I really love your videos. The explanation is very clear and straight forward. Thank you!!
@sarahlabidi6558
10 ай бұрын
Positive EDGE, Negative EDGE to count only one time, move 0 to the three blocks to reset, thank you very mcuh😍😍😍😍
@andriibudaiev
10 ай бұрын
Great explanation. Your Siemens guides are very good!
@simonmax3901
4 жыл бұрын
U always give excellent tutorials.... keep up for good work
@anathiponi2003
4 жыл бұрын
Your tutorials are good and helping me man plz keep up the good work..
@hegamurl7434
4 жыл бұрын
Will do, thanks!
@JinsonKurianVJames
4 жыл бұрын
Nice. P_trig is extensively used in Simatic manager to set bit for an alarm and reset it even though alarm exists. But I got a new function in Tia portal as R_trig with static address is very compatible in functional blocks. Could you please distinguish P_trig and R_trig. Why did siemens introduced R_ trig? What is its advantage over P_trig?
@kaiqueTIAPORTAL
2 жыл бұрын
Man, you are a fucking education genius. Congrats for your lessons. Watching from Brazil
@zhengkunyan8001
4 жыл бұрын
good!!!!!!!!!very impressive,adding at each clock cycle which is created by sensor signal, and have reset to set all to zero
@chidoziriiroh9329
Жыл бұрын
Lovely and revealing
@khaledabdullah7802
Жыл бұрын
Thank you very for your great videos it really helped me alot in my projects 👍
@Olavotemrazaodenovo
4 жыл бұрын
Excellent
@paulchen1038
Жыл бұрын
Sehr hilfreich, vielen Dank!😊
@ayoubalaoui7905
4 жыл бұрын
Man, you are goddamn helpful.
@sarahlabidi6558
11 ай бұрын
really love your videos. Thank you!
@SDV610
3 ай бұрын
thanks very helpful
@_Iokanaan_Marusidze_
Жыл бұрын
Thanks 👍
@rolandomartinez458
3 жыл бұрын
Good work friend, it was great. Sometimes we have been working with P_TRIG in several parts of a program and the memory zone we selected for it stayed in true while the RLO was just down and we never knew why. Are there rules to use the P_TRIG I mean inside FBs, FCs and in the memory we select for it like Mx.x or Temp from instance DBs of FBs . Can you light to me. Thanks
@mbmsnabil4818
4 жыл бұрын
Hello, i did not understand "Data".Status Triggerd" how it is changing ? you have pressed the button just one time in my knowledge we should add one each push not more. thanks your are doing a great job.
@omarvalencia8863
4 жыл бұрын
PLC works like any other computre with a clock,, what the program gets is a High signal but read it has fast the computer (frame refresh) and PLC can work like 1ms,.iI you press 1 time but your finger stay there 15ms it works15 times . Hope this help you
@bensalemyoussef945
3 жыл бұрын
your tutorial is sehr good and helping. I have a question : how can I P-Trig or N-Trig in SCL writing? Thank you and keep going
@zainmalik7008
3 жыл бұрын
Sir your vedio is very helpful to me in programing kindly upload ur vedio about FXY& LDLAG funtional block working
@zhengkunyan8001
4 жыл бұрын
😄😄thanks💖
@gajendram6462
2 жыл бұрын
Super sir
@derina.maleek9408
4 жыл бұрын
Awesome thank you
@ahmedeissa2464
Жыл бұрын
Thank you for your videos, I have a questions how can I use P_trig while programming with SFC. Because I can't see any Bit Logic functions.
@peterhans8788
4 жыл бұрын
Hi @hegamurl How did you configure the variables? Once you defined as „Data“.“Pushbutton...“ and the Add function is connected to „Data“.“Edge Triggered...“ So different names? Why did. you not take the Same Variable? Same in the P-Trig and Same in Add function? Thanks for helping!
@yangajako9070
2 жыл бұрын
How did you link the “Status Triggered” value with the program (“ADD” block)?
@buntofori2768
3 жыл бұрын
Thank u
@rolandomartinez458
3 жыл бұрын
Dear Hegamurl. I have a problem with the triggers. The first time it goes up it stay activated. I would like to send to you a picture of the problem? Can I? How?
Пікірлер: 32