Two different heads,the valve that is leaking is bigger than one being lapped in!!!
@elcar10
4 ай бұрын
Es la misma tapa , es crosflow . Primero pueba valvula de admision y la que se ve esmerilando es la de escape
@oklahomagoochgrabber7500
4 ай бұрын
He flipped the head over and laped the exhaust valve
@wendellgreenidge3362
4 ай бұрын
First one was an intake valve and second is a exhaust
@user-ct5lg7um4r
4 ай бұрын
Ну впускном клапан
@silentpeer8756
4 ай бұрын
He fliped head and made wideo with exhaust valve insteaod of intake valve
@brenthartzell5531
4 ай бұрын
Ha ha ha. The intake valve was beyond repair. They show it leaking but lap the exhaust valve. 😂
@abdullamamaev
4 ай бұрын
😂😂 что они хотели показать 😂😂😂
@ninoratakingofspam5828
2 ай бұрын
Exelente detalle! 🕶️👍
@user-hg2em2hw4s
4 ай бұрын
Разные клапана показал и доволен😂😂на том впускном седлу совсем печально было А тут выпускной с целым седлом😂😂
@user-zh9bc3ii5f
4 ай бұрын
Они и тот восстановят, не переживай... Эти дети природы во дворе блоки и головки отливают😂
@user-rb3xm9dw7g
4 ай бұрын
Бежал впускной клапан а претирает выпускной , это гениально
@user-in1xx7rs1z
2 ай бұрын
гбц разные вообще, вначале видео и потом
@passokita
4 ай бұрын
When an admissiion valve shifts into an exhaust valve. 🤣🤣🤣🤣
@robertstojcevski1098
4 ай бұрын
How about putting a new valve and seat!!
@matzi9662
4 ай бұрын
That's actual pretty legit. Just the way they do it, is questionable.
@robertstojcevski1098
4 ай бұрын
@@matzi9662 I understand but how long is it going to last?? Not much meat left after machining it
@matzi9662
4 ай бұрын
@@robertstojcevski1098as long as it already lasted and then you have to grind it again. You are only taking away a few thousandth of milimeters of the surface. And you also have to do this with brand new valves or seats. The always have little imperfection themself, which is okay as long as they fit together. And with this methode you fit the valve to the seat to have a perfect sit. That's the reason why you shouldn't swap valves and mount them in the same seat where they original were.
@zelenizub2036
4 ай бұрын
You should know better why not.
@juanhernandez281
4 ай бұрын
Soy mecánico diesel y los que hablan estupideces nunca han reparado un motor diesel ,,eso que hizo está bien!
@babaoreally8220
4 ай бұрын
Testing a pitted intake valve seat,then lapping an exhaust valve seat,probably good already.In the old days we used to lap valve and seat just to clean them up.
@ANDREY2000LEONIDOVICH
4 ай бұрын
Показывает один клапан, притерает другой
@user-it4nu7im1v
2 ай бұрын
I'll see y'all on that American fellas channel when he calls out these numptys
@danb2936
4 ай бұрын
The cup catch was the best thing there 😂😂😂
@lcinformatica92
4 ай бұрын
The only thing of value in this video
@garikdez
4 ай бұрын
To begin with, different valves are shown and perhaps they need to be cut so that there is the correct phase, otherwise the fact that they are not flowing now does not mean that they will not allow gases to pass through.
@defender7746
3 ай бұрын
Powinieneś ryby łowić 😂
@pickle5051
4 ай бұрын
Too aggressive. Chuck the valve itself? Stay brown
@johnstarks5323
3 ай бұрын
If I was over their walking around in steel toes, they would probably laugh me out the town. As they are clearly Flip Flop Mafia.
@enriquemontesdeocafarinas3594
3 ай бұрын
Cuidado con el vástago de válvulas usar manguera entre el taladro y la válvula no arañar el vástago….
@harrycee656
4 ай бұрын
Aside it being a different head. That exhaust valve seat is mangled beyond repair. So now they have a mangled valve also. Clever.
@HRX6.4
3 ай бұрын
Crazy thing is, that’s his drinking water🤣
@j.robertvillarreal5926
4 ай бұрын
I used to do something similar back in the day. Guys would laugh at me. Good work.
@coldgrub6233
2 ай бұрын
I do it this way. It always works.
@joeseda8102
25 күн бұрын
Come on people, BE FAIR! I believe THE POINT of the video is to show a QUICK WAY to DETECT AND FIX leaking valve/seat in cylinder heads. I have used same METHOD many times throughout my 42 year career. You DON'T have to take cylinder heads to machine shop every time to do a simple valve job.
@______-id5ud
2 ай бұрын
I bet those valve guides just love that!
@1RJW381
5 күн бұрын
"RESEAT THE VALVE TO INTAKE (head)"👏🏾📺
@robertsrt
3 ай бұрын
Initial valve leaking was indeed the intake but when they showed the badly damaged valve it was an exhaust. And from there on out all work was done to an exhaust valve.
@stellarv5689
18 күн бұрын
You might want to be careful with valve guides.
@gsent56
24 күн бұрын
This will work for small engines, I've done this for my snow blower and it works well. But anything larger, ply not.
@nopenone9399
3 ай бұрын
Love how they show an intake valve leaking then lap an exhaust valve
@obbiebeal3060
3 ай бұрын
Whooom ! It [ appears ] the head is laying in the same idenical position on the rim it is laying on. One thing for sure, these giys are ready for SHTF .
@deant876
4 ай бұрын
Nice bait and switch. The leaking valve was an intake. But you lapped and tested the exhaust valve
@user-qr2dd9ok9t
4 ай бұрын
Между клапаном и дрелью надо отрезок шланга подходящего поставить, так будет удобнее и мягче!
@muhammadharoonkhan6989
4 ай бұрын
People are not stupid. They can judge what you did. Cheating people is a dirty game. Please delete this video.
@polygoned_cheese
3 ай бұрын
Lol
@letsplaygamesrussia7777
4 ай бұрын
Так нельзя при тирать клапана зразу видно не опытный механик, а еще хуже что кто-то не знающий также будет делать после этого видео
@andrenel7126
4 ай бұрын
Back yard jobs😳🙄
@polygoned_cheese
3 ай бұрын
Lol
@josephward6422
3 ай бұрын
Yep, when he starts spinning the valve with the drill, the valve is bent. Next frame the valve is not bent!
@user-bu6ej7ho2c
4 ай бұрын
А чё разные клапана показали 😂😂😂
@ilyakv7282
2 ай бұрын
Течёт большой выпускной клапан,а точит маленький впускной.😂😂😂
@generalmassive1907
2 ай бұрын
And that, sports fans is how not to do it 😂
@polygoned_cheese
3 ай бұрын
The most amazing thing is when you're good minded and you don't care about haters who would never have the balls to do the same works like you. You start from the very beginning, i know it will work, God bless you.
@Kiwi_Teen-2.0
3 ай бұрын
They were using different engines.
@damienfournier1157
3 ай бұрын
No it doesn't work. A valve seat have two different faces with a sharp angle between. When the seat become worn, it become rounded between those two faces, and the valve also. So if you try to lap the valve on that rounded shape you'll get something that's doesn't leak, but at the temperature of your garage. When your motor will be hot, the rounded shape on the valve won't be in face of the rounded shape of the seat because of heat expansion. It will leak and both will become worn out. If it leak, go remachining the seats and buy new valves. Sorry for m'y " technical " english, I'm French
@danielslaven2828
3 ай бұрын
I don't understand why a mechanic had me get the entire head when he could've done that, and everything would be fine wthf lolol
@harjinderkaurlall314
2 ай бұрын
First of all u shudnt grind valve with valve stem tied in drill bcuz with the weight of drill on other side it can result in wrong seating point of valve or u can lift the machine lil bit to balance. But the best one is to put a piece of lil vaccuum hose(3-4" length)on the valve stem n the other end in the machine chuck. This is how weight won't effect grinding seat.
@user-iy5or7sv9c
2 ай бұрын
Дело не в том, какой клапан, а в том, что дрелью, этого делать нельзя, есле правильно прошарошить, достаточно несколько оборотов, пр. и в лев.... Дрель протирает канаву на клапане, что недопустимо....
@samueltolbert3704
3 ай бұрын
You don't seat valves like this it causing the seats to fall out
@GenaroPatricio
2 ай бұрын
órale que chingones mecanicos
@quicksnipes2393
3 ай бұрын
Abaracadabra.... large valve is now small valve!
@Noeva_GT
2 ай бұрын
You show leak of exhaust valve but you lap intake valve 😅
@staystill6877
2 ай бұрын
Attaching the valve directly to the footer will damage it, then the seal that stands on the valve wont have the proper work because you damaged the body of the valve by attaching the footer directly to it. At least put some rubber and then do it.
@ConstHiperalumina123
3 ай бұрын
Video engañoso, no sabemos si ésa válvula o el asiento estaban perfectos. Se muestra primero, creo, una válvula de escape.
@olegarioc.dagandan7356
2 ай бұрын
It's not a proper way to grind the valve by using hand drill it may ruined the valve guide and the spindle
@glen7463
2 ай бұрын
A how to guide to wear out valve guides
@iyansofyan8541
3 ай бұрын
Resep ningali na....❤❤
@user-ic3ou6vq1b
3 ай бұрын
If only someone could invent some sort of valve seat cutter....
@spontanvideok246
3 ай бұрын
Woow So beautyfull Compression. The best job.👌👌👍👍
@Denzar007
2 ай бұрын
What product do u use to clean the valves
@Jordy-927
4 ай бұрын
You lapped the intake valve so well it became an exhaust Vv.
@johnwadsworth4916
3 ай бұрын
Can't do that with titanium valves
@jeremyfields9801
4 ай бұрын
I have had more problems with my 6.7 then any of my previous trucks ever
@user-oc6wi3tg1h
4 ай бұрын
感恩了解,謝謝分享;
@Ez-tk1xy
4 ай бұрын
Damn another nissan head failure
@ajaygupta99114
4 ай бұрын
Nice video
@e34boat88
3 ай бұрын
nice way to fuck up valve stem holes
@rokybalboa4625
3 ай бұрын
Parabéns, também testamos assim aqui
@georgesam7805
4 ай бұрын
Maybe .........if you were stuck on the side of the road and you had the tools to do this.....even that's a strong maybe
@evgenys5533
4 ай бұрын
Течет большой клапан а притирается маленький 😂
@robertoudokrapf453
Ай бұрын
A 50 anos passados eram bem mais técnicos .
@user-nu5sd5ob1y
2 ай бұрын
Так вообщето не подгоняют . На пружину и со стороны шляпки через резиновый наконечник на дрели
@user-ys5ns5bz8z
3 ай бұрын
Шустрые "напëрсточники", - лохотрон классный.
@bonelesscandy
3 ай бұрын
This is not how you lap valves. Do not put a drill to the valve no real engine builder would do this
@diesel_enduro
3 ай бұрын
This is how americans lapped their valves in the 1930s
@obbiebeal3060
3 ай бұрын
It is not because they do not want the Hgh-Tech tools found in the good old ..... , it is because they are forced to used what they have, because of those globleist who use their power to keep a nation / people in semi-slavery.
@drecarter55
3 ай бұрын
Damn my eyes playing tricks or something he lapped that valve small what magic he knows😂😂😂
@isa_yah_boi_mj
3 ай бұрын
Bro be getting that head😂
@Halle916
3 ай бұрын
Und dann wundern wenn trotz neuer Schaftdichtung Öl verbrannt wird.....😅
@hamoucsc2749
3 ай бұрын
تسلل واضح سيدي الحكم روديت لكبيرة وسيت الصغيرة 😂😂😂
@user-ur2tv3kn3c
4 ай бұрын
Nice work 👍
@user-ns3cs4th9y
3 ай бұрын
Te daré un consejo colócale una manguera a la válvula hasta en taladro para que la vibración no te haga comer le tanto y no quede fugando
@mosestalidong2846
4 ай бұрын
Nice lapping 👍🏻
@faviola9476
3 ай бұрын
No es la misma posicion mostrada😂
@zackcampbell3604
3 ай бұрын
Not even the same valve
@whiteknight1442
3 ай бұрын
Rip valve bushings
@Movil-RepairWrench
3 ай бұрын
My friend did that to a jeep patriot the other day
@michelbesson7750
3 ай бұрын
Vous travaillez bien chef, comme cela que l'on chef, chef
@lcinformatica92
4 ай бұрын
Very dishonest. He machined the valve so much that it grew 😂😂
@Theodor857
4 ай бұрын
Is someone going to tell him that the appy turned the head around and when he came back he lapped the wrong valve seat.
@Yelladog78
Ай бұрын
Nice try
@carlosmoyano6309
2 ай бұрын
No que era con chupon y la pasta carburundum, y a mano? Ese pulido con taladro como que por velocidad, te podrias pasar de pulido es mas, si eres medio mano chueca, recuestas el vastago con la guia y haces mas daño por querer sar mas veloz o vago
@BasitMalik-iq4ud
4 ай бұрын
I think the cnr value set😅😊
@SA-rm9uq
4 ай бұрын
ماهو صحيح اللي كان فيه تسريب كان كبير والأخير صغير كيف كذا !!
@alfonsogaytan1735
4 ай бұрын
Exacto lo que no se debe hacer jejeje no de esa manera ni con taladros lleva asiento válvula guía y capuchón nuevo
@thorstenwunderling658
2 ай бұрын
Pfusch Ventile werden immer von Hand eingeschliffen 😮
@user-xx7hg1zu7b
2 ай бұрын
Das haben wir vor 20 Jahren eh schon so gemacht zur Manta Zeit
@denis8192
4 ай бұрын
Вы не поняли главный секрет! Пастой нужно мазать не седло, а клапан с наружи! Все хейтеры просто притирали не правильно!
@lukeamato423
3 ай бұрын
Never try and lap like this
@_.XxX_.
2 ай бұрын
Фантастика,ёпт! Красава. Умеете. Могёте Просто!
@BetaBeta3301
3 ай бұрын
Так нельзя притирать)
@Baum1000
4 ай бұрын
Fake,niemals bei dem Schaden am Ventilsitzring.Wurde neu gefräst,sieht man auch an der Farbe des Sitzrings nach angeblichen Schleifen. 😂😂😂
@user-id3rl9uz2s
2 ай бұрын
Головки разные то 😂
@HTTss000
Ай бұрын
This is sprint?
@user-gf2kc3bn5m
4 ай бұрын
Thats the way you do it
@robertodomingosdedefreitas5531
2 ай бұрын
Vedação de válvulas ho o mecânico manda pra retifica
@frankguerra3314
3 ай бұрын
Can u do a clip about putting a sleeve in a cinder wall for a sbc vortex
@oettaminovog7963
3 ай бұрын
...scemi noi e le nostre lappature...😂
@oscarwrodriguez7129
4 ай бұрын
Is sad bow, they show a big one and when fixing is small .
@Guanzing
2 ай бұрын
Valve see Kalawang ? Stock over oil lack to hard push of the Bour?
@jeffreychan1559
2 ай бұрын
Different exhaust/or inlet manifold its another scam
Пікірлер: 238