00:00 - Introduction
00:14 - Features
01:32 - Inspection & Function Test
02:30 - Charging & DC Box Details
03:19 - Basic Application Tutorial
03:28 - Picking up a Horizontal Roll
04:08 - Picking up a Vertical Roll
05:32 - Clamp Adjustment Tutorial
06:32 - Additional Options
07:17 - Placing a Roll in both Horizontal & Vertical
07:34 - When Finished with the Equipment
07:50 - Outro & Contact Info
See more on this equipment: www.easylifteq...
Roll Manipulators
Visit Us: www.easylifteqp...
Discover what makes Easy Lift Equipment the industry leader when it comes to dependable ergonomic equipment for lifting, handling, transporting or rotating drums. Contact us today by email at sales@easylifteqpt.com or phone at 800-233-1800.
Easy Lift Equipment DC powered Roll Manipulators are the safe and ergonomic solution for handling large rolls in a wide range of applications. The model seen here features our versatile LRCR clamp for gripping rolls from 20 to 40 inches in diameter and with a max. capacity weighing up to 1000 lbs.
The unique design of our LRCR Clamp allows operators to pick or place rolls in both a vertical or horizontal orientation.
The LRCR Clamp offers 360-degree endless side rotation either left or right. The Single stage mast design provides up to 70” of lift from the floor to the center of the clamp, contingent on equipment configuration. A Two Stage Mast design is available for increased lift heights.
Before using the Roll Manipulator, the operator should perform a visual inspection of the of all the hydraulic lines and fittings to check for any leaks or damage to the equipment from previous use. If any damage is located, contact a supervisor immediately.
Prior to proceeding, you should verify that all control functions are in proper working order. The DC Cabinet also includes a red safety switch for the clamp function to prevent accidental release of an elevated load.
When charging is required ensure the Roll Manipulator is turned off. A polarized heavy gauge extension cord is required, which connects the unit to a wall outlet.
This Roll Manipulator has our DC powered lift system which includes two 12-volt AGM deep cycle batteries which are housed in a closable cabinet with a hydraulic lift motor, internal charger, master disconnect switch, and a ‘gauge-type’ battery discharge indicator. Do not operate the unit while charging or with the extension cord plugged in - doing so could cause damage to the Roll Manipulator. Charging times range between 6 & 8 hours.
The most beneficial feature of this clamp is its ability to clamp and pick up rolls from both a vertical & horizontal orientation. This feature is possible due to the LRCR clamp having a lower fixed arm & an upper hydraulic clamping arm. The lower fixed arm acts as a scoop, allowing the clamp to maneuver a clamping pad underneath a horizontal roll located on a skid or the floor. The hydraulic arm than clamps down securing the roll for rotation or transport.
Only lift the roll to the minimum height needed for proper floor clearance while transporting. Never, under any circumstances should you lift or suspend loads over people.
The larger 16" clamping pads are designed to distribute the clamping pressure on the roll & reduce the potential for damage to the roll material.
The clamping pads are comprised of SBR rubber to provide a durable yet secure non-marking surface to grip the rolls.
Darcor ergonomic casters allow the operator to easily maneuver the fully loaded machine with minimal effort.
When operation is complete, or you plan to step away from the equipment, always engage the step-down floor lock. Leaving the roll manipulator unsecure may allow it to move inadvertently and cause property damage or personal injury.
The lower fixed arm of the LRCR has two position settings which allows the clamp to handle a wide range of roll diameters. The adjustment involves removing two pins with relative ease and sliding the lower fixed clamping arm slightly to the desired setting. Adjusting the lower fixed clamping arm allows for handling rolls from approximately 20” to 36” in diameter (on the lower setting) or 24” to 40” in diameter (on the wider setting).
Roll manipulators are available in an FDA approved metallic gray powder coating as well as full 304 stainless-steel construction. Both include food grade grease, food grade hydraulic fluid, and corrosion resistant lift and rotation chains.
Other additional options available for this model include: the Adjustable Clamping Pressure option, Anti-Drift Brake Motor and, a scale system for verifying weight or performing inventory.
We offer a 30-day trial toward purchase program for first time buyers at 15% of the purchase price.
For more information on our products or to discuss the specifics of your roll handling project, please contact us today!
Негізгі бет ER DC Powered Roll Manipulator with LRCR Clamp - Easy Lift Equipment
Пікірлер