This is the design i was looking for on my go cart rebuild. i like the relocation of the key start & especially the TC design, Thanks!
@morepower3242
6 ай бұрын
That’s the cleanest swap I’ve seen looks professional
@sharptoothtrex4486
Жыл бұрын
That is a great one, lad. This also makes a great learner's permit starter car.
@BigBlok502
3 жыл бұрын
Very similar to my setup I did a couple years ago. Thanks for sharing.
@BubbaB43
2 жыл бұрын
I'm out in my 40 series torque converter straight to the reverse gearbox without using a bushing I just ordered a 5/8 bore driven clutch and then drilled and tapped the shaft to hold it in place. They also have the new 40/780 series torque converter reverse gearboxes, I own both and this new one is awesome!
@coltonlogan8492
2 жыл бұрын
Can I get a link for the gearbox? Having a terrible time finding one
@heading7593
Жыл бұрын
Im doing almost the exact setup but with a yamaha g1 trans axle this helped a bunch so thank you
@candycoatedrazrbladz
Жыл бұрын
Very nicely built.
@GDTractor
2 жыл бұрын
Excellent video! Well done and easy to follow! Thanks much!! GD Tractor !!
@ThomasBeasley-vu4ij
Жыл бұрын
thank you for sharing real nice build on your cart. I looking to add reverse transfer to my par car was electric now gas 18 hr need to find right transfer unit for 1 inch shaft motor
@REVNUMANEWBERN
6 ай бұрын
LIKE that extra pillow block support
@thomaspryor8202
3 жыл бұрын
Great build1
@coburnlowman
3 жыл бұрын
👍👍👍👍👍 Man you did a great job on this one!!! It's a clean looking one. To another commitmentor I told I have two carts that needs converting. So I'm glad to have found your video to get a good layout to do mine. Be so kind to tell me , how has the transmission held up so far? Do you pull anything with your cart ? Also do the belts last long on the torque converter? I thank you again for the video.
@tarzanmukai808
3 жыл бұрын
I loved the video, i do have a question on how did you make the gas pedal work to pull on the throttle arm.. I been lost on that connection part, any parts i need to buy or fabricate to make it work? thanks for the video
@clayhunna7357
2 жыл бұрын
you done agreat job! im thinking of doing my 40 series cvt direct to reverse gearbox too like yours. my question is how well has the gearbox stood up to to bigger load from the 40 series driven pully and big block??
@prebaned
7 ай бұрын
Same gear box on my Manco cart. Filled it to about 3/4 Inch from fill cap. I don't see how it can blow a seal out since the box is vented.
@jesse1136
2 жыл бұрын
Nice looking build, I've got an almost identical setup on a sxs atv. You said that you put a bushing on the driven pulley to bring it out farther, could you explain what you meant or what kind of bushing? I'm having trouble building a decent mount for mine that covers pretty much everything you said: minimal chains to maintain/adjust, adjustable engine mount plate for belt tension, etc. I hadn't even considered extending the input shaft on the gearbox, and my driven is installed the same as yours. Jackshaft really seemed unnecessary and I'm glad to see yours is successful.
@floridasfinestcustoms
Жыл бұрын
thanks for the belt info
@crucialboy18
3 жыл бұрын
Great job. What was the top speed on this build?
@davjaramillo
3 жыл бұрын
Thanks for the info on overfilling the gearbox with oil. Anyone know about how much to use?
@rogeradkins1785
3 жыл бұрын
Good job Warren, would you share what you did with the shaft key way on gear box by the comment you made when talking about the pain it was. I’m doing one on the same order and I’m dealing with the expander collar the 4 different parts that have to fit just right and two keys is a bear right now and I’m open to hear any suggestions you might have in hindsight 😊😡
@firzout
3 жыл бұрын
Can you add a list of the parts you used and where you bought them from? I’m looking at doing the exact same conversion. Great job!! Thanks
@AJay-ki6iu
Жыл бұрын
yeah this would be great !! and would love to know what type of bushing you put bet the torque convertor and the transmission
@brianrosales9085
5 ай бұрын
Did he ever put out a list for the parts
@rodswim492
2 ай бұрын
You did it just like I did but, I found a splined bushing and welded it to a 3/4 " shaft.
@cowcowcheesy
2 жыл бұрын
i would recomend you put a big spring holding the front of the rear engine/axle subfram upward to relieve tension from the leaf springs. i have a similar 212 golf cart build
@Mofm-tl8ov
Ай бұрын
That and maybe a little gas steering stabilizer shock.
@sambaxter9845
3 жыл бұрын
What sort of speed do you get out of the cart? How do you get around the gear down of the forward/ reverse gear back? I am assuming you have it installed backwards to offset the rear end orientation?
@Charles_primetime73
2 жыл бұрын
Whats your top speed with this setup? Love this!
@garyrapsilver1708
3 жыл бұрын
What is supporting the front of the rack that holds the engine and allows it to move w/ rear end?
@shoveshovelson7408
2 жыл бұрын
Warren!!! I used your conversion as a model for mine. Having some issues with the Frame to axel connection. Can I send you my picks/video of where im at? I particularly want to see what you have at the end behind the seat.
@jamesferrell9404
11 ай бұрын
Is it possible to get shaft out without a press? Looking at doing a 125 cc 4 wheeler engine so it will have 3 gears forward and a reverse. Just not sure of best way to hook it to differential. But I like how the block bearing was added on yours
@MrCarmelo1959
3 жыл бұрын
Darn this is awesome but you lacked linking like where to buy that gearbox I also would like to pick your brain on start first day mounting the engine and so on. Very very nice job I would like make mines more quieter bigger muffler?? That would be my preference thanks I really like this I’m subscribing because hopefully you will show the how’s thanks again
@henrygibson2906
3 жыл бұрын
Did you have to modify gearbox? Was there a key way on driven that was fixed? And gearbox was keyway as well?
@vojislavdragic5090
3 жыл бұрын
i got same question about gear box mounting.. i was gonna make new shaft to fit torque converter pulley . but when i took a part gear box , realized shaft had integrated gear .. which would make machining real expensive.. how did you mount it, i would like to know? thanks
@1964hotrodder
4 жыл бұрын
What size sprocket did you use on rearmed and transmission?
@jasonritter2492
3 жыл бұрын
Is that one of the $100 to $150 kit? I ask because I'm getting ready to start my KZitem channel and I'm doing a 1200 Harley Davidson engine swap on my car. I am also doing a Yamaha R1 swap on another. I am gonna do build paint the works start to finish on both. I am also going to do other cool videos.
@BrianBondAudio
4 жыл бұрын
Please update us on how the reverse gearbox is doing!
@BubbaB43
3 жыл бұрын
@Shane Jericho lier's!
@badmudderrutters7460
3 жыл бұрын
How hot does the seat get? Any problems with the underside of the seat burning?
@andresmacias7216
14 күн бұрын
Hi excellent video, how did you relocate the starter switch? is there an extension or we need to cut the wires
@linolozano8897
3 жыл бұрын
Is to 🔥 hot under the seat man
@davidhammond3688
10 ай бұрын
im doing the same thing .. starting it today
@anthonyjoubert8945
2 жыл бұрын
Man I wish you was in Houston I said to you
@jasonbarber1672
4 жыл бұрын
How did you attach your driven to the reverse gear box
@jussomdude9357
Жыл бұрын
Maybe I missed it but was this a electric golf cart at first? I'm getting ready to put that motor in a Chinese electric car and looks like I'll have to do about 95 % exactly how you did...even the removing of the electric motor shaft...can you post about how you got invested in just the motor,gearbox,conversion project? I'm interested in how much I'm going to need....
@davidcastle65
3 жыл бұрын
At least your motor is not surging they are bad about that had to drill jets on both of my 13 horse power motors.
@tomwarren5258
3 жыл бұрын
I wouldn't mind picking your brain a little bit Warren this is Tom Warren
@shoveshovelson7408
Жыл бұрын
Good evening Warren! So I did conversion with the same forward reverse set up you did, including the torque converter directly on the gearbox.... when I go into forward or reverse, I keep breaking the chain. My idle is all the way down... any ideas on a fix or what I screwed up?
@jayjay-il7fk
2 жыл бұрын
How many tooth sprocket did you use for your differential? What size is the stator shaft? IS it 1"? Why didnt you just get a 1" bore sprocket?
@robertbennett6883
3 жыл бұрын
Where did you get the reverse gear box from?
@blowme5150
3 жыл бұрын
Might whant some bushings on that motor
@jameslesswalk
2 жыл бұрын
What all did you have to do to get the pulley onto the gearbox shaft? I have a yamaha g1 and the stock motor is pretty tired I'm thinking of swapping mine but I don't want to lose reverse
@scootersonlyrepair6773
2 жыл бұрын
What's the top speed? Also where did you find the gear on the transaxle shaft
@chinhnguyen-lb3qk
2 жыл бұрын
Where did you get the small sprocket on the differential?
@am_5395
Жыл бұрын
Why does this guy not answer comments😂
@REVNUMANEWBERN
6 ай бұрын
Been through most of these comments & it appears he answers none LOL
@DavidMartinez-uz2vf
3 жыл бұрын
where did you buy the clutch for the preadtor engine... What size is the engine
@tomwarren5258
3 жыл бұрын
What gear oil goes in the forward reverse gearbox
@silentdeath9237
2 жыл бұрын
Driven clutch is backwards so when you rev it up the belt will run crooked.
@MdmTribe
2 жыл бұрын
How's the golf cart going can you make a driving video of it.
@MCscarfacematt
Жыл бұрын
i blew the forwards gear out of my gas yamaha gas cart and with the parts being $680 for an input shaft and the forward gear being discontinued i figured go live axle with this box i got the gear box from ebay said 2-16HP for $172 but theres other videos saying the 420 will break it so im glad to see thats not true for me ill run it if it fails it will only be $172 to replace the whole gearbox the stock transaxle lasted 650km in 3 years no maintenance so i should be good
@royfloydjr.5937
2 жыл бұрын
where did you find the torque converter belt # 203789? I have not been able to find one. what size metal did you use to mount your motor on?
@edgravely1947
Жыл бұрын
Can you send me details on how. You set that gearbox up step by step?
@5PointSlow
2 жыл бұрын
How do you keep it from "clunking" when switch into forward or reverse?
@michaelsmith6491
2 жыл бұрын
Hello how did you hook up throttle cable to gas pedal? Thx
@freedreaming2482
3 жыл бұрын
Wow !
@tomwarren5258
Ай бұрын
How many ounces of oil did you put in the gearbox the second time to make it run right?
@cartsquads47
3 ай бұрын
Do you ever have any issue with the gear box finding neutral while the motor is running? I have this same setup, I have to turn my engine off to get neutral, but i can switch from forward to reverse just fine.
@carlton997
Жыл бұрын
Any videos of the finished product
@dednnishuber7778
10 ай бұрын
Where did you get the clutch for the golf cart
@miguelrivero7204
Жыл бұрын
please answer my comment how did you fit a 40 series twit converter on 30 series reverse gearbox i’m so confused I’m trying to do the same thing to my go kart
@ryancarroll8295
3 жыл бұрын
How fast does it go?
@danv304
2 жыл бұрын
I was thinking of using a wegogas to convert a club car ds from electric to gas. Anyone have any experience with their conversion kit?
@hedgepethracing9590
3 жыл бұрын
Where did you find that gear box??
@Jason-lz6rg
Ай бұрын
Do you have an assembled and driving video of this?
@MadMax-kc8we
Жыл бұрын
Where did you get the gearbox
@coltonupchurch4368
Ай бұрын
How's that electric golf kart you put a harber freight motor on
@DZ-hu2sv
3 жыл бұрын
Is the 300cc motor too small??
@daniol1996
4 ай бұрын
Hi, I’m trying to do the same conversion, but I’m having a difficult time finding the correct sprocket measurement for the shaft, can you tell me what size is the one you used? Thank you
@johnwarren370
3 жыл бұрын
Warren...can you please provide some details on how you used the bushing to enable mounting the 40 series onto the FNR shaft? I am currently doing this mod and I am stuck. Thanks in advance!
@johnwarren370
3 жыл бұрын
Update... I ordered a split bushing with key and it works great to make up the difference in shaft and driven pulley/clutch bore BUT the length of the FNR shaft is the same length as the width of the driven pulley/clutch so there are no visible shaft threads to secure the nut and washer to. Did you have to bore and tap the FNR shaft to secure it the same way the drive pulley is? Any help would be greatly appreciated!!
@riptornsideways
3 жыл бұрын
I really need to find a gearbox for cheap. I'm surprised at how loud yours is even with the muffler. I just have a Chinese shorty header that points down with a small silencer and its about the same loudness as yours.
@coburnlowman
3 жыл бұрын
I just came from eBay. They're $104 with free shipping. That seems much cheaper than the last time I had checked on a reverse buggy gear box. Two orphaned , starved , and cold , pitiful followed me home within the past year. Both are , or usta be electric. Well one would probably still run ok , but the charger is shot , and batteries are swelled up. It was driven to where I picked it up. Anyway I'd rather just have them be gas , that way if they don't work , at least I know what to do to them to get them running on the fly.
@robertm5601
2 жыл бұрын
What gear box you use?
@LEITOAMAYA
6 ай бұрын
where are you located ? how much approx cost to convert the golf cart to gas ?
@jeffmckinnon5690
5 ай бұрын
How do u charge the battery ?
@ryancarroll8295
3 жыл бұрын
How did you mount the driven onto the forward reverse gearbox?
@timbender5296
3 жыл бұрын
With a 5/8" to 3/4" adapter sleeve.
@jhonrojas5102
2 ай бұрын
What transmission do you have? I have a predator 420 and my transmission breaks.
@shawnedegroat4257
Жыл бұрын
Wanna see more videos of it driving
@vincenttorres8363
3 жыл бұрын
Any updates on this?
@joshbaker43
3 жыл бұрын
I threw the stator of the motor into a fire pit and let it cook for about 2 days and all the plates slid right off!
@travisatchley6820
4 жыл бұрын
Where did you get the bushing for the reverse box??
@osnelhdez4430
3 жыл бұрын
Travis did you find out where to get the bushing for the wear box.if you did please let me know
@billyjarvis27
3 жыл бұрын
Where did you get the transmission?
@oflores7457
3 жыл бұрын
Their in Amazon and also gopowersports .com
@tetiny329
4 жыл бұрын
How did u get the motor to move with the rear end .I have a 18 hp duramax on mines and that's the only problem left that I haven't solved
@billyjarvis27
3 жыл бұрын
It’s mounted to the axel
@henrygibson2906
3 жыл бұрын
What size sprocket did you use on differential shaft and gearbox?
@darinpeardon3233
2 жыл бұрын
I got one as well bud I will send you pics if interested
@donaldcampbell7894
2 жыл бұрын
You do know you’re driven clutch is the wrong rotation
@johnwarren370
2 жыл бұрын
The configuration is correct with the red spring per Comet...
@RedneckRepairs
10 ай бұрын
electric to gas is always the right direction to go with a golf cart. A new engine is cheaper than a set of batteries
@themulesheriff3009
8 ай бұрын
He doesn’t seem to answer any questions 😳🤔
@leokashin4387
8 ай бұрын
Добрый день , вы не правильно установил. Ведомый шкив , ремень будет работать на перекос и быстро изнашиваться !
@rodswim492
2 ай бұрын
6:07 6:10 6:11
@gilbertrendon8685
Жыл бұрын
How can I get your number so I can get you to build me one
Пікірлер: 110