I recommend reversing the image. When its done, you can view it through the other side and the clarity is much better, especially if you use edge lighting LED strips. FYI for those asking - Diode lasers won't work on clear acrylic without some treatment because it goes through it.
@ImagR-Laser
Жыл бұрын
The image is correctly mirrored
@nicholascheadle
Жыл бұрын
Have to keep this in mind, just getting started this week myself but looking forward to these a lot. Makes sense viewing the reverse though.
@Tieminminhdiep
Жыл бұрын
I really appreciate it, it's very helpful to me i come from vietnam
@Novoworks
2 жыл бұрын
You really don't want to use isopropyl after cutting with the laser as a common problem is crazing and micro cracking due to the alcohol
@ImagR-Laser
2 жыл бұрын
Wrong, we have a LED light company we run for a living and made over 10000s LED Lamps. The scenario you mentioned NEVER happened. www.eplastics.com/blog/chemical-resistance-acrylic-plexiglass
@Novoworks
2 жыл бұрын
@@ImagR-Laser - Good to hear... but with 7+ years of cutting acrylic with lasers, this is a common issue
@James01520
2 жыл бұрын
@@Novoworks Are you using Cast or Extruded? Big Difference!
@Novoworks
2 жыл бұрын
@@James01520 - Of course Cast
@TOM-yk7bq
2 жыл бұрын
Would a light coat of watered down dish detergent work as well as the alcohol, or better? Ive never used alcohol, but the detergent works great, just rinse under water, no rubbing.
@ImagR-Laser
2 жыл бұрын
I did that before, but it was annoying to wash off all the soap from the acrylics. On alcohol i am way faster, and definitely don‘t get watermarks.
@jazzsheehan
2 жыл бұрын
Hi, Does this technique only work with CO2 or will it also work with diode lasers?
@shellylebeau8412
7 ай бұрын
Did you ever get an answer? I’m curious too.
@jazzsheehan
7 ай бұрын
Sadly no reply
@kimmyh.1731
7 ай бұрын
@@jazzsheehandiode lasers are blue light so this method will not work because the laser light passes right through the acrylic. There are other hacks but all come with trial/error and inconsistencies.
@marvinbrooks2601
Жыл бұрын
Thank you for the lesson
@alanjones-kk4vm
2 жыл бұрын
Could you do the same for Diode lasers please
@AjayKumar-bp2uz
Жыл бұрын
I like your this video It's very help for me Thanku so much
@wijnandbles7623
2 жыл бұрын
Great video
@patdennis4576
Жыл бұрын
Great, I have a photo which comes through to start at 72 dpi but , don’t know why starts also at 1034 mm which I resize to 100 mm width is this increasing the resolution of the photo????? Also the photo, like marriage photos the man is dark and the lady is white what’s best to get an even playing field here? Thanks
@AMariano-v9d
6 ай бұрын
I wish you have the setting for 10w diode laser
@jimking9646
8 ай бұрын
awesome
@SamBatti88
Жыл бұрын
Do you engrave on the face with plastic protection film ? Thank you
@bentebrunsvelt319
2 жыл бұрын
Verry good 👍👍
@randyheinbaugh8238
2 жыл бұрын
thank you
@mclambertlutula3355
Жыл бұрын
I want to engrave a photo on a black tile not painted but black from tile seler, do i need to paint again or just process on ?
@wandersonsouto
5 ай бұрын
Does it work with 10w diode lasers too?
@carlosmanjarrez1809
2 жыл бұрын
How about if I wanted a picture to be done on glowforge for glass??? Can you give me a rundown?
@vinchiecent
Жыл бұрын
for a 130W co2 laser what is the best parameter engraving on that image?
@renjithkr6040
2 жыл бұрын
😍♥️🔥💥
@Сега-м8э
2 жыл бұрын
Здравствуйте, подскажите пожалуйста на какой мощности и скорости производилась гравировка?
@Weltspiele
2 жыл бұрын
Wich errordiffusion do i have to choose? My Laser is asking me: Jarvis, Stucki, or Floyd?
@ImagR-Laser
2 жыл бұрын
ImagR did already the dithering. What software? Probably you should use none of them, something like „passtrough“ available?
@beltramaker
2 жыл бұрын
Good morning considering that you use the same RDWORKS software as mine where do I find the settings you suggest? thank you in advance
@ImagR-Laser
2 жыл бұрын
You mean the step intervall? By double clicking on the layer in the top right, where it says BMP next to it
@beltramaker
2 жыл бұрын
@@ImagR-Laser no i mean invert option is disabled and which option pass through is enabled, i can't find to be able to verify I hope you can help me
@ImagR-Laser
2 жыл бұрын
@@beltramaker these are lightburn settings, rdworks doesn‘t have passtrough or invert :)
@beltramaker
2 жыл бұрын
@@ImagR-Laser ok sorry for the inconvenience, I bought the license and I'm trying to understand how to use it
@ClownfishDepot
2 жыл бұрын
Cool video! May I ask what is the purpose to mirror the image?
@ImagR-Laser
2 жыл бұрын
You‘re actually engraving it on the backside of the acrylic. If you won‘t mirror, it will look wrong after engraving, especially with fonts. If you engrave it on the front you will get a weird parallax effect.
@ClownfishDepot
2 жыл бұрын
@ImagR Thank you very much for the explanation. I did my first test and the mirror one looks a lot better. It actually looks like it has a depth to it. Question for you: I have a Lightburn file but it won't load into imagR. Am I doing something wrong? Thanks 😊
@ImagR-Laser
2 жыл бұрын
@@ClownfishDepot imagr only allows jpg/png/bmp to upload :)
@vinuarikkatarikkat5904
Жыл бұрын
I hve 130w laser so hw can I settle power n speed
@allegiencelies6610
Жыл бұрын
What laser are you using.
@brewacom
2 жыл бұрын
Hi a great video. You have the hand for it! What is the power of your CO2 laser? Greetings and thanks. Walter
@ImagR-Laser
2 жыл бұрын
80W :)
@f4evrgrtful
Жыл бұрын
Where can you purchase the laser?
@miekeverbeek4264
2 жыл бұрын
I can't see it should the air be on or off?
@ImagR-Laser
2 жыл бұрын
I used air assist.
@miekeverbeek4264
2 жыл бұрын
@@ImagR-Laser thank you
@SmithAerosports1
Жыл бұрын
Air on or off when engraving acrylic?
@ImagR-Laser
Жыл бұрын
On
@SmithAerosports1
Жыл бұрын
@@ImagR-Laser This is why I love this channel concise videos very helpful and you respond to comments thank you!
@JONSEREDdotWS
2 жыл бұрын
How do you use the web site without creating an account?
@ImagR-Laser
2 жыл бұрын
Everyone can use the way I shown without an account.
@thatonegamer2709
2 жыл бұрын
Only difference with an account is that is does help the speed up the work abit but thats about it. Or if youre offline that helps also.
@ImagR-Laser
2 жыл бұрын
@@thatonegamer2709 wrong. You have no ads, cleaner design, more algorithms, more features
@brunomasse48
11 ай бұрын
you do noting the laser did it
@Camane53
Жыл бұрын
MISLEADING! The page is free but the images are NOT!
Пікірлер: 60