Great video, and thanks for explaining everything first and showing everything. Doing it at a good pace, not just saying, plug in here, then next step. You actually showed easy ways to do it. +10 for you good sir
@FalconsGarage
10 жыл бұрын
Might be a dumb question. But what's the point of the elbow on the waste gate? Why not keep the old one?
@thoroughbreddiesel
10 жыл бұрын
The boost elbow will keep you from having your wastegate open to early. For example, if your wastegate gets weak and begins to open at 25 psi, this will hold the wastegate closed and let the turbo boost to whatever level the engine is set up for.
@AR50sniper
7 жыл бұрын
Just curious, how does the unit read boost psi? I only see you changing out the waste gate elbow and installing the stock tube back on.
@MadisonColeman-o2r
8 ай бұрын
This video was super helpful, but how do you go about doing it with a BD stealth plate, can't find anything helpful anywhere on the topic.
@nwyoda8792
9 жыл бұрын
I have 99 2500 with the kit. factory tach comes on but 2seconds later when the edge screen comes on the factory tach dies. What could this be?
@Johnsonkelley007
10 жыл бұрын
start the motor an run it during the drilling procces. it will bolw and unwanted shaveings back out the hole.
@kfx400tt1
9 жыл бұрын
As far as I know the cts is touch screen unlike the cs not sure on other differences ???
@thoroughbreddiesel
9 жыл бұрын
No difference, just touch screen vs not.
@04282
9 жыл бұрын
my turbo has a hard line.. and can only get about 18 pounds of boost.. any suggestions???
@thoroughbreddiesel
9 жыл бұрын
paul dulac Your truck is the automatic? You can use a BD X hook, p/n BDD1045991 if your truck is the 01-02 Auto. This will allow you to build more boost without the wastegate creepin.
@pauldulac8506
9 жыл бұрын
Thoroughbred Diesel ok cool. Great video by the way! ! Do you have a link to a page i can purchase that part??
@pauldulac8506
9 жыл бұрын
Paul Dulac yes it is the 2001 auto
@thoroughbreddiesel
9 жыл бұрын
Paul Dulac We do! www.thoroughbreddiesel.com/bd-diesel/turbo-x-hook.htm
@sambo4054
6 жыл бұрын
I want this but for a 2002!!
@bradleyrussell8180
Жыл бұрын
When my pump gets here that I ordered from you guys, and it's installed, I want to order this upgrade. But, does it come with the EGT probe?
@thoroughbreddiesel
Жыл бұрын
Yes, the Juice with Attitude does.
@bernhard8540
3 жыл бұрын
To keep the shaving out of the engine I start the truck if possible and it will blow them out as you drill helps with keeping it clean :) I've seen some people use grease on the tap and drill bit as well but it's messy haha just gotta be careful bigger pieces don't go through the turbo haha ❤
@chrisk4177
3 жыл бұрын
What is the pump tap wire for
@angelrios2312
3 жыл бұрын
Does Part number vary for a 6speed Manual?
@zx3499
9 жыл бұрын
I like to use a vacuum to clean up shavings, and use a dropcloth (I.e t shirt) to catch small screws that I'm trying to assemble. Awesome video, thank you!
@Logdogsmith
10 жыл бұрын
Just drop that on the concrete! haha
@davidyoder1219
10 жыл бұрын
Is the comp box the same as the juice with attitude cts/cs just without gauges?
@thoroughbreddiesel
9 жыл бұрын
For the most part it is the same, without the gauges and the safety capabilities
@damnationdefied777
11 жыл бұрын
I appreciate what youre doing but i have to also sit back and look at the bigger picture. Having just bought a cummins, i think its crazy to have to go through a process like this just to watch the numbers and figures to make sure the truck is safely operating. These gauges should be a factory requirement on the dash.
@carsonh7988
2 жыл бұрын
Is this the same for a 2001 Dodge Ram juice with attitude? Even in 2022
@thoroughbreddiesel
2 жыл бұрын
Yes sir, only the shape of some of the sensors will differ, but their location will be the same.
@phagoy3006
2 күн бұрын
@@thoroughbreddiesel I am having same problem my map sensor connection is completely different I don’t know what to do do I have to plug map sensor and all That in?
@codymoore161
9 жыл бұрын
Anybody else catch that he was going the wrong way with the pump tap at first? Haha great video though.
@johnhalseyff
7 жыл бұрын
if we do not have any type of lift pump, where would the fuel pressure sensor go?
@thoroughbreddiesel
7 жыл бұрын
First and most important, if you only have a stock lift pump WE DO NOT RECOMMEND THAT YOU USE THE EDGE J/A!!!!!!!!!!!!! You would be MUCH better served to upgrade your lift pump first and then install the Edge. With that being said, if you have a stock line going into your VP, the Edge kit provides a banjo bolt for installation.
@johnhalseyff
7 жыл бұрын
Thanks for the reply. I don't plan on using any of the tunes that are 100 hp+ just yet for that reason. In due time I will get a lift pump when I can save up for oneI'm just getting a good deal edge J/A right now
@MrPablo8605
9 жыл бұрын
hello friend where I buy the harness dodge ram diesel engine 3949898
@mitmaks
12 жыл бұрын
What is there are some shavings that didn't get picked up by magnet, will it damage the turbo?
@Redneck350chevy
7 жыл бұрын
I have a 2006 2500 mega cab 5 9. Got a juice with Attitude 2 and it burned up my injectors and Transmissions run away they said the Chip And wiring was wrong what do you know of the juice with Attitude 2?
@thoroughbreddiesel
7 жыл бұрын
Those failures are unrelated to the Edge module. Please call to discuss further. 1 866 737-4966
@streetfamousgarage3435
4 жыл бұрын
I have this kit but have an issue, my map sensor is a round 3 prong plug and the edge has an oval 3 prong plug. Can I get a oval sensor and change the pigtail so then I can plug in the tuner? Any advice I’m open too, it’s for this truck idk if someone has tampered with it before
@joshuabreedenjr42
2 жыл бұрын
Did you ever figure this out?
@juliorobles6451
7 жыл бұрын
it a place in Austin texas where they can do all this?
@thoroughbreddiesel
7 жыл бұрын
I do not know off hand, I apologize. A search engine would help with that question.
@juliorobles6451
7 жыл бұрын
thank you for the time
@bluebird5100
5 жыл бұрын
I will be tapping pump with bd stealth cover. Will the pump tap wire plug from the edge plug directly into this?
@thoroughbreddiesel
5 жыл бұрын
Using a Stealth Cover, yes.
@markwood2389
5 жыл бұрын
I love my southbend clutch I got back in the summer from ya'll for my 2000 model 3500 Laramie..I've wanted a tuner for my truck for a while now..but I did all the must haves to my truck first..I trade on trucks for a hobby and I started trading on diesels about 4 or 5 yars ago..I got this one as well to resale..but I never enjoyed driving a truck more than the 2000 manual trans 24 valve diesel truck I have now..My truck is a 1 owner 158k truck..It had 146 when I got it last year..My question is is this tune the best for my truck..Im not trying to ever have a race truck out of the 2000 model 3500 2'WD that I have now..Its extreamly used for work..thats why I looked so long to find a 2'WD All Orginal truck..Not easy for a truck that's close to 19 years old..but anything is possible if you wait and look long enough.I just put 2 new batteries and all filters changed and al fresh fluids..I really want to try and get better fuel millage if possible..The only upgrades I have other than the new southbend clutch is banks cold air intake and 4 inch straight exhaust..I enjoy giving Ya'll my business cause you don't try and sale me something I don't need..Also I believe you all at Thoroughbred diesel care about me and all your customers like family..I'm really in no hurry I really don't need it..I really want to try and get a little more millage..I try to make ever dollar or gallon go as far as it can..Most of all I know I want to be the best stuart over what I've been blessed to have..Merry Christmas to you Wade & Family at Thoroughbread diesel and may God bless you all to have a happy new year., Edward Mark Wood.
@thoroughbreddiesel
5 жыл бұрын
I believe this is the best all-around setup for the VP Dodges for several reasons. 1. You get the ability to monitor several different parameters on the truck. 2. Tuning is a shift on the fly so that you can detune for different driving conditions. 3. Back down parameters help to keep the truck safe. 4. Functionality as a diagnostic tool is very helpful. This is a purchase that you will give you that much more enjoyment out of a truck that you already love. Merry Christmas to you and your family Mr. Wood, if there is anything we can do to be of assistance, please don’t hesitate to reach out to us.
@markwood2389
5 жыл бұрын
@@thoroughbreddiesel Thank You Wade for this information..Its on my wishlist..Santa's always been good to me so far..Looking forward to putting this on my truck!
@kycepayne9983
7 жыл бұрын
I have a gdp fuel boss mechanical lift pump how would i go about installing my fuel pressure gauge??
@thoroughbreddiesel
7 жыл бұрын
Depending on what size fuel line you run, we have cut and splice fuel pressure T’s that we offer. Here is one from Airdog: www.thoroughbreddiesel.com/airdog/fuel-pressure-tee.htm
@crf450ish
11 жыл бұрын
Put some wd-40 on that tap when your doin that
@thumper2692
4 жыл бұрын
I just ordered the edge juice, air dog raptor 150, and 4” exhaust from you guys, I was wondering if you know what gauge of wire you matched up to the fuel pressure sensor?
@thoroughbreddiesel
4 жыл бұрын
I believe 18 gauge.
@thumper2692
4 жыл бұрын
Thoroughbred Diesel thanks, I have installed everything including the juice with attitude, intake, exhaust, and lift pump, I’m a little concerned with my egts. Even on town tune I have seen spikes of 1400, when I get on it going up a hill, (obviously then it starts defueling) I did a lot of research and I thought with stock injectors I would be safe, I think if I got myself down 100 degrees I would be safe but I’m not sure what to do.
@swuay8718
3 жыл бұрын
Where’s the trans temp sensor located of a 5 speed manual transmission
@thoroughbreddiesel
3 жыл бұрын
We usually don’t install the trans temp on the manual trans, however if you would like to install it on the 5 speed the best place to put it is remove the pto cover and drill and tap it there.
@josefalero1087
5 жыл бұрын
Will work with a HO pump or this pumps have their own programming tunes?
@thoroughbreddiesel
5 жыл бұрын
Yes, this will work with the 6 speed or the 5 speed and Automatics. This video is for an old module that is no longer available.
@anthonyar4
5 жыл бұрын
P0193 after instal
@jon3124
10 жыл бұрын
is this install going to be the same for an 01? the 31001 kit?
@thoroughbreddiesel
10 жыл бұрын
Yes its the same process.
@ChrisWreckingTinkler
9 жыл бұрын
When I install my cs should I go straight pipe or can it wait ?
@thoroughbreddiesel
9 жыл бұрын
Chris T We always suggest doing an exhaust upgrade any time you do a performance adder like chips, module, injectors, etc.
@ChrisWreckingTinkler
9 жыл бұрын
Thoroughbred Diesel thanks for the fast reply , would you recommend a 4" or 5" exhaust
@dogy239
8 жыл бұрын
+Chris T 4''
@nwyoda8792
9 жыл бұрын
Its a 5spd If that makes any difference.
@thoroughbreddiesel
9 жыл бұрын
nwyoda87 Sounds coincidental. Your tach receives its signal from the crank position sensor. I would be willing to bet that you have a bad crank position sensor.
@nwyoda8792
9 жыл бұрын
I replaced cps two weeks ago. its only when the edge comes on that tach dies.
Пікірлер: 66