Thank you soo much for the NEW float settings. Ive been battling the float level on this DGEV as it has a different looking float bracket. Inverted, the float part kicks up and the tab portion kicks down off the 19mm plane of the pivot pin. It was almost impossible to get 18mm without major bending and forget that 35mm from the float bottom setting. My float was 27mm tall and getting the 35mm to the bottom was only leaving 8mm from the top of the carb! websites are still quoting either 35 from bottom or 18 from top with no supporting data on what float they are using.
@BookAutowerks
6 ай бұрын
Glad it was helpful!
@Engineerd3d
2 жыл бұрын
Definitely useful info. Looking at getting an older carb vehicle. This kind of stuff helps a ton.
@BookAutowerks
2 жыл бұрын
Glad it was helpful!
@TNPTVconnect
Жыл бұрын
Thanks for this video. Very informative. I'm trying to detect the cause of a misfire in my 1979 124 spider 2.0. Perhaps the jets, and also the spark plugs. The car idles differently at different times, I've tuned the carb three times now.
@Mushin-Flowstate
Жыл бұрын
Check spark, fuel, and air first, then move to any Vaccuum lines, then cooling. May help
@Kstxrd
2 жыл бұрын
I envy your knowledge. Well done.
@BookAutowerks
2 жыл бұрын
Thank you! Cheers!
@jefffch
Жыл бұрын
Is your name Tony by any chance?
@BookAutowerks
Жыл бұрын
Are you Ezekiel?
@robertgavigan8191
Жыл бұрын
What do the two hoses of of the intake connect to? Mine has some and idk what to do with em
@أحمدالسعديإسماعيل
2 жыл бұрын
Excuse me, the numbers of all the 1983 Fiat Carbaritier Fiat 131 are 1600.
@nadizahadi1183
Жыл бұрын
Should I swap each other the primary secondary 60 50 on supercharged 1300cc engine?
@BookAutowerks
Жыл бұрын
hmm the supercharger might change things. Best thing to do is get a wideband sensor you can put in your tailpipe and you'll easily be able to see if you need to go larger or smaller on jets. amzn.to/40bXppG
@robertgavigan8191
Жыл бұрын
Where does the hose on the air filter go to?
@BookAutowerks
Жыл бұрын
crankcase breather
@Mushin-Flowstate
8 ай бұрын
Just went to do this, and my tiny little clip is missing lol from the factory
@BookAutowerks
8 ай бұрын
Must have been assembled after having a few glasses of vino at lunch that day 😅
@marekbenes8512
Жыл бұрын
Hello... what jets do you have this carburetor? 32/36 weber Main ... idle... jets ...emulsion tube...air correctors... and pump jet... please
@MichaelAmster
2 жыл бұрын
What did you set the main and air corrector jets to?
@BookAutowerks
2 жыл бұрын
137/140 main jets and 165 air correctors. They come that way from Autoricambi, and most other suppliers.
@MichaelAmster
2 жыл бұрын
@@BookAutowerks I am putting this on a smaller 1438cc, so may go down a step or so on fuel and air.
@أحمدالسعديإسماعيل
2 жыл бұрын
Can I know the speed and air brake numbers, 131, the tan machine, 1600 model 1983
@markbury141
Жыл бұрын
If you took those stupid rubber gloves off you could work better, doing clean work do you really need them? No you don't.
Пікірлер: 25