Thank you very much for this tutorial ! I was able to save my D4WS ! My welds weren't visually damaged like yours, so I didn't really believe it, but it worked ! The solders are complicated because of the residual resin which interferes with the heating of the original solder and the addition of tin. To close I filled with a two-component resin for electrical junction boxes. Then I placed a large metal washer and metal tape.
@rikuhellevaara4369
8 күн бұрын
Thanks for sharing this. I had error code CPM-1001 Combustion fan. Signal too high" on my 2010 Volvo V50 which has CAN-controlled Eber D5WS. I also had bad soldering on my PCB but it didn't fix the problem and replaced the old fan. My problem got fixed when I detached the PCB from case and isolated the PCB with some electrical tape and not attaching the PCB screws. Then the grounding comes only via wire. Hope this info helps someone else.
@gigibalcon
7 ай бұрын
Multu pentru video, am reusit sa resuscitez si eu unu cu problema asemanatoare! ✌️🤟
@vreaucs
3 ай бұрын
si eu mai multe. eu am frezat si am relipit toate contactele✌✌✌✌ ideea mi a dat o un tehnician de la eberspächer
@matzyboy92iphone70
Жыл бұрын
Thank you i will test this on my burner cant buy new ecu
@jelleelberse3201
11 ай бұрын
If you want to drill a hole without a center because it's dangerous. First dril a hole In a bit of wood with the centers en then glue or clamb that hole on your work and make a stop on the holesaw
@Osoppi
10 ай бұрын
Yeah with the center bit you can drill through the circuit very easily. Your method works too but the safest option is to use drill press and the holesaw without a center bit.
@smcsumo
2 жыл бұрын
Very good tutorial👌
@Steve.191
2 жыл бұрын
Thanks 👍
@havenissen8185
6 ай бұрын
Hello, do you know anything about error 71 and 17? I can see that it is related to the temperature sensor, i tried measuring the resistance on the sensor and that reads okay. I tried shorting the wires to the sensor like the manual says to do, but that didnt change anything either. I originaly had the error 31 and used you video to fix it, but now i get the error 71 and 17. I read in the manual that to test the controller for the heater i would need the diagnostic tool you use in this video but i dont have access to one. I hope you have an idea for a solution.
@Sorin-cu3ub
10 ай бұрын
Salut, vad ca esti din cluj, am exact aceeasi problema la un d5ws, ba merge ba nu merge, eroare 31. Crezi ca m-ai putea ajuta cu o manevra de genu asta ? daca il aduc demontat bineinteles.
@ioogy1
Жыл бұрын
Buna ziua, pe un Viano 2009 alerta din logurile masinii este: “component a6m1(combustion air blower) does not function properly “. Credeti ca as mai putea cerifica ceva inainte de a aplica procedura descrisa din video? Multumesc anticipat pentru eventualele raspunsuri si efortul descrierii problemei.
@DIYHelper
Жыл бұрын
Dacă ați încercat ventilatorul și este ok, cam asta rămâne
@kiparosu
Жыл бұрын
Buna ziua! Am o unitate Eberspacher Hidronic D5WS. Ma puteti ajuta cu service ul? Nu porneste decat ventilatia in masina si pompa electrica de circulare apa. Unitatea nu arde motorina.
@DIYHelper
Жыл бұрын
Bună, din ce zona a tarii sunteți?
@romanspychaa6843
9 ай бұрын
Witam mam d5ws i jest błąd zwarcie pompy wody do masy a wszystko jest ok
@farkasalex-hm7vm
Жыл бұрын
Salut,am un eberspacher d5wz de pe un sharan! As putea sa il pornesc fara masina? Adica fara calculatorul masinii? Ma poti ajuta cu o diagrama eventual? Vreau sa il montez pe un focus.... mulțumesc anticipat
@DIYHelper
Жыл бұрын
Destul de dificil, trebuie pompa de apa, controller etc. Am nevoie de codul de pe încălzitor cel 25xxxx sa vad care generație e de pe sharan
@farkasalex-hm7vm
Жыл бұрын
@@DIYHelper ok,am sa il caut! Pompa de apa o am,de combustibil o am! Daca as putea cu o comanda simpla printr-un releu sa o pornesc,ar fi bestial!😁 mulțumesc
@smcsumo
Жыл бұрын
What type of sealant do you recomand to seal the hole?
@DIYHelper
Жыл бұрын
Well it should be able to resist at least to 90 degrees
@albualexandru1253
Жыл бұрын
Bună ziua. Am o problemă cu aertronic S3 după oprire ventilatorul continuă să funcționeze la o turație mica . Spune ca trebuie montat un al doilea termostat . Am si diagnoza originală eberspächer. Cum ar trebui sa procedez. Clientul vine în 2 săptămâni este montat pe o caravana încă nu am avut acest tip de problema . Mulțumesc mult
@DIYHelper
Жыл бұрын
Dacă aveți Easystart Pro trebuie setat sa funcționeze după senzorul din elementul de comandă.
@albualexandru1253
Жыл бұрын
@@DIYHelperAm controlerul EasyStart Remote+
@DIYHelper
Жыл бұрын
Chair dacă aveți easyscan nu veți putea lega un senzor exterior. Trebuie modificat un parametru în configurația încălzitorului pentru a funcționa cu senzor exterior la care nu veți avea acces. Trebuie sa luați legătura cu reprezentanta
@albualexandru1253
Жыл бұрын
@@DIYHelper Multumesc mult de informații. Mult succes în continuare!
@AdrianCiubancan_
Жыл бұрын
De unde sunteti ,? ma puteti ajuta si pe mine cu diagnosticare montaj webasto ?
@roberttoca1895
Жыл бұрын
Salutare, am probleme cu un Eberspächer hydronic II D5Z-H de pe Toyota Auris 2008. Nu da nici un semn de viață. Va pot contacta la un nr de tel?
@DIYHelper
Жыл бұрын
Bună din păcate nu ma ocup de servisare, modelul dvs pornește când temperatura antigel ului este sub 5 grade dacă bine rețin și funcționează doar odată cu motorul. Dacă îmi spuneți localitatea eventual va pot recomanda un service în zona.
@roberttoca1895
Жыл бұрын
@@DIYHelper Sunt din Hunedoara. Masina o am de 3 ani si sirocoul nu a pornit indiferent de temperatura de afara. Am masurat tensiunile pe mufa si ar avea toate condițiile sa pornească. +12v permanent, +12v cand pornește motorul si +12v cand apăs butonul pwr heat. L-am desfăcut, e f curat, funingine aproape deloc pe evacuare. Ce ma sfătuiți sa fac? Stima
@marian7186
Жыл бұрын
Salutare ! Acel ventilator functioneaza la 12v sau la 8.4v cum scrie pe el ? Multumesc !
@DIYHelper
Жыл бұрын
Se poate încerca foarte scurt la 12V dar el funcționează la tensiunea scrisa.
Пікірлер: 34