2:16 orientation of transistors is inverted, i correct it in off camera to make video short. please be advised to check proper orientation of transistor. Thanks to the person who comment below... ❤️
@rheapagamongan430
Жыл бұрын
May tanung ako boss
@lourdaldenpalay1986
8 ай бұрын
good po, saan maka bili ng power ic epson l360
@wayneslink
8 ай бұрын
@@lourdaldenpalay1986 nasa shopee po
@thanhtrung.productions
3 ай бұрын
Hello, I installed an Epson L310 board to an Epson L300 machine. Unfortunately, the Epson L300 machine's nozzle is short-circuited and the Epson L310 board cannot be started. I measured and replaced 2 transistors A2222 and C6144. When I reinstalled the epson L310 printer (previously it was working normally) but the power light only lit up and then turned off, the mainboard could no longer turn on. When I tested it, 2 transistors A2222 and C6144 continued to fail. What should I do next? Do I have to replace the mainboard driver ic? Thanks!
@LyliaMage
11 ай бұрын
paano po malamn kung shorted ang printer head?
@wayneslink
11 ай бұрын
Pag namatay ang ang printer short ang head, check yung transistor, pag nag beep lahat pins meaning short nga
@CreateIT09
Жыл бұрын
boss pwede ba board ng L220 ilagay sa L360?
@wayneslink
Жыл бұрын
pwdi pero ma usab ang model driver hehe
@tyrellwreleck4226
Жыл бұрын
Kailangan icheck muna lahat ng caps after ma remove ang ic and transistors. Pag mayshort parin, dead board na. Nagshoshort din yung microcontroller nyan. Walang pamalit dyan.
@simpletech3973
4 ай бұрын
Can I power on the printer without head attached to test logic board and power supply?
@wayneslink
4 ай бұрын
Yes you can. But gives you a general error.
@quenchtv5436
6 ай бұрын
Sir syang sana dinyo po ncut yung pag solder kasi baguhan ln po ako any advice po anu po brand name ng transistor for epson l310 and L120? Salamat po
@wayneslink
6 ай бұрын
Same po c6144 at a2222
@quenchtv5436
5 ай бұрын
@@wayneslink salamat sir godbless po 🙏 im wondering kng nagaayos din po ba kayo ng desktop pc
@wayneslink
5 ай бұрын
yes po , cp , laptops etc @@quenchtv5436
@Mrdoualable
Жыл бұрын
Lod pag short ba Ang printhead ano po bang iBang madadamay Kasi d na po nag on Yung printer ko after pinalitan ko Ng printhead
@wayneslink
Жыл бұрын
Mostly yung dalawang transistor at fuse lang. Pero pag natamaan pati power ic sira din
@rizaldylimpiada9359
Жыл бұрын
Paano po sir, pag power nag on pero double red light agad blinking, tapos no movement sa cartridge Ng printer, l360 din. Ty
@wayneslink
Жыл бұрын
Marami ako video jan sir check lang sa channel
@KasivijayEdits
Жыл бұрын
How to purchase the items, pls share the link
@wayneslink
Жыл бұрын
Nasa online lang shopee or lazada
@LyliaMage
11 ай бұрын
ung printer ko po, nag nag flush lang ng printer head, hindi na mag on. May power nman ang power supply ok ang continuity ng on and off switch.
@HoopNewsExtra
7 ай бұрын
shorted
@prrintout
Жыл бұрын
Lods may tanong lang ako sana mabigyang pansin mo. Bali nagshort yung printhead ko nasira yung fuse palagay ko di naman nasira yung power ic at transistor kase may power naman. Ang problema lang nagbiblink yung lahat ng ilaw. Sinubukan ko na gayahin yung mga tutorial sa youtube na lagyan muna ng temporary yung fuse ng lead o copper strip. Pero bakit all lights blinking parin kahit inayos ko na yung fuse. Hindi ko pa inilagay yung bagong printhead sinubukan ko lang muna kung mapapagana ko lang yung kahit scanner lang muna pero ayaw kase all lights blinking parin. Ang tanong ko lods kaya kaya sya nagbiblink kase wala ako nakalagay na printhead? Sana nakaencounter ka na ng ganyang scenario, Sana masagot mo lods SALAMAT NG MARAMI MORE POWER SA CHANNEL MO LODS!
@wayneslink
Жыл бұрын
All lights blinking yan pag walang head naka attached. Maganda kung lagyan mu ng fuse bago ekabit ang new head
@prrintout
Жыл бұрын
@@wayneslink Thank you ng marami lods napakahelpful ng channel mo talaga.. More power sayo lods!
@zeekzeek1621
5 ай бұрын
boss pano kaya un di nag pprint yung color after ko palitan fuse
@wayneslink
5 ай бұрын
Posible short na head nyan. Need replacement
@lmreasytechliving
2 жыл бұрын
Very good! Thanks.
@flordelizaflores2300
Жыл бұрын
Kuya may repair shop ka po?
@wayneslink
Жыл бұрын
Visayas po
@newshanlee647
2 жыл бұрын
Sir anung code ng power IC tapos nung transistor.
@wayneslink
2 жыл бұрын
Ang power ic at transistor nasa mismong pyesa ang code number nya.
@richardsabino9190
2 жыл бұрын
idol san po nakakabili ng power ic at transistor
@wayneslink
2 жыл бұрын
Shopee o lazada lang po
@joeyjonestalibong1602
2 жыл бұрын
saan po nakakabili ng pyesa sir? pahare nman po ng link if meron online. Thanks..
@wayneslink
2 жыл бұрын
Lazada o shopee lang po
@gianfrancobriones
Жыл бұрын
Winash ko printhead at pag on mga 2 mins nag bebeeep at nag off na lang and di na sya nag oon 😂 tapon ko na...
@wayneslink
Жыл бұрын
Haha ayos ah 😂
@gh0sthack3r65
8 ай бұрын
Hi, I found your video on KZitem, and maybe you can help me. 2 weeks ago i brought an procolored a3 dtf printer , L1800 , theoretically i have warranty 3 years, but i live in belgium, and it's difficult with the Chinese. Last week monday my printer arrived, Saturday i installed, and because the glue powder didn't arive, i made only 2 prints , that was ok. I cleaned the head, and power off the printer . Sunday arrived the powder glue from Amazon, and i was ready to make my first t-shirt...but surprise, i started the printer, he makes the head cleaning, and after just powered off , and i was not able anymore to power it on. I paid 3000 euro for printer and own, and i made 2 prints...im not very happy. Can you check this 2 videos please. In this video i check the transistors 1-3 and 2-4 kzitem.info/news/bejne/uq-CzH2oeoyciagsi=Y4o8MjLYbpKTDy0L And in this one is the video, when i started the printer second time, i don't know why i made it , i had the intention to film all the process how i make the first t-shirt, but stops before to be able to do something. kzitem.info/news/bejne/yqmExWqgmJpkqqgsi=ooAlWS_uLFDT_IQY Thank you !
Пікірлер: 46