Very useful information. I used this method to remove the panel, probably saved me a couple of hours and a ton of pain from removing the bumper cover. One thing though -- the driver side screw is in a VERY tight place. If you have large hands/thick arms, it can be tricky.
@InsideBigJaysGarage
3 ай бұрын
A good callout.
@JacobBradford-h6u
3 ай бұрын
Great video. Thorough instructions, thanks.
@InsideBigJaysGarage
3 ай бұрын
Glad it was helpful! You are very welcome.
@chadnewsome8525
15 күн бұрын
Question: after installing the hitch/new panel, am I correct in assuming that the removal wiring plate/cover does not get re-installed? I was thinking it would but I don’t see how it can fit once the wiring outlet/harness is installed. Just wanted to confirm and thanks again for a super video!
@InsideBigJaysGarage
15 күн бұрын
Correct. If you have the wiring harness that silver cover has to come off.
@kevinc.oldham9159
3 ай бұрын
Thank, any special tools to remove those plastic clips ? I appreciate the effort you put in to help the rest of us.
@InsideBigJaysGarage
3 ай бұрын
You’re welcome! You can use a flat head screwdriver to pull the center pin out and release it. Or, if you want you can buy a kit like this in the link. They work well, too. a.co/d/099ZTdkM
@1hjehje
3 ай бұрын
An excellent video. Thank You!
@InsideBigJaysGarage
3 ай бұрын
You are welcome!
@levthelion
26 күн бұрын
You mentioned towing a trailer. What would be the next step to be able to use the trailer brakes? Would you need to install a trailer brake?
@InsideBigJaysGarage
16 күн бұрын
I don't have trailer brakes, so I don't have any input for you.
@fengjingliang6467
2 ай бұрын
Thanks for sharing! Very useful! I wonder do I need to replace the hands free adapter with the new 08L91-T90-100A Adapter, hands free assist (HFA with trailer hitch)? Thanks!
@InsideBigJaysGarage
2 ай бұрын
I did have to replace my sensor. I believe that is the part number. “T90” is for the 2023+ Pilot.
@rfedeleon
2 ай бұрын
Thanks for this helpful video. Do you to remove the rear tail lights in order to remove the panels in the trunk?
@InsideBigJaysGarage
2 ай бұрын
No you do not. The harness will have instructions on which panels inside to pull off.
@Lancel16
6 күн бұрын
Hey were are you located are you in Canada?
@InsideBigJaysGarage
5 күн бұрын
I am not in Canada. I am in upstate NY.
@VincenzoDom
25 күн бұрын
so once you remove the clips on the bottom of the silver part and the two 10mm bolts, it just pulls off? Or you have to work the tabs on the top of the piece?
@InsideBigJaysGarage
24 күн бұрын
IIRC once all the fasteners are off it comes right off.
@chadnewsome8525
16 күн бұрын
you have to release the 4 tabs from the top of the silver part/original cover. I used a trim tool to gently release each one while also gently pulling the cover and it came off fairly easily.
@VincenzoDom
10 күн бұрын
@@chadnewsome8525 thanks for the insight. Assuming using the trim tool from the finish side of the cover? Or from under the car? Pressing down?
@chadnewsome8525
10 күн бұрын
@@VincenzoDom from the finish/outward facing side of cover and I think it’s pressing down but as you start from one side you should be able to confirm as you pull out an little bit.
@VincenzoDom
10 күн бұрын
@@chadnewsome8525 appreciated!
@kevinc.oldham9159
3 ай бұрын
Can the new hands free lift adapter be installed as well without bumper removal?
@InsideBigJaysGarage
3 ай бұрын
Yes it can! Mount it before or after you install the new insert.
@jp-uo7bz
2 ай бұрын
Does your golden retriever slide around in the back while you drive?
@InsideBigJaysGarage
2 ай бұрын
No. Short trips to the park or vet she just lays down. Longer trips we have a large crate that she travels in.
@kennyluke2
3 ай бұрын
Does it interfere with the backing sensors?
@InsideBigJaysGarage
3 ай бұрын
No issues to report.
@jp-uo7bz
Ай бұрын
Is this all doable without lifting the car up and without a flat roller/creeper when working underneath?
@InsideBigJaysGarage
Ай бұрын
I did it with the car on the ground with no ramps or jacks. I used my creeper, because I have one. But, I don’t see why it could not be done without one.
@MrFlawless241
4 ай бұрын
So the stock bottom panel needs to be replaced with one that has the cut out for the hitch?
@InsideBigJaysGarage
4 ай бұрын
Yes, if you want to use the Honda Hitch that tucks into the bumper. The new panel will have a cut out and it’s more squared off so the hitch can fit behind it. If you look at a 2023+ Pilot TrailSport that is the panel you install. You can also purchase a panel in black if you want that part of the bumper to be black instead of silver.
@MrFlawless241
4 ай бұрын
@@InsideBigJaysGarage Thanks man
@InsideBigJaysGarage
4 ай бұрын
You are very welcome! Good luck.
@walterdannhardt7486
3 ай бұрын
Excellent write up, thank you very much. The hard part was reaching the 2 screws on top - much easier with the spare tire removed. I installed the new panel prior to installing the hitch. Also, the computer gave me all kinds of error messages when I started the car (collision avoidance, lane departure & etc). Fortunately the error messages went away after 1 drive cycle.
Пікірлер: 42