Great video Keith, thanks for sharing this valuable information. I have alot better understanding of the Data information. Take care, Ed.
@TotalSeal
Жыл бұрын
Thanks!
@rickseeman5679
Жыл бұрын
Thanks Keith. I let the battery go dead and it went back to default parameters and I forgot how to put it back. Thanks
@TotalSeal
Жыл бұрын
That’s why me made this video!
@MrDanielSoliz
2 жыл бұрын
Great info, thank you.
@TotalSeal
2 жыл бұрын
We hope it helps!
@fopahsedrick1707
10 ай бұрын
Can this tool work on bigger cylinder liners, like 260 mm and above?
@TotalSeal
10 ай бұрын
Yes, absolutely
@golfer0422
5 ай бұрын
When performing the scratch test for calibration, how far off should the reading be? I am using the standard 116 calibration block and want to know how close it should be reading to the 116.14. Thank you!
@BlackMercury3030
5 ай бұрын
If you're using the Mitutoyo reference specimen it came with it should be very close (115/117 range). Like the video showed you may need to do the update (red button) of the calibration a few times but it should end up close to your expected value.
@golfer0422
5 ай бұрын
Yes, im using the one that it came with. @@BlackMercury3030
@golfer0422
5 ай бұрын
If my reader is not reading the 116, but say 114 and I want to tell my machine that it IS 116 since that is what is should be reading...is there a way to change the reading in the machine and then run the test again where it would ideally THEN read it as 116? I hope that makes sense. TIA
@jameshemmings1542
3 ай бұрын
is there a way to adjust the orientation of the stylus? the one I'm using looks like its slightly off the the side when looking at the detector from the front.
@TotalSeal
3 ай бұрын
Not that we are aware of
@straightupbmw
Жыл бұрын
Hi, where can I obtain the adapter to use in my cylinder bores 82-90 mm bore diamater
@TotalSeal
Жыл бұрын
Not sure about a small bore adapter. Typically, the drive unit is located outside the small bore cylinders and the stylus reaches into the bore.
@andyoohhh2061
10 ай бұрын
How do you change the units from micro meters to micro inch?
@TotalSeal
10 ай бұрын
It is in the settings menu
@andyoohhh2061
10 ай бұрын
@@TotalSeal if I go to "Switch units", it gives me one option of units which is "mm". Any idea why it only shows one unit?
@saahilsamant9601
Жыл бұрын
I am using this profilometer to measure surface deviations on a piston. While taking identical measurements without moving the environment or changing any settings, I am observing a gradual drift along the X-axis when I superimpose the graphs on top of each other. What could be the reason?
@TotalSeal
Жыл бұрын
Contact Digital Metrology for help with a question like that.
@chandasab9048
7 ай бұрын
Sir I need starting setting of sj 210 machine
@JBlinky67
Жыл бұрын
Any idea how to reset it to factory specs?
@TotalSeal
Жыл бұрын
There is a factory reset option in the system settings menu.
@gogoltuhin
4 ай бұрын
How to convert Lambda c from in to m
@alexhise968
2 жыл бұрын
Boy oh boy have I had a hard time finding a machine shop that first off even has a profilometer of this level. Second work with me or my engine cause its a Toyota 4cyl. Third have a honing station and stones able to achieve the correct results. I called 62shops
@TotalSeal
2 жыл бұрын
That says something right there! You might want to contact Rottler to see if they can tell you who has one of their honing machines near you.
@alexhise968
2 жыл бұрын
I tried that a while back but both they and I were a bit to busy to get that figured out. I finally found a fairly new shop in Watertown SD. Also tell Lake to look for a KZitem link I emailed him a on October 10th.
@josephwhiting605
3 ай бұрын
My stylus is scratching my calibration reference and giving me a reading .45uin
@nightmissioncustoms
2 жыл бұрын
PLEASE clarify and elaborate on the stylus selection (5um vs 2um) and corresponding Lambda "C" values in the profilometer setup. They DO NOT produce the same values on the same surface. Also, please indicate how your bore finish recommendations are specified accordingly. The bore surface numbers are essentially meaningless without the proper equipment setup and measurement parameters clearly defined. Thanks!
@TotalSeal
2 жыл бұрын
The SJ-210 comes standard with a 5um stylus, and we set them up with a Lambda C (cut off length) of .1 That’s our recommended set up, and the published surface finish recommendations are based on those set up parameters. Rpk 10-15 micro inches Rk 35-40 micro inches Rvk 50-60 micro inches
Пікірлер: 31