Great video. I noticed you are from my area. Washington. I live in Marysville. Go Hawks and Mariners. Thank you.
@katrinwansing6012
3 жыл бұрын
This is the first video I saw from you and it was reaaaally good! I made two cuttingboards with engraving so far and I want to do more! Your tips were very helpful! Thank you so much! 😊
@SixEightWoodworks
3 жыл бұрын
So appreciate that! Have fun customizing!
@jakejohnson114
3 жыл бұрын
Old Dave 100 is another channel that is all about free hand routing. One of the projects was an epoxy inlay cutting board. Art Resin is an epoxy brand that is food safe that he used.
@tompritch56
3 жыл бұрын
Carbon paper from office supply store works well for transfer. I use all the time to transfer patterns for my carving.
@SixEightWoodworks
3 жыл бұрын
I knew there was something out there!
@maddogshwa
2 жыл бұрын
@@SixEightWoodworks before your time 😉
@welovechoccy
2 жыл бұрын
If you produced a short vid showing how you built your simple yet effective router table, and notated in the video the sizes / dimensions of each piece, I think it would be very much appreciated and utilized / viewed. Also, a short vid showing the simple construction of your 1/4" acrylic base & handles for the trim router would also do very well. The video above is well made, and appreciated, thankyou.
@WoodenItBeGrand
3 жыл бұрын
Another entertaining and informative video. Awesome Work!!!
@SixEightWoodworks
3 жыл бұрын
Thank you so much!
@woodsniffer
Жыл бұрын
Nice video lotsa info and quick thanks for posting .
@jimhargreaves1628
3 жыл бұрын
For your technique with the blue tape underneath, I've you cut out where you're going to carve with a Stanley knife or a scalpel the paper won't kick up. Also found its better to use a smaller bit, so for what you did a 1/4" would be better, hog out the middle first, then go back up to your line remembering to go in the right direction. Good video though, will be subbing!
@derekdodson9982
3 жыл бұрын
Another solid video. Good addition!
@SixEightWoodworks
3 жыл бұрын
Much appreciated!
@chrissullivan2948
3 жыл бұрын
Very informative - well presented, thank you.
@SixEightWoodworks
3 жыл бұрын
Appreciate it!
@stephenmcgeown
3 жыл бұрын
Cool video and great results. Steve Ramsey just posted a short about using the backing of a sheet of labels and printing on that to transfer an image to wood. Worked great and would scale up nicely too.
@SixEightWoodworks
3 жыл бұрын
Great tip for sure!
@TotalBoat
3 жыл бұрын
Awesome tutorial!! The boards came out amazing!
@SixEightWoodworks
3 жыл бұрын
Appreciate all your great products!
@johngregg5735
3 жыл бұрын
Great video! To put the template on - how about blue (or green) tape layer, then the template and then a lyer of clear packing tape. The clear packing tape won't let the template move as you carve. When you're done, peel up the blue (or green) tape and the packing tape comes with it. There's no glue from the packing tape left on the board.
@maddogshwa
2 жыл бұрын
I'm definitely going to try that
@federicomoccia7039
3 жыл бұрын
Complimenti è un bel lavoro, anche elegante
@scrapple8741
2 жыл бұрын
I put clear packing tape over the paper. It tends to keep the paper from ripping out
@Mineboy24157
3 жыл бұрын
Use carbon paper under the template to transfer lines.
@edwinmartinez5075
4 ай бұрын
Is the face shield shatter resistant or impact rated, my safety glasses always fog up
@davidsee3553
3 жыл бұрын
I have a jig that holds the work piece to the wall. Bought this cheap little projector for twenty bucks that projects a piece of paper on the wall. Trace and carve.
@SixEightWoodworks
3 жыл бұрын
Big fan of using a projector. Will have to look into the smaller models.
@Mrwolfpack85
Жыл бұрын
Sorry if I missed it but what wood are you using? Thanks.
@Mjordanlky
3 жыл бұрын
Any tips for not having the epoxy bleed into the surrounding grain? Seems to always happen with my cutting board inlays. Thanks!
@eawoodworking
2 жыл бұрын
Brush on a light coat of clear first. That will seal the grain first. Once that dries, sand it off then put on the died epoxy.
@quadsquadracingable
3 жыл бұрын
Great video and Information! I really like your content! But not sure you catch it but you say uh and um alot! Until I noticed it didn't seem so bad but now I can't unhear it. But don't listen to me just figured I'd let ya know. Still a fan!!
@SixEightWoodworks
3 жыл бұрын
Yeah, it’s such a bad habit and drives me crazy. Working on it!
@quadsquadracingable
3 жыл бұрын
I can definitely tell! Earlier videos it was used alot more. I binged a ton of videos so I had more time than most people. I remember getting reamed by a teacher during an oral book report. I think that's how I noticed it. You're doing awesome man! Wasn't trying to be negative at all!! Keep up the good work!! Go Hawks!
@jessicaparker686
3 жыл бұрын
Another great video! Thank you! Quick question, which version of the epoxy do you use? Slow, medium, or fast?
@travismcpherson9827
2 жыл бұрын
Since he is doing a shallow cut, something like a table top epoxy makes the most since.
@jakeverkuilen1328
Жыл бұрын
Looks great! I've had the issue where after sanding off the excess epoxy that some of the epoxy/pigment leaches into the wood surrounding the engraving in little slivers. Is there something i'm doing wrong? Perhaps a seal coat to prevent?
@SixEightWoodworks
Жыл бұрын
You got it. Flood it with finish before to seal the grain. Otherwise it can definitely get absorbed beyond the engraving.
@jessem5684
3 жыл бұрын
Great video!
@bernieparent9517
3 жыл бұрын
Good information but you said most of us do not have the drum sander so it would have been nice to see you use the hand sander to see how much work it is. The drum sander made short work of cleaning up the epoxy but for those of us beginners how long would it take and what grits would you use with the hand sander?
@SixEightWoodworks
3 жыл бұрын
Here’s a link to when I cleaned it up with that Bosch Sander: instagram.com/reel/CJEbASkj7YB/? Just used some 80 grit and then went through normal grit progression. One board just took a minute with the “turbo” mode.
@BCPOWRIDER420
2 жыл бұрын
Awesome Video.. I only see one thing wrong.. Your Sander is missing a Seattle Kraken sticker..!! Go Kraken..!!
@SixEightWoodworks
2 жыл бұрын
😆 Kraken sticker went up a few months ago! 🦑
@rchavez5056
3 жыл бұрын
Great video. I subscribed to your channel. You can also use carbon paper to trace out the image onto the board. I have been doing that for years.
@SixEightWoodworks
3 жыл бұрын
I knew there was something out there!
@rchavez5056
3 жыл бұрын
@@SixEightWoodworks I have done many signs like you do by free hand. I print the image/logo and then place carbon paper under neath and trace it out with a pen or pencil. You get a really defined line once you remove the carbon paper and image/logo. You should also look into a plunge router so that it makes transitions from letter to letter easier. Keep up the great work.
@marca8881
2 жыл бұрын
What don't do you use? I can't seem to find it
@TheKexsel
3 жыл бұрын
How high do you do with your sanding grits with the inlay? Do you go higher in the epoxy area than the rest of the board? Great video!
@SixEightWoodworks
3 жыл бұрын
I don’t. On a river table, or something with more epoxy I might. But I just stop at 220 or maybe 320.
@TVtime2007
3 жыл бұрын
Have you ever used carbon paper to transfer your design onto the wood. Works well for me. Thanks, David S.
@DonaldSlifer-uk8kj
Жыл бұрын
I have been told by an epoxy expert that clear epoxy is FEA food contact approved. However, once you add pigment it is no longer approved.
@choprpilot76
Жыл бұрын
What final grit do you sand down to before applying whatever finish oil? Does sanding the epoxy dull (whiten) the color?
@SixEightWoodworks
Жыл бұрын
Usually just 220. Some go much higher. Depends on how much epoxy you have. Lots of variables with the epoxy and color over time. Sanding usually doesn’t impact color though.
@larrymays5413
2 жыл бұрын
Hey Nick, Do you have a picture or file for an Everett Police Department Badge, or know someone who might? (working on a Flag)Thanks Larry
@gregj2647
2 жыл бұрын
To what grit do you sand the epoxy to?
@partsdave8943
3 жыл бұрын
Nice!
@SixEightWoodworks
3 жыл бұрын
Thank you!
@sainskomputer4154
2 жыл бұрын
what type of machine and brand of machine , give me complete machine name and model
@richwilson8760
3 жыл бұрын
What Grit sandpaper do you usually run on your drum sander?
@SixEightWoodworks
3 жыл бұрын
I usually keep 80 on all the time
@richwilson8760
3 жыл бұрын
@@SixEightWoodworks I have a lot of nerve problems in one of my arms and sanding is something that just lights it up. I know there’s no way around hand sanding and orbital sanding. However would it be worth it to change the paper during each batch? Maybe 80, 100 & 150 on the drum and orbit then 220 and 300ish orbit only?
@SixEightWoodworks
3 жыл бұрын
I hear you. I’ve had carpal tunnel release surgery and I still have issues. I’ve tried the same thing. But the lines still show if I don’t use the orbital at 80. The Bosch unit made a huge difference though, or a Festool/Mirka.
@ACKSWOODPASTE
3 жыл бұрын
IM curious, are you not concerned that someone could chip off some epoxy and getting that in there mouth, and they make a special epoxy that is food safe. Im always on the look out for videos that could possible do harm just in case you were not aware, not trying to intrude on your video. You boards look great!
@SixEightWoodworks
3 жыл бұрын
Yep, talk about it at the end of the video.
@Zamboni-0805
3 жыл бұрын
What does JME stand for?
@SixEightWoodworks
3 жыл бұрын
It’s for my elementary school I teach at. Gifts for volunteers and retirees.
Пікірлер: 71