Instead of shaking the ferric cloride solution (3:30), lay the board -- carefully -- over the solution so as to keep it floating, but upside down. The dissolved copper is heavier and SINKS. For the ink the more stable liquid is also better. You will have it dissolved very quickly in minutes. If your board is too dense it won't sink and you should then use a holder/bracket.
@moonreft
14 жыл бұрын
It is not a ordinary ink-jet cartridge. But indeed the Epson ink jet printers do work. All that is needed is a needle and a empty cart to fill with ink. Take a look at the Epson CD printers on the left to see other models do this work.
@LeonardoRomeroP
14 жыл бұрын
Me gusta ver que esa impresora sirve para algo más que pedir cartuchos cada 15 dias.... Good Job congratulations!
@andrycl
14 жыл бұрын
This is not an ordinary ink-jet printer. The ink will never stick on the cooper side, no mather what you would try. In order to succed you MUST USE A LASER PRINTER. For those with less experience i would recomend the 'press-and-peel' tehnique.
@ignatei
13 жыл бұрын
I've invented a PCB printer which does all the job itself. You don't need all that mixing and ironing, etc.
@Ainshtain
13 жыл бұрын
@mgruber4 I agree with you but you got to admit that the mechanism for mixing is pretty cool
@pufarinu
13 жыл бұрын
bun tutorialul, felicitari
13 жыл бұрын
Sos un GENIO Flaco... hoy por la mañana hice una placa y me puse guantes para agitar la placa... SOS MI IDOLO flaco
@amoldipina
14 жыл бұрын
The ExpressPCB also a excelent software...
@1788731
13 жыл бұрын
E buna metoda imi place."clorura ferica"...
@epineh
14 жыл бұрын
Nice work, and I gotta say that etching agitator is awesome ! :)
@erhanzeynel
13 жыл бұрын
What a detstiny of old rowenta irons. I use mine for toner transfering methode.
@AlienRelics
14 жыл бұрын
@LIiutaio It is a mix of the inks that seem to work best as acid resist.
@JohneyBlue
15 жыл бұрын
great job man!! can u make lines under 10 mils? can u make another video with new pcb , but not shematic, only 5, 8 and 10 mils lines?
@sanosukekursch
13 жыл бұрын
@intterror Isso teria alguma importância naquelas trilhas beeeeeem fininhas de sinal de alta frequência e tal, mas pra esse tipo de trabalho, com as trilhas dessa largura, é indiferente, só só alguns µm a menos.
@johnymerida2110
11 жыл бұрын
Felicitaciones.............
@resystanc3
10 жыл бұрын
BEST Epson promotion :D
@linear2001100
12 жыл бұрын
Your PCB STK4191 Serie is the best
@IronMav
14 жыл бұрын
Hi.. good job there. But when you put the board in the printer does not jam? I can do well with my epson SX100?
@intterror
13 жыл бұрын
não se lixa o cobre! isso retira camada de cobre diminuindo sua condutibilidade!!!
@IndiaJim
13 жыл бұрын
Awesome, have you tied Ammonium Persulphate to etch? Good job
@MichaelKoutroulis
13 жыл бұрын
wich model of epson is it ??? have you made some modifications?? thank you
@frotz661
14 жыл бұрын
What model of Epson printer did you use?
@TheSantiagoperezl
12 жыл бұрын
is the best video I've seen, my question is whether to modify the printer prints directly oh mind, from Venezuela and printer model
@gameover2005
15 жыл бұрын
Hi, I have a question for you. I recently modified an epson stylus color 670 so that it would accept the copper board but no matter what I can't make it to print properly, the ink just gets diffused. I've tried heating / color changing / sanding / acetone and more but the ink just keeps "melting".. I think my problem is the ink that this cartridges use.. What kind of ink are you uysing? Is there any "permanent ink" (as in the permanent sharpies) available to prevent this? Thanks in advance!
@volkerball3
11 жыл бұрын
Did you change anything on the printer except the ink?
@NeilCaulfield
12 жыл бұрын
can u explain what printer ink and paper u used? is it just pigment ink?
@resystanc3
9 жыл бұрын
Sikerült. :) Kb. 5 hónap munka volt, de megérte.
@lespaul49
10 жыл бұрын
What model Epson printer?
@jfmateos
15 жыл бұрын
Amazing, congratulations. Is it a modified/hacked printer or just the original/unmodified one? Are you using normal ink or durabrite?
@fklco
14 жыл бұрын
Frate esti campion !!! Cum Dracu faci sa treaca, cartusele peste placuta si ce cerneala ai in ele de se lipeste de cupru, si cum faci sa reziste la cloruraFe ca io am incercat si se dizolva.. Te rog raspunde-mi ca nu dorm noaptea de curios. Bafta
@Penfold8
13 жыл бұрын
Was this an inkjet or a toner printer?
@T.o.n.y.T.
13 жыл бұрын
Excellent ;-)
@LIiutaio
14 жыл бұрын
Why everybody uses red?
@cayeliblsm
8 жыл бұрын
İst printer normal İnjekt type?
@valyardelean
12 жыл бұрын
cu un epson stylus s22 ar merge? trebuie ceva tus special? merge si tusul de refill?
@TheSantiagoperezl
12 жыл бұрын
es el mejor vídeo que haya visto, mi pregunta es si hay que modificar la impresora oh se imprime directa mente, desde Venezuela y que modelo de impresoras es
@ClaudioArrau
14 жыл бұрын
hey... thats Sprint Layout by ABACOM :P nice software, havent bought it yet
@didaloca
12 жыл бұрын
"Enter your text here."
@itTutorials4You
12 жыл бұрын
Pretty pretty cool :) Btw. what song is it?
@81hugoandres
12 жыл бұрын
La tinta es especial
@AlienRelics
14 жыл бұрын
I love your etching tray, too. Any chance I could convince you to join the Inkjet_PCB_Construction yahoogroup to share how you modified your printer?
@boywithadolphin
13 жыл бұрын
Not wearing gloves when using feric cloride? Bet you get brown fingers soon. It stains like hell. LOL!
Пікірлер: 43