Was going mad putting the cover back on and you adjusting the tension screw saved me. Thanks!
@marlonearlgordon6974
7 ай бұрын
Interesting information, watching from jamaica 🇯🇲🇯🇲🇯🇲,I have one of the Echo CS 310
@spideywhiplash
2 жыл бұрын
Thanks! Though, my OCD really wanted you to spray the inside cover clean with brakelene before putting it back on. Ahhhh, the joys of Brakelene. Makes my brain flutter with delight.😁
@lokaniukas
7 жыл бұрын
Clear and nice video. A small amount of grease on the clutch bearing can be also added while you're there.
@billgatewood5029
2 жыл бұрын
Thanks man. Very helpful! Keep it up.
@TheTinotinotino
8 жыл бұрын
Good job man !!! You Make it easy.
@CliffsHowTo
8 жыл бұрын
Thank you!
@viperstrike3827
2 жыл бұрын
Thank you for the video, I know how to do this I just watched for fun.
@marlongordon390
3 жыл бұрын
Very good introduction
@BAKERHUSKIE
4 жыл бұрын
Blowing all the debris would've been good before installing the sprocket. And some grease too.
@romel7144
Жыл бұрын
I have th3 same model and the I was cutting and it the chain stopped moving. Have any ideas?
@CliffsHowTo
Жыл бұрын
Hmmmm. Not sure. Sorry. I don’t have a lot of experience with chainsaws, honestly.
@viperstrike3827
2 жыл бұрын
I know this is an old video, but I hope you kept that bar as a beater for when you know you are going to get in dirt.
@stephanfiebich1561
2 жыл бұрын
On mine the studs pulled out of the plastic housing
@Americasoutdoorfamily1
4 жыл бұрын
Where did you get the kit from
@CliffsHowTo
4 жыл бұрын
I honestly do not remember.
@derekthomasgriffin
2 жыл бұрын
that metal round piece doesn’t work like that on mine. It doesn’t fall right in. There’s a metal round ring that is preventing my thing from dropping in like that. ??
@JamesBrown-ru9ri
Жыл бұрын
You got to pull brake handle back and it releases tension in metal round piece. I had same issue 🤣🤣while watching had to look at few other videos
@mustangracer1917
Жыл бұрын
what is your bar size ? 14 or 16 ?
@CliffsHowTo
Жыл бұрын
Not sure, I’d have to look. Same process regardless I’m sure though.
@a1930ford
3 жыл бұрын
C-clips have a really nasty habit of finding their way to the darkest depths of the corner of you workshop so that you spend the whole afternoon looking for them. Screwdrivers always love biting your fingertips when one of those C-clips decides to spin across the room, too. :-) Not sure why God chose to not give us humans a 3rd hand to hold the saw, hold the screwdriver and hold the camera all at one time. Question: Are you not supposed to tip the front of the bar upward when tightening down the locking screws on this chainsaw? Not sure if that is required on this saw, but I know it is on other brands. Just got one of these today and I am viewing all the videos i can to see what works and what doesn't on them.
@CliffsHowTo
3 жыл бұрын
I’m honestly not sure.
@robertfink4081
3 жыл бұрын
Definitely... I even have the bar up while tensioning the chain and then while tightening those lugs
@joesabal1212
2 жыл бұрын
Why didn’t u show the inside of the clutch bell. After all that is where the clutch makes contact with the clutch bell.
@CliffsHowTo
2 жыл бұрын
I didn’t think that was relevant? I don’t know… I just changed out the parts that I could see needed replacing.
@solohoh
4 жыл бұрын
Most kits come with a bearing, did you replace that?
@stugats77
4 жыл бұрын
can i put a longer bar n chain on my echo cs310??
@CliffsHowTo
4 жыл бұрын
Sure. Although I wouldn’t go too much larger, as the engine is sized properly to drive the bar/chain.
@danmyers4490
2 жыл бұрын
Only up to a 16”
@brandonsarazin3257
4 жыл бұрын
is so worn out because he must be using a chain with the wrong number of links.
@CliffsHowTo
4 жыл бұрын
That was the original equipment that came on the saw
@jerometremblay5258
3 жыл бұрын
Could you Tell me how to change à broken bar bolt
@cbnx82703
5 жыл бұрын
This is a how not to change your Bar & Chain video ....!!!
@CliffsHowTo
5 жыл бұрын
Really? What was done incorrectly?
@cbnx82703
5 жыл бұрын
Cliff's How To Channel , I am a Stihl Platinum Certified Technician with 38 years experience, where do you want me to start ? How about the most obvious two things , when you set chain tension the bar tip must be at it’s highest setting , meaning pull the bar tip up as you adjust the chain tension and when you tighten the bar nuts use a ratchet or the Scrench supplied with the new saw . Tighten the bar nuts more than finger tight holding a socket in your hands. And then rotate the chain on the bar to test proper tension because often times the chain on the clutch drum sprocket is not fully seated and will loosen after one rotation of the sprocket . Recheck after always ....
Пікірлер: 36