1) You forget to put the washer back under the ring nut requiring special DT Swiss tool HXTXXX00N5027S. 2) Do NOT use dense grease for the ratchet (probably Motorex 2000 in the video). DT Swiss Special Grease is required (TP-42 + 5%mineral oil), which is even thinner than Sram Butter..
@user-kj9no6xu7b
Жыл бұрын
정말 고맙습니다... 이렇게 상세히 허브 베어링 정비 동영상을 올려 주셔서 전세계에서 최고의 영상 입니다.. 새해 복 많이 받으 십시요 ... 대단히 고맙습니다.....
@thelampire
3 жыл бұрын
There are 28 comments, but nobody mentions that the process you are doing is completely faulty. Once you hit the inner race of the bearing with a hammer, it's scrap. The removal process is spot on, the install process is spot on, but you don't re-grease the bearings after you take them out. You throw them in the trash and put in new ones. You could re-grease the bearings without taking them out, if you really want to do that. (If you have put in some sort of special grease in brand new bearings, I guess that's ok, except for removing it with a blade.)
@quintusblack9112
3 жыл бұрын
The remark is correct, but beside this the entire process was well done. The sharp cutter blade may also cut the rubber sealing, so a better approach is to use a sharp conic tool or a flat and very-very thin screwdriver.
@quintusblack9112
3 жыл бұрын
One can use the bearings that were pull out by using the press but not the one pulled with the hammer removal tool
@cervgda
2 жыл бұрын
Good luck with re-greasing bearing on the drive side (under the ratchet) :D
@andymerrison883
Жыл бұрын
Would you really discard Ceramicspeed bearings at $200 each?? I certainly wouldn't go anywhere near them with a hammer.
@thelampire
Жыл бұрын
Bearings are wear and tear parts, after a while you need to discard them no matter hpw much they cost. Ceramicspeed is a scam anyway, it's only better than the steel high quality bearings in the first 100km. It's quite good for bragging how much money one wasted on something lile a bearing, though.
@dvdwillingtons1266
8 ай бұрын
Thank you very much for this excellent video.
@user-xh6lb6jl4s
2 ай бұрын
非常に参考になりました!
@bikereparo5358
3 жыл бұрын
Parabéns sem falar nada você dia tudo, fiquei seu fã, parabens
@finallap2987
Жыл бұрын
Grazie mille fantastico lavoro 🔝
@Marcelo_Harenza
4 жыл бұрын
Perfect, tools kit complet, show every bearing, others videos show only freehub bearing, the more easy for change.
@renemorale2094
2 жыл бұрын
Exelente tutorial amigo
@jgbarre
4 жыл бұрын
Excellent!
@artgonzalez45
4 ай бұрын
Perfect! Those special tools though.
@hainman1
3 жыл бұрын
Excellent breakdown on the process,im due to do my rear hub,with the ratchet system are the main hub bearings as prone to wear as the freehub ones?would the RRP kit be suffice to press bearings in
@timeriderx
2 жыл бұрын
When I see this much fine work I just want to grease it all up and put it back together and ride! It is not that bad and I live in a very dry climate. So now I will try to get it back together with just new bearings. Cost me $18.00. Oh Well.......
@aleccejkraftcoff5145
Жыл бұрын
Hello! Thank you!
@kyriacosvassiliou9385
4 жыл бұрын
Καλημέρα από Ελλάδα. Πολύ λεπτομερής καθαρισμός, σε εμάς δεν τα κάνουν γιατί είναι χρονοβόρα διαδικασία και αναζητούν το εύκολο χρήμα.
@vivesinpermiso
Ай бұрын
Muchas gracias amigo, me ha sido muy útil 👍👍👍
@brackenlong3732
10 ай бұрын
Amazing i loving it
@jorgemexf
2 жыл бұрын
Goes to deep, the problem is I don't have many tools
@TheGazavman
8 ай бұрын
Wooo nice job !
@gaetanocrispi1271
Жыл бұрын
Super video 👏👏👏👍🔝🔝🔝
@daclown3
2 жыл бұрын
Is that steel bearing or ceramic bearing?
@nyxsplitter7168
6 ай бұрын
Great tutorial video.Can you please share the link for the bearing press tool you use.Many thanks.
@richardjeanneau303
4 жыл бұрын
Hola donde consigo la herramienta para extraer los rodajes del hub? // Hello where do I get the tool to extract the shootings from the hub?
@zach_geale
3 жыл бұрын
Anyone else have to mute the sound at the start of the video, due to their cats freaking out about the crying kitten? Haha 🐱
@simonwarmer8777
4 жыл бұрын
Nice job&vid, but way too much and wrong crease on the ratchets?
@pinoybikers8834
2 жыл бұрын
can you tell me what toolset i need in order to do that?
@BMWPROGRAMMINGJAMAICA
3 жыл бұрын
Yo bro, omit out the seals band the hub wheel turn over faster without the seal rolling resistance.
@ssirany
3 жыл бұрын
what is your gold press bearing tool kit (name brand)
@megearbikeshopd.i.y.2883
3 жыл бұрын
ENDURO
@lo_1
2 ай бұрын
As if the thread ring goes ou easy 😅
@davidecirillo6681
3 жыл бұрын
hello sorry I wanted to ask you but where can I find a press like yours?
@megearbikeshopd.i.y.2883
3 жыл бұрын
The press tool I use is ENDURO or you can buy in many brand. Please see below link for ref . activesport.co/Enduro-BEARING-PRESS-F/-HUBS-AND-BBS th.aliexpress.com/item/32961453060.html
@coverstem
4 жыл бұрын
bearings as the same measures front/rear?
@megearbikeshopd.i.y.2883
4 жыл бұрын
DT Swiss 240 Bearing size 6803 for front hub Bearing size 6802 for free hub body (rear hub) Bearing size 6902 for rear hub
@aynakolzincir3372
3 жыл бұрын
@@megearbikeshopd.i.y.2883 Thank you!
@schnuppich
4 жыл бұрын
Diese Sorte Lager hat eine Schmierfettfüllung, die reicht für die Lebensdauer des Lagers. Man sollte diese besser ersetzten und nicht öffnen.
@HarryPotter-wm3kf
3 жыл бұрын
Why are there first 5 bearings ??? and then even 6 bearings ?? I am confused ???
@megearbikeshopd.i.y.2883
3 жыл бұрын
During cleaning process is included front hub bearings.
@SmileyBoy84
4 ай бұрын
Miau miau
@Joekow888
3 жыл бұрын
Great video! What tools did you use to remove the bearings from the freehub body?
@megearbikeshopd.i.y.2883
3 жыл бұрын
I use enduro bearing extractor (someone call blind hole bearing tool set) to remove the freehub bearing.
@balazsnovak81
3 жыл бұрын
@@megearbikeshopd.i.y.2883 Dear friend, please give more exact details even manufacturer or link to this freehub body bearing removal tool. Thank you in advance!
@megearbikeshopd.i.y.2883
3 жыл бұрын
@@balazsnovak81 please see below link. soshanger.com/ENDURO-sealed-bearing-extractor-kit
@sergeykasparov3860
4 жыл бұрын
what lube are you using? looks good. but you should always use DT swiss special grease for the rachets.
@megearbikeshopd.i.y.2883
4 жыл бұрын
I use Shimano premium grease for all cartridge bearing lubrication and also use for rachets too. Thank you for your advise.
@anastasiospattakos6650
2 жыл бұрын
@@megearbikeshopd.i.y.2883 the premium is still thick for freehub mechanisms. Shimano also has a specific freehub grease, I use this. The colour is more towards the white-yellowish.
@ilyakonovalov3119
4 жыл бұрын
Is this dt swiss tools? Or universal?
@megearbikeshopd.i.y.2883
4 жыл бұрын
All tools in the VDO are universal and some of them is DIY tool
@user-sn7xe3of1l
4 жыл бұрын
give the sizes of large cups(pancakes)
@megearbikeshopd.i.y.2883
4 жыл бұрын
OD 45mm / ID 35mm / H 45mm
@tanks5261
4 жыл бұрын
using a knife not a proper way to open the seal. It will damage the sealing
@megearbikeshopd.i.y.2883
4 жыл бұрын
Thank you for advise.
@edermariosanchez2120
3 жыл бұрын
What are the measurements of the body bearings?
@user-gi8bw6xq1q
3 жыл бұрын
MEGEAR BIKE SHOP D.I.Y. 4 месяца назад DT Swiss 240 Bearing size 6803 for front hub Bearing size 6802 for free hub body (rear hub) Bearing size 6902 for rear hub
@edermariosanchez2120
3 жыл бұрын
@@user-gi8bw6xq1q thanks!
@dangnation5378
2 жыл бұрын
Lol another French mime video with no talking or subtitles.
Пікірлер: 62