Hey following you since a while. Started infusion by myself and i'm very excited about this topic. Can you tell me which vacuumpumps youre using? Saw in your oven built video that youre running 2 in parallel. Is this still your current setup?
@dustin910721
9 ай бұрын
This channel teach me so much 🎉 and the content is tailored to exactly what I need. Thanks a lot
@Mortimusmoose
11 ай бұрын
The good old front diffuser. Not sure why people dont do this more.
@KenOs1109
11 ай бұрын
Yep.... saved for later for when my parts arrive. 👍
@Fignewton117
Жыл бұрын
Have you tried vortex generators on the trailing edge of the roofline? Saw a company that makes them and says they work but I don't see any numbers to back it up.
@michaelblacktree
Жыл бұрын
I think he did that in one of the wind tunnel videos.
@Fignewton117
Жыл бұрын
@michaelblacktree ok I will have to go check them out
@markcray5164
11 ай бұрын
One of his more recent wind tunnel vids was on them, not needed on anything except really steep rear screens, depending on whether using a wing or not. Worth another watch if AJ can post a link.
@ajhartmanaero
11 ай бұрын
Yeah we tried some on an E36, the Subaru, and several versions on the yellow mustang and not once did we get a positive result. They are all in the videos on my wind funnel playlist.
@neversettle7666
11 ай бұрын
Per OP response, this is also backed up here. I believe the theory is to assist with activating the rear wing, however effecacy is minimal to nill from what I have seen. kzitem.info/news/bejne/z6yv14uVmqh4p4Ysi=vVZFHazrd0cNLFee
@dorifto
Жыл бұрын
Is there a link to where to get that black closed cell foam?
@Whiterqbbit
10 ай бұрын
I want to do this on a street car that may see track once or twice a year... lips are whack, splitters are life
@rickden8362
2 ай бұрын
With a 1/2'' thick splitter, you could rout out the area around the cut out and then have a flush mount for the tunnels. You might need to increase the size of the tunnel perimeter flange, but that's no biggie.
@jeanfrancoispoivre4438
Жыл бұрын
Magnifique les écopes en carbone 😊
@ManuelGonzalez-mf5tb
9 ай бұрын
I Need a trunk lid and hood made for my 63 chevy impala. Where can I contact you guys. im In so cal
@staycalm4952
11 ай бұрын
Do u have a video how to make a mold for hood or something?
@DruNicholsMD
11 ай бұрын
What type of foam core are you using?
@CJ5EVOLUTION
Жыл бұрын
You guys can make bottom car kits working out of a 3D scan cad model? This means without having the car at your place.
@ajhartmanaero
11 ай бұрын
Potentially.
@Section501K
11 ай бұрын
Cool stuff, thanks
@jpluim97
Жыл бұрын
Like the video. Question for you, the front on my car is kind of short, can the splitter tunnels be cut down a bit if there two long on my car? I under stand that they would lose some performance being shorter.
@ajhartmanaero
11 ай бұрын
Absolutely. 80% of a tunnel is better than no tunnel.
@prestonedmonds4128
10 ай бұрын
What exactly do the tunnels do?
@ajhartmanaero
10 ай бұрын
Make downforce
@FZCarbon
11 ай бұрын
Hiiii bud, do you keep your vacuum pump running 24H until resin cure?
@ajhartmanaero
11 ай бұрын
Only until the epoxy sets.
@FZCarbon
11 ай бұрын
@@ajhartmanaerothx a lot bud, appreciate it.
@po917k
Жыл бұрын
Cool video, as usual. Forgive me if you've already covered this, but have any vehicles with splitter tunnels added had the front downforce improvements measured?
@ajhartmanaero
Жыл бұрын
Yes. We have cfd on our tunnels along with having run cars in the wind tunnel with them.
@mikelmarion
3 ай бұрын
@@ajhartmanaerowould this work on a Lexus Ls430?
@ajhartmanaero
3 ай бұрын
@@mikelmarion yes
@mikelmarion
3 ай бұрын
@@ajhartmanaero ooooo interesting…..Also…have you seen the diffuser on the new Bugatti? They have some technical drawings online. You might find it interesting. Wonder if it can be applied to other road cars
Пікірлер: 34