Gm changed from a flared fitting to an o-ring fitting on the power steering lines some time in the early 80's. You can use a stock 1986 power steering hose without an adapter, and it will work just fine.
@UglyTruckExperience
Жыл бұрын
Thanks Clayton. I will make a point to mention that in a up and coming video. We appreciate you watching and commenting.
@lubblegarage
2 жыл бұрын
Another great tip and trick. Such great info. Let's get these fine folks to a million! They deserve it!
@UglyTruckExperience
2 жыл бұрын
Thanks for watching! We'll get there someday! 😁🤞
@maxsavage4295
Жыл бұрын
You are very helpful! I have been struggling to get power steering on my LS swapped 74, driving with manual steering is a pain, now i can look forward to having power steering! Thanks a million! :D
@UglyTruckExperience
Жыл бұрын
Thanks Max! That's so awesome! We appreciate you tuning in!
@LC-fl3zm
Жыл бұрын
Love the LS SWAP VIDEOS
@UglyTruckExperience
Жыл бұрын
Thanks! We appreciate you watching! 👋
@shoppingcartmafia1482
Жыл бұрын
Seriously appreciate y’all’s channel
@UglyTruckExperience
Жыл бұрын
We appreciate you watching our stuff!
@bowtiebuilding
10 ай бұрын
I’m definitely watching all these swap how to videos and probably rewatch when it comes time! I wish you had a hydro last swap. I’ve got one in the shed and my plan is to put it on the 84
@UglyTruckExperience
10 ай бұрын
I am thinking about putting one on my 74 k10 and would absolutely do a video. Thanks Bowtie. Jerry
@billthompson7579
2 жыл бұрын
Another great video. Looking forward to the next one. Radiators and fan set ups can be tricky.
@UglyTruckExperience
2 жыл бұрын
Thanks for watching! The radiator video is coming up very soon! 😁
@philly_bgaming9167
2 жыл бұрын
Perfect, thank you for the great video!
@UglyTruckExperience
2 жыл бұрын
Hope it helps! Thanks for watching! 😁
@larrybibbey9651
Жыл бұрын
Hi guys, I'm in love watching you do the swap on the LS. I know that this trick work for me a few times. I don't know if it'll work for you but, but I take him the pressure regulator out of an old pump like I have a 68 Camaro and used it in a new modern pump, it worked for me. That way you don't have to use the adapter from summit. I don't know if it'll work for you. I can't hurt the check. If you look for it yourself it's a thought. Thanks again.
@UglyTruckExperience
Жыл бұрын
I will check that out. We have 86 here that I will try. It makes sense though. Thanks.
@DE-ok4ld
Жыл бұрын
Thanks for the video, your timing couldn't be better as I am in the middle of my LS swap.
@UglyTruckExperience
Жыл бұрын
We appreciate you tuning in!
@phillipa7595
Жыл бұрын
My goodness, I finally found out why my pump whines..changing that return line around tomorrow. Lol thank you sir.
@UglyTruckExperience
Жыл бұрын
That's great Phillip. Let us know how it goes. We appreciate you watching.
@throttlewatch4614
2 жыл бұрын
Excellent information
@UglyTruckExperience
2 жыл бұрын
Thanks for watching! 👋
@Brodrdude97
Жыл бұрын
Omg this helpped so much i killed my pump, i ran the return on the top one
@UglyTruckExperience
Жыл бұрын
Glad that it helped. We appreciate you watching. Thanks Jerry and Emily
@brandonarnold582
Жыл бұрын
I might be mistaken, but when I looked for this, the part number was CLP, not CPP, on Summit. Great video. You saved me money and headache.
@UglyTruckExperience
Жыл бұрын
Thanks Brandon! CPP is the manufacturer, and Summit adds CLP at the beginning for some reason, but either one should get you the right parts. We appreciate you tuning in!
@geebopbaluba1591
2 жыл бұрын
Good job
@UglyTruckExperience
2 жыл бұрын
Thanks for watching! 👍
@Mrisra69
5 ай бұрын
Thank you for your video Just became a subscriber here Thank you
@UglyTruckExperience
5 ай бұрын
Glad it was helpful! We appreciate you watching and subscribing! --Emily and Jerry
@MinnesotaisRust
2 жыл бұрын
Slick way to persuade the tube for more clearance.
@UglyTruckExperience
2 жыл бұрын
That dead blow hammer is well versed in the art of persuasion! 😁 Thanks for watching! We've been enjoying your videos!
@restoredmusclellc
Жыл бұрын
Thank you very much
@UglyTruckExperience
Жыл бұрын
Thanks for watching!
@Go69
Жыл бұрын
And... if you want to give the steering wheel effort a boost-meaning make it feel less easy to turn, or give it more "road feel" by slightly upping the effort required to turn the steering wheel-you can change the flow control valve out to a 2.5GPM, or even a 2.0GPM. They are widely available on the internet and will greatly increase the steering wheel turning resistance. When I swapped my 70 C10 over to LS I found the steering was SOOOOO easy.. Like you could parallel park using just a pinky finger.. Then I swapped out the flow control valve and got the wheel to a point where it felt much more comfortable. It then lost the cruise ship steering wheel feel, and got something closer to like what a performance car, or even the newer import cars, feel like. I LOVE making these modern updates to the older vehicles. And.. if you really want to upgrade the steering, you can use a mid 80's truck power steering box that has fewer turns lock to lock! You can get 3 turns, or less, lock to lock, which is also a great upgrade to the steering. Fewer turns, and more resistance, make for a "tight" steering feeling going down the road. LOVE these old trucks. Great job on the video! You got a like from me!
@UglyTruckExperience
Жыл бұрын
Great info! We have the close ratio gearbox on our 70 C10, and the LS pump made a huge difference in how it drives. But now you're making me want to play around with the control valve and see what happens. Thanks so much for liking the video! We appreciate you watching!
@cjjohnson1821
Жыл бұрын
Great video. That pre-bent return hose is $34.00 now lol
@UglyTruckExperience
Жыл бұрын
Thanks! We appreciate you watching!
@lparsons6977
Жыл бұрын
Thanks
@UglyTruckExperience
Жыл бұрын
Thanks for watching!
@soldozer
Жыл бұрын
I like how you show real world fixes with detailed video and parts info. Unlike Simple C10 channel is just making videos to promote the Amazon affiliate links. Its very spammy.
@UglyTruckExperience
Жыл бұрын
Thanks Mr Yuk! I can't knock someone for trying to make a living, but it can be super annoying. We try to keep everything simple and budget friendly. 👍 Thanks for tuning in! --Emily and Jerry
@FUCKEDUPFAB
Жыл бұрын
I belive you can take the old fitting out of the 350 ps pump and put it in the newer ones to use the flair fitting without an adapter if you have a old ps pump
@UglyTruckExperience
Жыл бұрын
That is correct. Most of the time when I get these the pump is already gone though. I also like to just use the fitting for in the future if somebody is changing the pump there is less chance for a problem. Thanks for watching.. We appreciate it.
@716_sam1
10 ай бұрын
I wish I found this video before I spent $190 on getting a line made. Still turned out great but your way would have probably saved me money on the hose and gas money 😅
@UglyTruckExperience
10 ай бұрын
Extra gas money is always a plus! Thanks for tuning in!
@Fentertainment
2 жыл бұрын
Question: I have a 97 Vortec 350 in a 85 c10. I have a 6.0 for the 85 but the PS pump has a separate reservoir. Would the PS pump that is on the vortec motor now fit the LS?
@UglyTruckExperience
2 жыл бұрын
That's a great question.. I'm just taking a educated guess but I would not be surprised if it does work. I have never tried so could not say for sure. If you give it a shot and it does, please let us know. Good Luck.
@GMGUY1000
8 ай бұрын
Doing an 86 4x4 from 6.2 diesel to 02 5.3 Ls holly/edelbrock.. vic jr msd 4016.engine plate and 700r4-208.
@UglyTruckExperience
8 ай бұрын
That sounds like a great project GMGUY. Keep us posted on your progress. The fuel system is really interesting to me.. Thanks for watching. Jerry
@salvatoregiovanni8967
2 ай бұрын
What else would I need to do on my 77 C10 that has a manual, non power steering box? Besides the obvious pump and line modifications that you mention?
@UglyTruckExperience
2 ай бұрын
Hey Salvatore. Sorry to just now respond. If you have a manual steering box. You will have to install a power steering box and just run a pressure and return line to it. You may have to adjust the tie rods afterward to make the steering wheel straight, but that is it. Thanks. Jerry
@brianhaw9398
2 жыл бұрын
Someone told me ls power steering is much higher pressure than older Chevy's. Do you know if this is true?
@UglyTruckExperience
2 жыл бұрын
Yes, and it works much better!
@aguitarhero007
Жыл бұрын
I bought that high pressure for my 86 camaro. The fitting that goes into the steering box fits properly except when it bottoms out the hose is still free. Is there a fix for that? It will rotate freely and lift up and down. In the video it said it works with 67-87, are there exceptions to that?
@UglyTruckExperience
Жыл бұрын
That 86 Camaro original hose should fit directly into the LS power steering pump without any kind of adapter. As long as the bends in the hose reach the pump ok. If it is an O-ring fitting I am not sure why it would move around in the pump after being tightened. Look that fitting over good and make sure it is the correct thread. Let us know what it turns out to be. Thanks Jerry
@tylerchristofferson1746
Жыл бұрын
Hey boss, doing a 79 c10, lq4 swap. I have that hydro boost line on the side of my pump. do i just leave that line disconnected if not where shall i connect it to?
@UglyTruckExperience
Жыл бұрын
That line just gets capped off at the pump. Make sure you use the lower return fitting also. Cap off the higher return. Thanks
@mrmidnight32
2 ай бұрын
Does anyone know the part number for that CPP fitting? I’d like to do this but go to a 16AN fitting instead of the factory crimped hoses. I just need the fitting size and type that goes into the pump so I can match that to an AN fitting
@UglyTruckExperience
2 ай бұрын
The part number is 605SOL. Here's a link to them on Summit, it has all the info you're looking for. We appreciate you tuning in! www.summitracing.com/parts/clp-605sol
@nelsconey
Жыл бұрын
what do you do about the O2 sensors for an LS swap on the new exhaust system?
@UglyTruckExperience
Жыл бұрын
Thanks for watching! We weld in new O2 sensor bungs in the new pipe in about the same position that the original front O2 sensors were in. We eliminate the rear O2 sensors and have them deleted from the PCM when it's programmed. Check out this video for more info! kzitem.info/news/bejne/tYVtp6uHe19jjWk
@shawnkennedy8425
5 ай бұрын
I have a new pump on a 383 for my 85 square body 4x4 the pump is a flare style I believe and my lines are o ring style. Do they make an adapter for that? I bought the one you mentioned thinking it would work and it does not
@UglyTruckExperience
5 ай бұрын
Hey Shawn. If you still have the pump that you removed, you could take the fitting from the original pump and install it into your new pump. The adapter that I was referring to went from flare to o-ring. You might have to get a hose from a earlier year with the flare if not. The earlier hoses were flare and somewhere in the early 80"s they went to the o-ring. I screwed up in that video and gave the impression that they were all flare up until 87. Not sure why your pump would be the older flare though being an 85. Jerry
@isaac-io1dm
2 жыл бұрын
I’m doing a 5.3 swap on a 1990 Chevy truck is there a big difference between the one your doing and the 1990
@UglyTruckExperience
2 жыл бұрын
I believe the fitting at the pump on your 1990 is a o ring fitting so you may be able to use its original power steering hose. I have never swapped a obs so I could be wrong. Let us know how it goes. Thanks
@thetotlpkg
Жыл бұрын
I took my c10 pressure line and put it on the Ls pump. It fits without the adapter. Will it leak or fail with out the adapter?
@UglyTruckExperience
Жыл бұрын
If it seemed to fit ok you may have a pump that the pressure fitting may have been changed. Otherwise, time always tells. Let us know what happens. Thanks
@ghogman
2 ай бұрын
Question, what do I do with the vaccum boost fitting I'm not going to use? Just plug it off? If so how?
@UglyTruckExperience
2 ай бұрын
Hey Gary. There is a plug that is made specifically for plugging the vacuum port on those manifolds. They are used on the trucks with hydroboost. Here is a link for an aluminum one. The OEM are plastic. www.google.com/shopping/product/11535207499144862754?q=ls+vacuum+plug&sca_esv=0a002056b542477b&sxsrf=ADLYWIJttlR8oSBD2CGQtuApGQxG8B1_dA:1715799635621&ictx=111&biw=1231&bih=575&dpr=1.3&prds=eto:2326625722502819540_0,pid:9682403238389560163&sa=X&ved=0ahUKEwjY-Jztq5CGAxUw4MkDHR6yBHgQ8gII-wkoAA
@jamrmask
2 жыл бұрын
For the holders you made for the wiring at the front of the oil pan, where did you get the plastic clamp?
@UglyTruckExperience
2 жыл бұрын
They're on the original wiring harness, but you can buy them brand new in any size. They're pretty handy. Thanks for watching!
@jamrmask
2 жыл бұрын
Was able to find them on Amazon. HE90 Wire Harness Routing Clip Assortment.
@chetterchez
7 ай бұрын
Having issues with my power steering on my swap. Steering wheel jerks around and steers by itself after hooking up the LS power steering pump to my 1983 C10 steering gear box. Do I need a pressure reduction kit installed so it doesn’t do that??
@UglyTruckExperience
7 ай бұрын
That is what I would start with. Sounds like your gearbox is not liking the higher pressure. Jerry
@chetterchez
7 ай бұрын
@@UglyTruckExperience Thanks. I ordered a Borgeson 899001. I will play with the adjustment and see if that fixes it.
@danjim7056
5 ай бұрын
So, some of these have a solenoid thing and plug coming off the pump that changes pressure wirh vehicle speed or something like that. Can I just take that shit off? I was confused when my line goes in from the front under the pump.
@UglyTruckExperience
5 ай бұрын
Hey Dan. Yes, you can just leave that off. My 74 has the same thing on it and I did not connect it when I used a different harness. It was only around for a couple years. I think they figured out that it didn't do anything worth while. Jerry
@danjim7056
5 ай бұрын
@@UglyTruckExperience thanks for the duper quick reply!!! Your videos have helped me greatly.
@JesusArzate-nv9io
Жыл бұрын
Have you guys done one with a hydro booster?
@UglyTruckExperience
Жыл бұрын
Hello Jesus, No we have not added a hydro boost to a swap yet. Have always wanted to though. Thanks for watching. Jerry and Emily
@Mel-Family
5 ай бұрын
Stupid question. I did my lines the same way you did, so I know they're right. When I first started my engine I forgot to put power steering fluid in (it was empty). It didn't make a single sound. It didn't run but maybe 10min without fluid. I have since filled it and worked my steering from lock to lock several dozen times with the engine off and with it running. I have zero power steering. It's full and doesn't make a peep. Is it a bad pump? I guess Ive never had a pump go bad on an LS with my other vehicles.
@UglyTruckExperience
5 ай бұрын
No such thing as a stupid question here! Your pressure valve may be stuck. It's on the back of the pump where the pressure line screws in. You can try turning the wheel back and forth with the engine off to free it up. If you can do it with the front wheels off the ground it's a little easier. Those pumps are really tough. You could run it without fluid for a long time before it would burn up. Let us know how it goes! Thanks for watching! --Jerry and Emily
@Mel-Family
5 ай бұрын
@@UglyTruckExperience I did that already.... I'll try again tomorrow but more vigorously lol
@Mel-Family
5 ай бұрын
Well that didn't work.... I tried with it off and went back and forth for nearly 10 min with it in the air as aggressive as I could and tried the same thing with it running. It still doesn't work.
@dannyshotrods3445
2 жыл бұрын
I have a question for you guys. What's the cheapest way that I can control a 4l80 in my 92 Sonoma with a small block. Can I do it with the pcm and harness from the doner truck , or do I have to drop like 1200 bucks on an aftermarket tcm?
@dannyshotrods3445
2 жыл бұрын
@@UglyTruckExperience Thank you.
@UglyTruckExperience
2 жыл бұрын
I should have read your comment more closely. If your running just the computerized transmission it would probably be easiest to use the aftermarket controller. Probably not the cheapest though. If you were using a stock controller I would think that the ecm would just need to know rpm and the speedometer signal. That would be a question for a person that does the programming. Shift points would probably need to be programmed for whatever your running it behind. Thanks
@scottwithoutadoubt1405
2 жыл бұрын
I’d recommend the stand alone controller, the stock computer uses inputs from the engine that one may not be able to map out of, and unless you can provide an alternative input it will mess with your transmission shift program. Unless you have a really good person to reprogram.
@terryeaster2508
Жыл бұрын
What’s the part numbers on the o ring to flare adapter
@UglyTruckExperience
Жыл бұрын
It's a CPP 605SOL. The part numbers for the hoses are in the description if you need those as well. Thanks for watching!
@PennyPinchGarage
Жыл бұрын
This should work on a 67-72 truck too right?
@UglyTruckExperience
Жыл бұрын
Yes it will! Thanks for watching!
@Slim.t07
Жыл бұрын
What’s the part number on the O-ring fitting from Summit?
@UglyTruckExperience
Жыл бұрын
It's a CPP 605SOL. Thanks for watching!
@yamahondazuki95
Жыл бұрын
Would this be the same for a 6.0 also?
@UglyTruckExperience
Жыл бұрын
Yes it is! Thanks for watching!
@Mrisra69
5 ай бұрын
On the pump Which one is pressure ?
@UglyTruckExperience
5 ай бұрын
The threaded fitting on the back bottom of the pump is the pressure line. If your donor had hydroboost, it will have 2 return lines that just have a flared steel line for a hose clamp. You'll want to cap the return on the side of the reservoir and use the other for your return, if you don't plan to use hydroboost on your swap. Hope this help! Thanks Israel! --Emily and Jerry
@NDB390
Жыл бұрын
Are your crimp fittings just pex fitting crimps used on house plumbing ?
@UglyTruckExperience
Жыл бұрын
Yes, the 3/8 fuel line uses the 1/2 inch pex crimp clams. I also have an assortment of other sizes that I order on line. Thanks
@NDB390
Жыл бұрын
@@UglyTruckExperience Awesome. I already have the crimper and fittings from my house remodel. Great Idea! Love your channel! So much useful knowledge.
@UglyTruckExperience
Жыл бұрын
Thanks, We appreciate you watching.
@jbsgarage8260
Жыл бұрын
Do you happen to have the part number for the metal hose on the return side?
@UglyTruckExperience
Жыл бұрын
What year is your truck?
@jbsgarage8260
Жыл бұрын
@@UglyTruckExperience 85 c10
@diesellife7450
Жыл бұрын
Love the video content, just noticed you guys are in strafford, I'm in Fairgrove an doing a 2008 4.8 swap on 79 c10 an could use some help on wiring up the terminator x max, an some other things. Do u have a contact number?
Пікірлер: 109