.👉👈👍👾 subscribed ✅
@terrelldorsey7945
22 күн бұрын
Thanks for the video. The same thing happened to me, and I had to saw it off as well. Thanks buddy.
@user-fx6cu9wj6g
4 ай бұрын
Awesome solution! Many thanks!
@billaloha6221
Жыл бұрын
Way easier than drilling holes, thanks.
@derrickspencer6456
10 ай бұрын
You sir are a freaking genius!
@tonydelbert1358
10 ай бұрын
Let's not get carried away now 🤣
@jessicagarcia3522
2 ай бұрын
Thank you so much! I’m glad I found your video!!!
@ArBhie_0431
5 ай бұрын
Awesome! Thanks for the idea!
@paulmememan508
11 ай бұрын
I think those plastic nuts are a conspiracy by Big Basin Wrench to sell us useless basin wrenches. Tried to change my bathroom faucet. After fighting with those nuts I find out I need a basin wrench. I buy a basin wrench thinking my problems were solved. Nope, after fighting each nut for hours all I managed to do was break the wings off. Resorted to a dremel though even that isn't ideal given the space constraints.
@slumy8195
2 ай бұрын
this is living hell. Dont have a small cutter tool and these basin wrenches are useless
@paulmememan508
2 ай бұрын
@@slumy8195 I'll always have a scar on my hand to remind me of the first time I tangled with plumbing 😂
@josephteeple773
3 ай бұрын
We wasted hours listening to other fixes. The oscillator saw worked fast. No damage. Thanks.
@dannosoar2534
5 ай бұрын
Thank You Very Much!!!
@lalaatppe8851
23 күн бұрын
Thank you for this.
@mcchuggernaut9378
Ай бұрын
After endless frustration, 2 minutes with a Dremel tool and a carving bit took the damn stubborn nightmares of a plumbing problem right off.
@danielrussell9416
7 ай бұрын
Brilliant. I have the threads on my faucet soaking in penetrant right now. I will use this as a last resort.
@Dani4True
8 ай бұрын
Same here. Thinking about trying pvc pipe cutters or something.
@billdean7500
22 күн бұрын
Nice one mate!
@liv4music
7 ай бұрын
I recently encountered this problem and used a hole saw on my cordless drill. Put the pipe right inside the saw and drilled until the plastic flange was separated from the threaded plastic part. Lifted the faucet and knobs right off from the top. Took 90 seconds.
@tonydelbert1358
4 ай бұрын
That's a good idea as well! As long as you have a deep holesaw bit!
@MissRem
6 ай бұрын
Thank you!!!!
@kachmantv6559
Жыл бұрын
My situation exactly. I bought a Rigid EZ change faucet tool, but it just bent the fins as shown. I guess I need to buy one of those Milwaukees tomorrow.
@tonydelbert1358
Жыл бұрын
There are far cheaper oscillating multi tools then this one. Every tool brand makes them, but I consider the M12 milwaukee fuel one the best you can get. M18 is too big and overpowers small jobs. M12 is nice and light, lowest vibration of any of them in your hand. With the small batteries you can get in some pretty tight spots
@1djgoody
Жыл бұрын
Thank you!
@tonydelbert1358
Жыл бұрын
You're welcome
@Por_981
Ай бұрын
Luckily, I was able to use the RIDGID 57003 EZ Change Faucet Tool to get the nuts off. I also went ahead and replaced the supply lines while I was at it. I installed a Pfister faucet kit that included a push and seal drain assembly. We'll see how long the push and seal function lasts.
@maggietaylor3862
4 күн бұрын
Best video ever
@jasonmanahan6188
4 ай бұрын
Just did this proj earlier and wish i had a cutter.. i basically chiseled ea side of nut with a scraper and small hammer lolol and yes took about 2 1/2 hrs. 2nd nut was even harder than the first. I did think of drilling into ea end but didnt want to pierce my sink. I had the rigid version of nut tool, but once you snap those four sides, you improvise. Awesome vid, def will invest in an oscillator for future projects.
@tonydelbert1358
4 ай бұрын
Think of it like this, if your labor rate was $75hr, you'd be farther ahead to buy an OMT!
@jasonmanahan6188
4 ай бұрын
@@tonydelbert1358 true, am in logistics now but been doin all these hvac stuff around house, its an interesting field to get into.
@timrogers6024
8 ай бұрын
Winner winner chicken dinner !!! Whooo - so worked and I have a new power tool !
@RelearnMath
24 күн бұрын
What is the tool called?
@frankgrimes1385
Жыл бұрын
My 1st thought when I changed mine was you can’t be tight if it’s liquid. Then thought wood and fire wasn’t such a good idea . Was great excuse for a new tool !!!
@tonydelbert1358
Жыл бұрын
I find a use for mine literally every day! They're super handy
@2jacksplat
4 ай бұрын
A wood chisel also works, just need to be careful with fragile sink material.
@kchan4621
7 ай бұрын
What’s the first thing you used? That blue thing? I want to try that first and if not I’ll just buy that saw thingy
@tonydelbert1358
7 ай бұрын
Faucet change out tool. They are also useful for tightening supply hoses and such. interchangeable/reversible ends for different sizes. Sorry for the late reply and good luck! Here's a link to the one I have, but I'm sure there's many different brands, they're all probably close to the same. www.lowes.com/pd/Kobalt-Faucet-Change-Out-Tool/1002797772
@jeromereeves3604
Ай бұрын
Angle Grinder on the top side Metal Max diamond blade
@greytimberwolf68
2 ай бұрын
Yep this is what im dealing with now.... lucky i already have an oscillating tool.
@josetrujillo9906
3 ай бұрын
I heat up a long old flat head screw driver from harbor freight and melt it in half.
@augustusanderson6949
Жыл бұрын
Thanks for the tip, was having the same problem lucky I had the same tool, cut that sh💩 t out quick.
@tonydelbert1358
Жыл бұрын
Glad it worked out for ya!
@networkg
Ай бұрын
I had the same idea, just not the right tool. Going to try a drill and if that doesn't work, its off to Harbor Freight... ah I mean Home Depot.
@salb714
Жыл бұрын
I don't have that tool hmm. What to do.
@tonydelbert1358
Жыл бұрын
Get one lol
@elliemay7787
8 ай бұрын
😂fingers grow back😂😂😂😂
@Willa4420
Жыл бұрын
Try wd 40 or Liquid Wrench
@jabhatta
4 ай бұрын
this costs 200 dollars itself. most home-owners wont have this. can i use a drill with bits instead ? the same bits used to go into a dry wall for example.
@tonydelbert1358
4 ай бұрын
Well, I'm not just a home owner, so my tools are professional quality. If you want a nice one you've got to pay to play. However, if you want one at a throwaway price, harbor freight sells one for $16.99. www.harborfreight.com/2-amp-variable-speed-oscillating-multi-tool-57808.html?ccdenc=eyJjb2RlIjoiOTYxMzY4MjUiLCJza3UiOiI1NzgwOCIsImlzIjoiMTYuOTkifQ%3D%3D&campaignid=19231709222&adsetid=141253622861&product=57808&store=3427&gad_source=1&gclid=Cj0KCQjwk6SwBhDPARIsAJ59GwdXwuoL_XNJAqyewh3w9sem2bC_Zno9P5QK4r1FgLgXARlzzlgcrwkaAsPrEALw_wcB
@jabhatta
4 ай бұрын
@@tonydelbert1358 thanks so much. Just wondering - i have a 8 volt drill with drill bits. Do you recommend a drill with bits for breaking through the plastic ?
@yashaunaswan6248
Жыл бұрын
What is the name of the tool?
@tonydelbert1358
Жыл бұрын
It's an "oscillating multi tool". One of the best inventions ever, incredibly useful!
@yashaunaswan6248
Жыл бұрын
@@tonydelbert1358 thank you!
@panichidaniels346
Жыл бұрын
the saw?
@sede5111
8 ай бұрын
"Fingers grow back"??
@christiannunes6537
4 ай бұрын
Another tip... If you dont got fancy tools like me, just use a hammer and chizzel to cut it off 👍
@tonydelbert1358
4 ай бұрын
220, 221.... Whatever it takes!
@rp9674
2 ай бұрын
What sick F designs this S, diabolical
@jrm255
4 ай бұрын
I bought one of those kobolt tools only mine was a ridgid. Waste of money. Ended up taking the sink top off.
@veracoggins2694
Ай бұрын
😂😂😂 when all else fails cut it off lol 🫡 assignment understood. Having the same freaking problem cussing the heck out of whoever installed my kitchen sink for the last hour and have seen this tool used twice now for sink issues guess that means another investment for this girl
Пікірлер: 83