I added epoxy "granite" to my Sieg X3 mill and my Toolex drill press. Definitely an improvement and reasonably easy to do. I used a mix of sand and gravel chips and as you've found out there is ton of conflicting information out there on possible combinations of materials. Marine chandlers sell good epoxies.
@robguyatt9602
Жыл бұрын
I like that you wrote "granite". I'm suspect any stone would perform. Crushed granite is expensive.
@DavidHerscher
Жыл бұрын
There’s a company that makes an epoxy granite product specifically for this purpose, filling machine castings. The company is DIAMANT polymer. They are based in Germany, but there is a distributor near me in the states, might be one near you as well. Also, I really enjoy seeing how much you are able to do with limited and small tools. You make the most out of everything at your disposal and that’s just awesome to see, especially in this day and age where we are often so spoiled and take too many things for granted.
@BuildItAnyway
Жыл бұрын
Uhpc works better and is cheaper. Have a look at durfill.
@DavidHerscher
Жыл бұрын
@@BuildItAnyway thanks I’ve not heard of it before but I’ll check it out!
@jimporter
Жыл бұрын
I think an important factor missed here was hi statement about low cost.
@cameronmccreary4758
Жыл бұрын
I've seen a few German machine tools that were deliberately designed from the ground up using epoxy granite. They took most of the vibration out and do a nice job machining parts.
@JackHudler
Жыл бұрын
Yes. To get true vibration dampening using EG, you must design the machine from ground up. By creating vibration isolation areas. That's where true dampening comes from.
@Oberkaptain
Жыл бұрын
Using lead shot for shotgun shells is also a great option.
@VHjykfUuYu
Жыл бұрын
If you want a cheaper, easier and overall better solution to the problem, just take a prefferably polished granite curb (I've used 120x20x8 cm or something like that), drill it, put it under the lathe and bolt the two together. 38 kg of solid granite really does the job.
@lasskinn474
Жыл бұрын
That doesn't go inside the frame though? Could combine i suppose but the thing itself jumping up and down isn't the problem
@VHjykfUuYu
Жыл бұрын
@@lasskinn474 but you're bolting the bed to a "large" mass of stiff material. The granite mass acts as a damper, and provides a stable, solid base to rigidly fix the two feet of the lathe. It ties both ends of the lathe together, which can't be said about epoxy granite. If the lathe's feet are bolted down to plywood(as is the case here), then the bed is poorly supported, which makes the lathe prone to vibration. The granite base made a huge difference in the cut quality due to increased rigidity of the whole assembly. On one hand I don't want to diss the guy, but this improvement comes with more disadvantages than advantages. Mainly: - stupid pits inside the bed, through which chips won't fall through - same stupid pits, which won't let you run coolant, which is great for carbide tools. After some time the nooks and crannies will be filled with goo made from dust, way oil and cutting oil.
@jamesspry3294
Жыл бұрын
Isn't granite very bad on bending stress and liable to crack if you use it like that? Might be better to attach the base of the lathe to steel, and then attach the granite to that? But yes, lots of mass will change the resonant frequency enough to get you away from the danger zone.
@arthurmoore9488
Жыл бұрын
@@VHjykfUuYu I say fill the thing with molten lead! Or aluminum if you don't like toxic heavy metals. Aluminum has about the same density as Grantite, though likely won't be as good at vibration dampening. More inline with this project, you can just add a top coat of paint, and that solves the 2nd issue. The first can be solved by drilling holes, then painting them.
@davidelliott5843
Жыл бұрын
Enough bending to crack the granite would destroy the cast iron it’s irrelevant for this job. Molten lead would demand the lathe bed is heated or you’ll crack the cast iron. I don’t know if lead has useful damping characteristics. Bolting the bed to a heavy steel plate would improve rigidity. A length of railway line (or two) would be properly heavy. Maybe the original bed is just badly designed.
@tinkerer570
Жыл бұрын
Thank you for the video! I was wondering about the same - how to improve rigidity, add mass and maybe dampen vibrations a little. I went a different route and poured myself a 70 kg concrete slab and bolted the lathe to it. Totally worth it.
@squatchhammer7215
Жыл бұрын
I was thinking of making a granite epoxy base. Granted they have found out that granite was a product of mineral grains and a bacterial secretion.
@davidbrinton7173
Жыл бұрын
I used a marble granite slab
@iancraig1951
Жыл бұрын
Good idea
@WilliamBlakers
Жыл бұрын
@@squatchhammer7215 granite a product of bacteria ?
@jacklewis1
Жыл бұрын
I wonder if a concrete paver might be a cheaper alternative, especially for a small lathe.
@dquad
Жыл бұрын
I'd be tempted to do a pure epoxy pour over top of that grit filled surface. Over time you will get some grit coming out and it could abrade your ways.
@autumn5592
Жыл бұрын
I thought the same, but I think there may also be a slight clearance issue, not entirely sure though.
@MrMartinSchou
Жыл бұрын
When listening to the video, I KNOW you're saying "epoxy granite", but I keep hearing it like "places that can be filled with poxy granite", and it makes the video more fun :)
@josecarlospoggian149
Жыл бұрын
Spectacular! Great job,I did pour concrete in a Rong Fu mill column years ago,did help for vibration ,but was messy job I love you idea ! Congrats and thanks a lot for your videos !👏👏👏👏👏👏👏👏👏👏👍👍👍👍👍
@johnj5985
Жыл бұрын
Love seeing all your little upgrades, doo-dads, and tool mods anytime and throughout. It's what precision machining is all about. Carry on!
@MachiningwithJoe
Жыл бұрын
Hey dude great to see you still pushing this lathe to it’s limits and the ideas you come up with for improving the lathe are great. Keep up the good work speak soon.
@MattysWorkshop
Жыл бұрын
Gday, anything added is a bonus, it’s a good thing your prepared to give this a go and see if it does work or not and share the findings, great job mate, cheers
@simonconvey9645
Жыл бұрын
I used #8 lead birdshot and epoxy for a milling machine base. Good results. ( But expensive ). My mini lathe is bolted to a granite slab, about 2 inches thick. It had to be ground / scraped at the feet to work. That was very effective.
@MonticelloSkateTeam
Жыл бұрын
If you have any granite shops nearby, you could try to get a sink cutout for a base. The common kitchen sink in America is 28×16", I used a 30×12" piece for mine, it could be as short as 21.5" from foot to foot. We usually throw sink cutouts in trash, if the guys are cool they will give it to you for free.
@1crazypj
Жыл бұрын
The kitchen counter top people in our area (central Florida - Orlando area) want at least $20.00 for a 'scrap' cutout
@Rubin5342
Жыл бұрын
Half way through - An amazing amount of work you are willing to expend. //ji
@wordwyrd
Жыл бұрын
Just a thought for next time, you can easily use larger granite aggregate generally, and pour the sandblasting media in after, much like concrete.
@oddshot60
Жыл бұрын
I've been considering doing this to fill in the voids in the frame of a 14" Reliant Bandsaw (Delta clone) to increase rigidity for better cuts and mass to soak up vibration. I was thinking of using concrete as a filler, but after your vid, I think epoxy with a filler material might be a better idea. Had you considered using cast iron grindings from brake drums and rotors? You can get as much as you want from an auto repair shop for free. I checked the weight and cast iron grindings are about 125 pounds to cubic foot and aluminum oxide, depending on grade, runs from 60 to 120 pounds. On my band saw I would cut holes 3/4 - 1 inch in each of the webbing in the frame to allow the epoxy to cure as one big piece in the hope of picking up some rigidity in addition to mass.
@samhiscox3511
Жыл бұрын
Cut up tires would work too,, I would think,, pry them in, fill the gaps with silicone. 1st time watching. My thoughts are on a lathe that small positive rake carbide brazed tools 😂would help also. Thanks . ( my bad after watching more videos… those were positive rake, and those issues were addressed….good stuff Maynard)
@scratch_440
Жыл бұрын
That wheel came out great.
@jamesspry3294
Жыл бұрын
Great work mate! You are really inspiring me to get back out into my shed and finish off a few projects...! Helpful formula for you, natural frequency is proportional to the square root of the stiffness over the mass. So if you increase the stiffness the same amount that you increase the mass, it might not do much... But if you increase the mass a LOT, then the stiffness isn't as much of an issue. However, you'll still get the same amount of deflection when you are cutting. (Sigh, no free lunch hey?) Anyway, keep on doing thus stuff, as it's really useful for all of us! Cheers mate 😁
@KarpucMotoring
Жыл бұрын
Thanks for sharing and im sure for those who share after you. Your one of the reasons I got a mini lathe in the first place! Cheers!
@spendymcspendy
Жыл бұрын
Great video! I have been watching lots of videos on epoxy granite and this one is the best! Thanks!
@daveunderwood6498
Жыл бұрын
I have a small mill/lathe combo, and find fixing a 15 lb weight (chunk of railroad track) on the far side of the cross slide works very well. Great video.
@jheurtin1120
Жыл бұрын
Love that ratcheting tap holder.
@forked-lightning
8 ай бұрын
Thanks for the honest review! I have to say I’m not a fan making it so the chips can’t pass through. Why not stay in the direction you went with when adding the enlarged feet and couple the lathe to an inertia base? - -Cast up a 6” thick slab and couple it to the lathe bed. -This should help pull out some resonance and be somewhat easy to reverse when moving equipment if needed you can also get it to significantly heavier than what you can fit inside the machine. -Finally, coupling the two sides of the machine should help increase its torsional rigidity - something your blend of epoxy granite wasn’t designed to do.
@slimjim3229
Жыл бұрын
Interesting. I like the comment about mounting the machine to a slab of granite from a countertop vendor. I finally made larger diameter brass nuts for my QC tool holders. I need to pony up and get the mill.
@wizrom3046
Жыл бұрын
Great video! 👍 And congrats on using the sandblasting garnet as the filler, I had really great results with epoxy-garnet and was one of the first guys to popularise that composite on the CNC forums about 12 or 13 years ago. Actually I think I was the first guy to try garnet. To my taste you had the mix way too dry, it should be wet enough to flow (although slowly) not be like molding sand where you can tamp it into a shape. If anything I prefer to mix it too wet, and let the garnet settle with a lot of vibrating and the epoxy will sit on top to be skimmed off. You can actually get a tighter pack with more total garnet percentage compared to a dryer mix, I know that sounds opposite but the wet mix allows the garnet to sink to the bottom and really interlock the garnet crystals tightly.
@thedave7760
Жыл бұрын
I would have thought depleted Uranium would be the best. If not Lead shot.
@excitedbox5705
Жыл бұрын
Yea that is what I was thinking as well. At least 12-18% by volume which is a lot more than going by weight because the lower density of the epoxy compared to the filler. If you look at the Studer mineral casting videos on youtube you will see that they are pouring it like concrete. Rampf looks to use a slightly drier mix in their video but still enough to flow on it's own.
@wizrom3046
Жыл бұрын
@@excitedbox5705 ... yeah agreed. I would make it even wetter, and it is not a problem because the garnet/stone sits on the bottom and the epoxy makes a layer on top. You can pour off or skim off the excess epoxy and vibrate it to settle, then add more stone (which needs to be pre-wetted) etc. I would say if you dont have even a couple mm of liquid layer on top you made it too dry. It is not cookie dough. Pour it, dont play pat-a-cake.
@thedave7760
Жыл бұрын
@@wizrom3046 Wouldn't lead really help with this? It is one of the densest materials we have and I would think it would mix well with epoxy.
@wizrom3046
Жыл бұрын
@@thedave7760 .. I think the big benefit from the epoxy granite is that it is very hard and rigid, but lead is soft and very bendable. Lead would also be very expensive in large volumes and difficult to work with.
@WeCanDoThatBetter
Жыл бұрын
Really cool! I have this on my list of things to do on my Mini Lathe too :) Interesting to see how you did it. Thanks for sharing this!
@vijaykumardahisaria7325
Жыл бұрын
Beautiful small lathe & I like your work
@DrewTeter
Жыл бұрын
You can increase the packing density by using multiple sizes of filler. Using 3 sizes (large, medium, and fine) is good enough for most purposes, but the relative sizes and proportions matter.
@Thats_Mr_Random_Person_to_you
Жыл бұрын
Great content. I kinda like the iron of saying the paint doesn't stick to well to the casting and then being unable to remove it 😅 based on the location I bet the paint there had absorbed a heap of gease and oils over time and meant the paint stripper was just unable to cut into the paint as the grease... if that was the case, no amount of 'quick' (relative term) cleaning and using a degraser to get the surface grime off would have helped! Great vid again, and thanks for doing the experiment!
@fearlyenrage
6 ай бұрын
intention to inform. I made a pure wooden table for a 80kg SChaublin102 lathe. That dint workout at all. The wood is bouncing up the vibrations. It swings within so to say. I changed to a steelframe and the swinging is gone. Its as simple as it gets as heavier the table is the better is the vibration dampening. I have also a Schaublin 102vm with a 400kg castiron table or sockel. there is almost no vibration unless the cutting parameters are unbalanced. Screw your lathe table to the floor so max rigididy is gained. Is written in the manual btw. ^^ like your clips gained much from them. Thy keep em coming =)
@craigkaschan4822
Жыл бұрын
I am on my 2nd one of those drill presses. Had to return my first because the motor started smoking and lost power after 30 minutes of use. Only drilled about 10 holes. May have been a dud but haven’t used the replacement as yet. Good job as always
@artisanmakes
Жыл бұрын
Yeah from what I've heard some of them are a bit hit or miss.
@TheMadJoker87
Жыл бұрын
dumb question, how about using led pellets instead of garnet or granite? not sure about the dampening vibrations part but it would definitely add a lot more mass. also, as you mentioned, i think the biggest improvement would be to change the wood table for a steel mounted frame, or even concrete
@JackHudler
Жыл бұрын
You could do this. However, lead shot is getting difficult to find in some countries. But don't get me started on the stupidity of lead regulations.
@Dwarfgrinder
Жыл бұрын
I mounted my 10x24 on a 2 inch slab of concrete and filled her up with sand/epoxy. definitely made the machine have better finishes and less chatter.
@Rubin5342
Жыл бұрын
Yup, we agree on the practicality of this. Great video. Thank you //ji
@artisanmakes
Жыл бұрын
Glad you enjoyed the video. Cheers
@tsclly2377
Жыл бұрын
Thanks.. I have a 900mm table top mini lathe that need a lot of upgrades. I think that you could have used granite with the garnet and tried adding food grade silicon dioxide to the resin mix to lower the percent of actual resin and make a more stone like fill. I am on a wood table and am thinking of making a additional base out of 25-10mm metal with a fill to add dampening.
@Kineth1
Жыл бұрын
This is a neat trick for mass-loading equipment. I can see this being helpful for many different machine types. 14:13-14:31 full volume on the cut makes the voiceover hard to understand.
@artisanmakes
Жыл бұрын
Editing mistake I was tired :)
@ScheunenTecCNC
Жыл бұрын
Great Solution for this Tiny Lathe
@bluejayfabrications2216
Жыл бұрын
I used the same drill press motor to made an alloy wheel polisher it's suprisingly good
@courier11sec
Жыл бұрын
I feel like brake lathe dust from your local auto repair might make an excellent medium for filling like this mixed into the epoxy. It would be nearly as good as just filling the voids with cast iron. As always, thank you for sharing your projects with us. 🙂
@helmut666kohl
Жыл бұрын
Thumbs up for the resin comparison! Polyester sure has a very messy smell, but it also shrinks noticeably. Like 5 to 10%. Epoxy still is in the 3-5% range I think. PUR is best with ~1%.
@assassinlexx1993
Жыл бұрын
Clear epoxy and 7 1\2" lead shot is easy to mix up and looks cool too. But will have a lot of weight. After everything is set you can drill holes for coolant drains
@coyotearmory
Жыл бұрын
Not sure how easy it would be to find, but im curious how well mixing lead shot into the mix would work, it would definitely up the weight by a decent amount at the very least.
@_billyk_
Жыл бұрын
In terms of motor mounting - I'd personally add some rubber spacers to the mounts (between the motor and the mounting plate, and also under the bolt heads). Rigid mounting the motor without any dampening will let vibration transfer between the motor and lathe - If you add a soft medium between them, you'll see far less vibration being transferred into the cut As for the epoxy, that's a great idea. I've toyed with the idea of making an epoxy granite bed for my little '6040' CNC for a while but finally settled on a thick aluminium plate instead - Though I may add some mass to the underside, it depends on the space I have. I was going to use aluminium oxide ('blasting grit') just because I can get some from my work for free lol I'd suggest casting an epoxy granite / concrete slab for under the lathe if you wanted to take it a step further -Obviously there's only so far you can take these little machines but any little helps
@keithammleter3824
Жыл бұрын
Nice lathe. I've removed paint from low cost Chinese machines and found a generous layer of factory fitted rust underneath.
@artisanmakes
Жыл бұрын
Had the same thing happen on the cover of my mill. Wasn't too happy about that. Cheers
@termlimit
Жыл бұрын
One more thing you can do is to bolt it down to a piece of granite. I went to a granite supplier and got a small piece large enough for the mini lathe (gave it to me for free) and it was definitely worth it. Great job as always.
@mk6595
Жыл бұрын
Absolutely not. Small lathe beds are easily twisted by bolting them down.
@heybabycometobutthead
Жыл бұрын
@@mk6595 All lathe beds are bolted down.
@rowanwiegel4695
Жыл бұрын
@@mk6595 they just need to be leveled like any other lathe. Bolt them down
@joejoejoejoejoejoe4391
Жыл бұрын
I saw one video, someone was making a CNC machine from scratch, and they used granite gravel, I wondered if you could combine granite gravel with granite powder in the epoxy mix. A few days ago I had the chance to use a BIG Harrison lathe, 4 inch spindle through hole and bolted to a concrete floor, an interesting comparison to a hobby lathe - I won't knock what hobby lathes are, they have to be built to a price and I understand that, but jezz, turning a big casting ( a foot dia) at 400 rpm with ease...
@JackHudler
Жыл бұрын
Make a concrete table top about 50mm thick then anchor the lathe to it. This will add additional mass and stiffening. Careful that you make the surface as flat as possible, or be prepared to shim to remove any bed twist.
@howardosborne8647
Жыл бұрын
Just shim and bed the lathe casting down on metal loaded epoxy compound gets everything connected in a manner that is free from stresses or warping. Several suppliers sell epoxy bedding compounds for the specific purpose of jointing machine castings to their respective base plates to eradicate vibration.
@yankeedoodle7693
Жыл бұрын
I stopped fighting my mini lathe and just bought a 10x22. now I can focus on the work and not the machine.
@1pcfred
Жыл бұрын
Are you offering to buy them a new lathe?
@Bob_Adkins
Жыл бұрын
Garnet was a great choice. It's sharp and heavier than granite, and harder too. Some epoxy cures softer, and some harder but it's hard to know without trying a sample. Since it's a small cavity, I thought of just pouring it full of molten lead, which should be better in some ways.
@jackrichards1863
Жыл бұрын
Don't be tempted to add molten metal to a machine. The heat is not necessarily a positive treatment for the hardness or stiffness?
@RaceriEmil
Жыл бұрын
@@jackrichards1863 Molten lead is not hot enough to affect the hardness of the lathebed in any way.
@DH-xw6jp
Жыл бұрын
I too was thinking about lead. But i was going to go the route of getting a bag of bird shot to epoxy into place.
@1crazypj
Жыл бұрын
@@RaceriEmil I read somewhere molten lead was used for tempering gun springs in 17th to 19th century?
@frontiervirtcharter
Жыл бұрын
Lead sounds even better than what I first thought of, iron filings or bits of scrap cast iron. Lead's high ductility would likely absorb vibration well
@jimzivny1554
Жыл бұрын
Nice upgrade, thanks for sharing
@glennedward2201
Жыл бұрын
Good job. Ive been doing epoxy granite for many years and its always been a worthy addition. It does come down to the quality of your mix. You could’ve used some larger pebbles and quartz, probably some other content. Using just sand will leave it heavy and flexible.
@1pcfred
Жыл бұрын
I was surprised how much using a link belt helped my milling machine out when it came to surface finishes. I wouldn't think a link belt would run smoother than a plain V belt does but somehow they do. Link belts look so cool too. Once you get into them they're addictive. So be warned about that. You'll want to put link belts on everything.
@howardosborne8647
Жыл бұрын
The many benefits of modern day link type belts are very much under rated. Polyurethane link belts make for a great drive train.
@1pcfred
Жыл бұрын
@@howardosborne8647 you have to be careful with link belts. Once you get the taste it is hard to quit.
@goboyz8016
Жыл бұрын
Probably could have added lead shot like bird shot which would have given you some added weight. Great job loved the video.
@greggv8
Жыл бұрын
Put the bed upside down on a mill and cut the bottoms of the feet flat. Get a length of U channel iron and clamp it open side up on the mill. Make sure it doesn't rock before clamping so it won't be twisted. Mill the edges flat. Flip it over and mill the flat side. Now you have a heavy, rigid piece to bolt the lathe bed to. It'll form a box with the bed to resist twist and bending. I used to have two of these 7" lathes and they were not very stiff. I could mount a test indicator to the carriage, put it onto a piece in the chuck and pushing on the headstock with one finger would cause enough deflection for the indicator to show. For mounting to a bench tabs could be welded to the U channel prior to any of the milling. Or mill the outer sides flat and drill holes to bolt lengths of angle iron to the U channel. I didn't do the U channel mod because at the time my mill was a Harbor Freight 12 speed drill-mill AKA "Big Red". I did manage to mill the bottoms of the feet the same amount with some careful repositioning and quite a lot of other modifications got applied.
@philmenzies2477
Жыл бұрын
Neat idea. If you go this route on your mill I would consider electrolysis to remove the paint. I have rebuilt a couple of machines and that takes you back to bare metal with almost zero elbow grease.
@RoseDCLXVI
Жыл бұрын
I wonder if lead shot would be a good fill material considering it's quite dense and you can buy it in fine pellet form.
@TalRohan
Жыл бұрын
interesting upgrade, I think I would have added cast lead bars before the epoxy to add as much density as possible, but then I do have access to a reasonable amount of the stuff. Thanks for sharing
@artisanmakes
Жыл бұрын
Fair enough, that stuff definitely doesn't come cheap
@1pcfred
Жыл бұрын
@@artisanmakes You can get tire weights at a wheel shop. They usually have a drum of them. Though new weights usually aren't lead today. I don't know what they are. They're still pretty heavy but don't melt at the same temperature.
@michaelg4931
Жыл бұрын
@@1pcfred The newer wheel weights are usually mainly zinc.
@1pcfred
Жыл бұрын
@@michaelg4931 is that what it is? I know they don't melt like lead does. I never knew zinc was so heavy. They do float in lead. That's how I fish them out. That and the steel clips on the lead weights. From what I've read wheel weights are all kinds of different crap. I think to make the zinc heavier it is mixed with other things. Including even tungsten. Probably tungsten grinding swarf. Recycling is not always practical.
@michaelg4931
Жыл бұрын
@@1pcfred If there's anything from 'cleaning' the lead pot, you should be able to melt any zinc by raising the temp to about 780 °F / 415 °C and the solids will be something else. I use zinc, aluminum and a pinch of copper to make Zamak 27, or at least something very close to it (72% zinc, 27% aluminum and 1% copper), which has similar uses as cast iron. Wear a respirator and in a well ventilated area as zinc fumes are toxic.
@Engineerd3d
Жыл бұрын
Interesting, I have been planing on doing something very similar on my mini lathe and mini mill. Time will tell. But this is not a bad upgrade.
@hampopper3150
Жыл бұрын
I'm surprised you didn't get a sewing machine servo motor.
@Cjarka_
Жыл бұрын
I've been wondering about epoxy granite lately and thought "why not just use cast iron pieces?" it's heavier than any rock, relatively cheap and easy to get and from the chart you've shown it should be better at absorbing vibrations than sand or what you've used. Also noticed that lead alloys have even better loss coefficient so perhaps filling it with lead pellets would work even better.
@byronhaley1566
Жыл бұрын
It seems to me that #8 or #12 lead shot would have been a good choice to mix with the epoxy.
@alanp3334
Жыл бұрын
Minor quibble, at 14minutes you're trying to speak over the lathe doing a cut on that steel rod, perhaps next time lower the volume on the lathe audio.
@mattphilip4595
Жыл бұрын
This is just an editing mistake that he didn't catch. Not done on purpose.
@laplantamichay
Жыл бұрын
looks like an editing mistake
@jayvincent5330
Жыл бұрын
Wow, how petty...
@alanp3334
Жыл бұрын
I was trying to help, not being petty.
@older-wiser-better
Жыл бұрын
Goodness me, that’s just an editing mistake
@weekendstuff
Жыл бұрын
Thanks for the explanations and summary. Will spent time and money otherwise :-) Weekend Stuff
@Tom-yc8jv
Жыл бұрын
@04:05 Sand blasting would have been a LOT better, to get a surface that will epoxy to stick to it. You can get a hand held sand blaster for 30 dollars.
@Tom-yc8jv
Жыл бұрын
@05:00 Duct tape, just by itself, would have worked as well and with MUCH less work.
@artisanmakes
Жыл бұрын
From experience, resins can dissolve the sticky adhesives in tape since many resins have solvents in them.
@Tom-yc8jv
Жыл бұрын
@@artisanmakes That's fine, it wouldn't get to the adhesive that is holding the tape to the lathe, just the section that is open to the epoxy.
@jerrysanchez5453
Жыл бұрын
You had me at "it's relatively inexpensive"
@icusawme2
Жыл бұрын
Why not use cement/concrete? Thanks for the video!
@bobweiram6321
Жыл бұрын
The trick I figured out for using paint stripper is to thoroughly degrease painted surface. Grease, oils and wax, no matter how thin, is a paint stripper barrier.
@ferrumignis
Жыл бұрын
Also getting industrial paint stripper rather than the useless crap they sell to the public. They removed the methylene chloride some years back and it's never worked well since.
@psykosis101
Жыл бұрын
@@ferrumignis just buy straight DCM at that point
@artisanmakes
Жыл бұрын
I don’t use enough paint stripper to think about it much but it’s interesting that the industrial stuff is different. Cheers
@AdamS-nd5hi
Жыл бұрын
You should buy the next size up machine class and start anew series of upgrading it. I'm certain you could get most places to sponsor the stuff too.
@Rorschach1024
Жыл бұрын
EAR Composites (now owned by 3M) makes a line of vibration dampening urethanes that is shocking how well they work. Not sure if they make a castable version though.
@alan-sk7ky
Жыл бұрын
Am suprised you didn't flow a bit of neat epoxy onto the fill once it had started to tack off to get a nice easy cleaning smooth surface.
@timhall8511
Жыл бұрын
Would casting lead into the voids of the bed, or fine lead shot or power mixed with the epoxy be a viable choice? Genuinely curious.
@pauls5745
Жыл бұрын
I was thinking lead too, and you could mix it in epoxy or fill voids with zinc + lead. may ways to go about it, all good and better than factory as is
@alexanderbrikunov4122
Жыл бұрын
Great idea. of the advantages, a large shrinkage of lead during cooling, the inevitable thermal deformation of the bed, and of course the thermal release of the hardened guides of the bed.
@Larken42
Жыл бұрын
There’s also the health and safety risk of working with 11 kg (≈22 lb) of molten lead. I would like to think that the better solution would be to mix in a percentage of lead shot to the casting to distribute the mass around the epoxy
@ambsquared
Жыл бұрын
I bet the lead shot in the epoxy would be good. Casting lead while not needing a furnace, still a lot of heat to expose the cast iron to. Lead is pretty good for a metal at absorbing vibrations too. With the volume available, could more than double the weight. Of course if it was just weight to add, fill it with tungsten. Found a 4” cube that is over 18kg, but cost is about $4000. At that price, just get a bigger lathe.
@ThePsiclone
Жыл бұрын
I wouldn't expect pouring molten lead into the bed to have a good effect on the bed, 1) the bed isn't going to thank you for all that heat. 2) the bed isn't going to thank you for all that shrinkage when the lead cools down. (if you've ever left a pot of molten lead to solidify, you'll notice there's usually a crater formed in the centre due to the lead shrinking) If you want to make your lathe bed look like a banana, just paint it yellow ;-)
@UncleKennysPlace
23 күн бұрын
I'm turning my minilathe into a dedicated threading machine; I'm filling the headstock with epoxy lead (removing the hi/lo gears).
@chrislee7817
Жыл бұрын
There is an old Irish joke, lost tourists ask for directions. A local says well, to get there I wouldn't start from here! My first lathe was a Hardinge HLV it's 60 years old super accurate, top quality machine. It makes me a better machinist, never had any chatter. Also cost the Same as a mini lathe. Everyday I work on it I feel honoured.
@1pcfred
Жыл бұрын
That's nice if you can get it. There's only so many of those to go around though. You're not going to find them many places either. It's all about availability.
@chrislee7817
Жыл бұрын
@@1pcfred there are more around than you think. Check them out. Where are you based?
@1pcfred
Жыл бұрын
@@chrislee7817 I am out in the middle of the Atlantic ocean in a region known as, "the mid atlantic". There's nothing around here but chickens and soybeans. I'm not too far from Brandon Falls. Though Google Maps has it listed as The Big Fall now. For some reason the landmark has had a recent name change.
@chrislee7817
Жыл бұрын
@@1pcfred The home of Hardinge. ☺ Just a courier away. Us Used Hardinge are much more expensive than UK ones though.
@Mike-ff7ib
Жыл бұрын
Great videos!
@Flying0Dismount
Жыл бұрын
Once you bond the sand in the epoxy, it behaves very differently than loose sand in a cavity which is really what those tables refer to.. The benefit of urethane resin is that it is more elastic than an epoxy and would therefore have better damping coefficient. Another alternative is polyester resin (ie car body/fiberglass resin) which is not as elastic as polyurethane, but better than epoxy...
@AJBtheSuede
Жыл бұрын
As a process development engineer (with limited home-scale tooling experience), I have to say that fundamental misunderstanding has bothered me too. People reading charts and material properties without understanding what they mean (and in what exact circumstance the numbers are valid) will most of the time do more harm than good to the end result. Unfortunately that would include most of the single person source "internet truths" you read :) A composite material is a totally new material, especially if the composite is a stochastic rough mix like a grain/polymer. I think the mix he chose will work very well for the intended purpose :)
@ferrumignis
Жыл бұрын
"epoxy" covers a big range of different material properties, some are extremely hard, others can be quite flexible.
@artisanmakes
Жыл бұрын
That is a very interesting thing to consider. That was a section in a referenced paper about composites and damping but it didn’t touch in ceramics and polymers. Probably for the best that this is more focused on weight addition. One of these days I wouldn’t mind having some sort of test rig to see what materials work best. Cheers
@boblewis5558
Жыл бұрын
Given the cheapness, availability, coefficient of expansion, temperature stability and density of granite aggregate concrete (portland cement type) and the ease with which a mix of fine and medium aggregates can be mixed and "flowed", I'm surprised that a lot more use is not made of concrete in the workshop. This is especially true for DIY projects such as lathe mounts, lathe bases, CNC bases and gantries, mill mounts, bases and actual bodies. Concrete is easy and cheap to produce and mould, can be polished and ground to fine tolerances with a good grinder and is EXCELLENT at damping vibrations through pure density alone, not to mention its internal structure. Is epoxy concrete SO much better to justify the extra expense of the resin over cement and water?
@martinathome296
Жыл бұрын
Even if epoxy is better the cost of 20kg bag of concrete mix at Bunnings means you can add way more mass for much less cost
@artisanmakes
Жыл бұрын
Sure, but the epoxy and garnet will be denser than concrete
@boblewis5558
Жыл бұрын
@@artisanmakes I'll take your word for that but I find it hard to believe garnet is denser than granite or epoxy is denser than the cement/sand in the concrete. 🤔
@TorteTS
Жыл бұрын
Good question and remark!
@boblewis5558
Жыл бұрын
@@artisanmakes did some more research and yup, you're right, I was surprised. Garnet is denser than Granite ... >60% denser. However the price is ridiculous ... Almost as cheap to half fill the central lathe void with gold. If the goals are: 1. To increase mass with highest density product 2. Use an epoxy mix to flow into and fill all the space 3. Maximise efficacy, minimise expense Then filling the void with epoxy & fine steel filings (double the density of garnet!) which are plentiful and FREE‼️ from just about any metal working shop. Had you considered such an epoxy mix? In the maker and hobby space cost is key. I just priced crushed garnet and the amount needed just for my small ML2 Myford I estimate would cost over £200 without the expense of the epoxy! That's a complete non starter.
@doitforthamaytus
Жыл бұрын
You could always use a combination of course(granite) and fine aggregate (garnet)
@davidt8438
4 ай бұрын
I wonder if you saved all of your cast iron chips and mixed those in the epoxy, if it would have given more mass, weight and dampening effect. And they’re free.
@Mister_G
Жыл бұрын
Interesting project - thanks :)
@kylebracht
Жыл бұрын
Why did you not choose to fill in the whole section underneath the lathe bed/ways? Below your aluminum sheet
@oddshot60
Жыл бұрын
Wow ... that would be a lot of weight and, since its below the webbing, the mix would be one piece. I should think that would add a lot to rigidity.
@ferrumignis
Жыл бұрын
As he said in the video it adds very little rigidity.
@raumo123
Жыл бұрын
This was more for mass dampening, had he added more below the webbing and mixed the size of aggregate it would definately make it more rigid.
@6NBERLS
Жыл бұрын
I would have been tempted to look for some barite sand (i.e. barium sulfate). They use this to add weight to the mud used for oil well drilling. They also use it to fill the sandbags used in bench rest rifle shooting. Heavy stuff: the mineral barite. If barite proved too expensive, I would have put #4 lead buckshot in the epoxy.
@artisanmakes
Жыл бұрын
Not too familiar with that type of sand. I’ll have to keep an eye out for it in the future
@BubbleOnPlumb
Жыл бұрын
When I needed to add weight and vibration dampening to my anvil stand, I used lead BB's (bird shot) to fill up a large void in the stand. It worked like a champ. Now the void I filled was totally sealed afterword so there is no chance at all of any of the lead or lead dust getting getting out of the containment space. Completely encapsulating the lead shot in epoxy resin should also serve to prevent lead dust generation as long as there is no chance of routinely abrading or otherwise damaging the epoxy/lead matrix. Keep in mind that lead is toxic and lead poisoning is a thing. You must be very careful and safety minded any time you work with, or around, lead to counter potential exposure risk.
@jeffmanges874
Жыл бұрын
Cover your paint stripper with plastic and let it sit, the plastic traps the Esther’s that act on the paint and greatly improves efficacy.
@MyLonewolf25
Жыл бұрын
you could always bolt it down to a steel slab or granite slab for extra mass
@marcwagner9404
Жыл бұрын
I'm planning on doing it as well but use the same method that granitan do witch is they use 3 different size of media in there epoxy granite ( the do the epoxy granite for studer grinders and meany other grinders that have a epoxy granite base)
@grahameblankley3813
Жыл бұрын
Surely to dampen a lathe of vibrations start by bolting it down on a rigid steel bench bolted to a concrete floor with ajustment to level it, you don't get lathe manufacturers sell lathes with wooden stands, also filling the voids you stop the swarf it will build up on top,🇬🇧👍
@jacob_90s
Жыл бұрын
I feel like using some tungsten cubes to take up the majority of the space, then using epoxy with another filler to take up the remaining space
@frontiervirtcharter
Жыл бұрын
I've seen tungsten powder available on Amazon, but it's kind of pricey
@heartminer5487
Жыл бұрын
If your purpose is to dampen vibration, then loose sand is a few orders of magnitude better than a cured, stiff block of anything, even solid/foamed rubber. What is better is going to be loose iron dust. If you want more rigidity, polyester polymer granite is an equivalent option for 1/3 the cost.
@Sherwin657
Жыл бұрын
get Vevor to sponsor you a hand bandsaw
@jimporter
Жыл бұрын
Instead of using epoxy, could you use a liquid rubber mix which surely would help with dampening?
@Valery_1954
Жыл бұрын
Лучший материал для заполнения - безусадочный бетон с фиброй. Коэффициэнт расширения у него такой же, как у стали и чугуна. Прочность - 600 единиц. Эпоксидная смола усаживается при полимеризации.
@johnrussell6620
Жыл бұрын
Had you considered simple bag concrete? You could even change the included mixed generic rocks with granite pebbles if they weren't already granite if you had wanted to.
@artisanmakes
Жыл бұрын
Looking at the forums, the consensus seemed to be very anti concrete, ranging from it not being good at absorbing vibrations to it not being all that dense.
@Ben.last.name.
Жыл бұрын
Concrete is plenty dense, however not good at dampening vibration. The main issue with concrete though is that it shrinks when it dries, no longer able to make a proper fill or bond on all sides with the filled casting. There are non-shrink concrete bag mixes typically sold as "non shrink grout" but as previously mentioned there are other drawbacks to concrete as a casting filler.
@artisanmakes
Жыл бұрын
I guess it is relative, the garnet is almost twice as dense as concrete. Cheer
@JackHudler
Жыл бұрын
@@artisanmakes you're not absorbing vibration, you're changing the resonate frequency of the machine. EG Machine manufacturers know the speed of sound through EG from empirical testing. This allows them to factor this into the vibration isolation of the design.
@MN-Jim
Күн бұрын
I made products with epoxy, resin, and glass beads, and my experiences. It’s best to mix your film material with your epoxy instead of doing pouring epoxy over filling material. You’re dampening and density will not even at all.
@thiagosanchez4453
Жыл бұрын
I considering build a concrete bench for my lathe, as you trim it accordingly with proper bolt and adhesive epoxy you should get better result, theres no significant mass to dump, the cast itself is kinda of massless
@Alakarr
Жыл бұрын
Does anybody know if anyone has tried pouring lead into these voids? Seems like that would definitely increase the mass and I think it would dampen vibration, especially if you used soft lead.
@ziggysolczaniuk3797
Жыл бұрын
Awesome video could you do a nuther one on how u did the new motor set up
@leerogers6423
Жыл бұрын
If you don't already have a lathe take a moment to consider the upgrades needed to bring this one up to snuff. Your conclusion has to be to save yourself a lot of time and money by getting a bigger better lathe in the first place. Don't get me wrong ,all of the mini lathe upgrade videos on YT are helpful, clever and doable but it's a lot less bother if you don't have to bother.
Пікірлер: 444