Here are some ways to Fix errors 1. Make sure both the uarts, and the ring buffer is working well. Follow what I did in this video and you should also get the results kzitem.info/news/bejne/knmMmaiNpYSIaHY 2. Sometimes the connection with the ESP is the problem, So test the ESP separately kzitem.info/news/bejne/xp-tk4Kpcp5pfm0 3. If you are stuck at the IP Address part, then use a third device. I mean your phone and ESP should connect to a third device (could be another phone or any router) 4. Mostly the issues are with the Discovery boards, and they are due to some UART connections at the hardware level. So make sure you test the UART using the first point. 5. During Debugging, don't halt the CPU while looking for some string. You will loose the data, and the code will hang there. 6. I spent countless hours in making it work, so You also put some effort before simply commenting that it doesn't work. DEBUG..... It's your strongest weapon. PS: Cutecom is only available in linux. Use any other serial monitor like realter, terraterm, hercules etc
@kiansionglau9581
3 жыл бұрын
thanks! Really appreciate a lot your effort and guide. i change another development is workable...no idea why previous development board run half then stop...
@kiansionglau9581
3 жыл бұрын
Thanks bro, 192.168.1.121 CIPMUX---->OK CIPSERVER---->OK Now Connect to the IP ADRESS Look like is success after i change development board. so i key in 192.168.1.121 to my handphone browser? anyway, my handphone no display. can advise a bit for this?
@Tenisinspector8341
3 жыл бұрын
Could you make a tyutoriyal for using ESP8266 with its SPI/HSPI connections instead of UART?
@prajaktagavandi6058
3 жыл бұрын
Thankyou sir
@shrutiprabhu8622
5 ай бұрын
@@Tenisinspector8341 hello did you get this?
@ControllersTech
4 жыл бұрын
I have used NodeMCU, but i wrote the tutorial in terms of AT commands. So you can use it for all the esp8266 types. Regarding the connection, you can google it. All MCUs have the same connection. Rx of ESP to Tx of MCU, and Tx to Rx. Those, who have errors in the Uart_isr function, like DR or SR registers are not present, replace the Uart_isr code with the one provided in this file controllerstech.com/wp-content/uploads/2020/04/Uart_isr.c
@wp0049830
4 жыл бұрын
I have a NodeMCU, which was already programmed using Arduino IDE for some other application. In that case how do I restore NodeMCU back to its original configuration, so that your program works? Thanks in advance
@ControllersTech
4 жыл бұрын
@@wp0049830 You need to flash the AT firmware. Just google it, there are a lot of tutorials available for it
@danusinungga4839
4 жыл бұрын
bro,where i can download a aplication cutecom for widows? i'm stuck in is this. my program cant run because i dont no the ip for turn on and tur off LED
@ControllersTech
4 жыл бұрын
If cutecom not available then use hercules or realterm.. Or putty in linux
@danusinungga4839
4 жыл бұрын
sorry brow i have a question , why i run in hercules and realterm cant display ip addr? what i wrong the view display the symbol cant be discribe ? i follow your program until end but cannot display ip addr
@eduardodelarosaferrer2205
4 жыл бұрын
This is what we need ! Really practical tutorials. Thanks a lot
@user-zx4rj1gs4c
3 жыл бұрын
thx a lot! I thought, that on stm32f103xESP01 i'll have some problems, but this code's working well, your tutos are exellent!
@Pushpam1995
4 жыл бұрын
I love you channel I was searching someone like you. Your video topic are on mark Please make videos always like this..
@guillermososa91
3 жыл бұрын
Thanks a lot it, works perfect on STM32F401.
@HazinINCI
Жыл бұрын
For STM32F7, I disabled the "Enable the UART Error Interrupt" codes in Ringbuf_init() function and I used the updated version of Uart_isr(...) function. Then, it worked for me. Thanks a lot.
@berlinraj8149
4 ай бұрын
Bro.. can you please help me I'm using STM32F429ZIT6 , Serial Terminal usart1 only communicated with terminal.im using usart1&2, one for PC and 2 for wifi module and i interface with ESP8266-01 wifi module. I did everything like this video. But not worked. Can you Give me some idea?
@ZiclopDevices
3 жыл бұрын
Excellent tuto. Thanks!
@dineshsundarschannel5317
4 жыл бұрын
Great great great. Like to do it now. Thank u sooo much
@milosdewit7562
3 жыл бұрын
Very to the point and useful tutorial!
@michazodak431
4 жыл бұрын
I had problems with short time for which the module was connected to the wifi, the reason was too short times between rx and tx so I have added hal_delays in start() functions and everything is working just fine ;)
@cpodge
3 жыл бұрын
Could you explain where you put the delays please because I have a similar issue
@michazodak431
3 жыл бұрын
@@cpodge I dont have access to the project unfortunately, but as I said it was somewhere in start() function which consists of some methods try before each one - should work then delete 1 by 1 to debug ;)
@cpodge
3 жыл бұрын
@@michazodak431 Thanks, I will try this out! Did this stop your server from responding? I can toggle the LED a few times thenit will not reload the page any more in my web browser and I have to do a hard reset to the board
@michazodak431
3 жыл бұрын
@@cpodge after adding delays, server worked properly I have send some data from environmental sensors and displayed them on server and it didn't crash ;). Everything else was done like in tutorial
@rathanshidling9832
3 жыл бұрын
How can i update paramater, new recipe over dynamically. How to implement using linked list. Over n-number of data.
@mehtaptacir
3 жыл бұрын
Hi! Thank you for your videos. Your tutorial is excellent, can you recommend any sources for beginner such as book
@Electronics_Dreams
3 жыл бұрын
I love you! jajaj saludos desde Argentina!
@bodzio_stawski187
Жыл бұрын
Hi, the tutorial is nice, but I'm having trouble understanding a general thing. In general, a web server can probably be made in many ways. You can use a standalone ESP8266, or ESP32-S, or like you: ESP8266 in combination with STM32 sending AT commands. Question: which variant is generally better when creating a device "from scratch"? Is this guide more suitable for existing STM32 devices "extended" with WiFi functionality provided by the ESP module, or is there simply another reason why the STM32 should be a "master" controller than it would be worth using the ESP module alone?
@ControllersTech
Жыл бұрын
This tutorial just adds the wifi capability to the stm32, Nothing else.. If mcu doesn't matter then there are obviously better alternatives like ESP32 .
@neeravdesai3940
2 жыл бұрын
i flashed AT firmware the project is working perfectly, but after few seconds its gone, i need to press reset again please can you guide me, where to change the code, for that i believe its in ESP8266_HAL.c.
@ARM_TECH
4 жыл бұрын
help ws2812b using stm32
@kiansionglau9581
3 жыл бұрын
From uart said that reseting... then stop. Can you advise?
@ControllersTech
3 жыл бұрын
check pinned comment
@Daronedous
4 жыл бұрын
Thanks for tutorial, I had to make few changes in code because responses from my esp8266 module were slightly different but after all everything worked. The only problem I have is that web server is dying pretty fast after 10/15 secs is this due to the fact ram is getting fullfiled or I made some mistakes? Any ideas how to solve that?
@ControllersTech
4 жыл бұрын
Yeah server times out really fast, but that shouldn't affect the RAM. I have use malloc to allocate the dynamic memory. If u did made some changes, cross check the malloc and free. Maybe you forgot to free some allocated memory and it's adding up with the new allocation
@cpodge
3 жыл бұрын
Hi @Daronedous, did you get a fix for this issue, I have the same problem and cannot solve
@xxgoku7774
3 жыл бұрын
Great video! Could you help? I tryied had problems and I quite not understand how do I send a longer(more than 2048 characters) HTML file through the AT+CIPSEND commands! It always ends in an error or just failing at sending data at some point How should the proceidure be? I also tryied with the UART USB adapater but still got the same results
@anushka.narsima
5 ай бұрын
Can you please make a video for connecting stm32 nucleo with a camera? We've tried it with esp32 and ov7670 but nothings working
@truongtansang7500
4 жыл бұрын
Could you show RFID interface? Thank you!
@vloggermoinhu
4 жыл бұрын
Thank you my idol ! I hope u will help me about MQTT protocol
@Acky0078
2 жыл бұрын
Hi, can you please cover the interfacing with EPS via SPI interface?
@franckciccio8032
2 жыл бұрын
Is there any way to get public ip of esp8266?
@harshitajain4870
2 жыл бұрын
Hi! I had done everything as suggested but yet nothing get on terminal. serial console shows download verified successfully but not getting AT command response on terminal and webserver page is also not showing
@harshitajain4870
2 жыл бұрын
Successfully done😄. Thank you Controllers Tech for this hands on. Kudos to your work✌
@pera0perkan
Жыл бұрын
@@harshitajain4870 Hey, what have you done to fix this problem?
@SravyaTaduthuri
11 ай бұрын
HEY CAN YOU PLEASE TELL ME WHAT HAVE YOU DONE TO FIX THE ISSUE
@ramachandra4316
Жыл бұрын
Nice video, can you also make a video to use ESP32 as client and update firebase ?
@h52684
10 ай бұрын
Can we add more 3 4 leds ?? If yes , please could u guide me ..
@ControllersTech
10 ай бұрын
You need to write the html code for the 4 bottons and their handler. Then follow the same method.
@karmindersingh7709
2 жыл бұрын
YES sir i found that thanku. know i want to know connections of wires of stm with esp board
@ControllersTech
2 жыл бұрын
Read the post where you downloaded the project from
@karmindersingh7709
2 жыл бұрын
@@ControllersTech thanku sir
@karmindersingh7709
2 жыл бұрын
@@ControllersTech i have seen that pic but there is no labels on the respective pins.
@TheGui81
2 жыл бұрын
Hello, could you tell me which part of the code I need to modify (expect the HTML one of course) if I want to add a second Led on the same web page ? Because the "Server_Handle" part seems to be adapted to a single Led because of the presence of "/ledoff" or "/ledon" in the adress. Am I wrong ? And if yes, have you any advice ? Thanks a lot for what you do, Regards.
@ControllersTech
2 жыл бұрын
You can create another pages with /led2off and /led2on.
@berlinraj8149
5 ай бұрын
sir please help me how can i get these 4 library file [ UartRingbuffer_multi.c , ESP8266_HAL.c, UartRingbuffer_multi.h , ESP8266_HAL.h ]@@ControllersTech
@ControllersTech
5 ай бұрын
The link to download the project is in the description of the video.
@neeravdesai3940
2 жыл бұрын
How to add few buttons in html code, and add accordingly the changes in "server_start" and "server_handle" in order to add 2 more Leds and make project scalable, I tried addding buttons in HTML and thought ill add more ("if,else if") for adding more logic for several Leds and also declared /ledoff1.../ledon1 in different variables suchd as LED_ON1 or LED_OFF1.....according to the buttons in HTML and output but im not able to make it scalable {also defined pins as GPIO o/p at IOC file} please help, how do i make it work for 3 Leds?
@triettruongminh1423
3 жыл бұрын
I had made connection and then burn the code to STM32F411 discovery i had received only RESETTING..RESETTING...... at hercules what should i do to get ip addresss, help me thanks
@jaredcox8725
3 жыл бұрын
Did you ever figure this out? I have the same problem. I get stuck on the while(!(Wait_for("AT OK ", wifi_uart)));
@venkateshk.j.117
3 жыл бұрын
I am using stm32f446 but the program stuck at is data available function
@ControllersTech
3 жыл бұрын
First check if the uart ia working properly Remove esp, and Short the Rx and Tx pins for the device uart... Now whatever data you send should come back... Try this
@Tommm077
3 жыл бұрын
How we know the IP Adreess bro?
@RocketsAndDrones
Жыл бұрын
I hope this isn't a dumb question, but where can I find/get the ESP8266_HAL.h library?
@ControllersTech
Жыл бұрын
It's in the inc folder.
@MrMilsic
4 жыл бұрын
Boa tarde, implementei o exemplo para stm32f103 más quando inicializo o /* USER CODE BEGIN 2 */ ESP_Init("xxxxx","xxxxx"); /* USER CODE END 2 */ trava nessa inicialização, tem alguma ideia?
@ControllersTech
4 жыл бұрын
You need to check where the error is. If the firmware on the ESP is different, better try thise At commands first, and than change them if needed
@MrMilsic
4 жыл бұрын
@@ControllersTech o problema está quando chamo a função de escrita da seria - Uart_sendstring("AT+RST ", wifi_uart); não conseguir identificar o erro!
@ControllersTech
4 жыл бұрын
your connection might be the problem. also make sure you have followed the steps properly connect your esp to the computer using ftdi or something and try those commands and see if it is responding to them
@iamamaker7096
3 жыл бұрын
I could not see ip adress from uart said that reseting... reseting....reseting. Can you help me?
@kiansionglau9581
3 жыл бұрын
how u solve it? i also encounter same issue.
@walteralejandrobecerratorr1313
2 жыл бұрын
Hi, I managed to bring the code to the STM32L4xxx, a query, Would the connection be to the Uart1 right? On my board I have the problem that these are free pins not soldered, I can use the Uart3, taking into account that the tx of the ESP8266 goes to the rx of the plate and the rx of the ESP to the tx of the plate, is it correct?
@ControllersTech
2 жыл бұрын
Yes
@frigeshi9003
3 жыл бұрын
where can i get the UartRingbuffer_multi.h and ESP8266_HAL.c file?
@myworldbox
Жыл бұрын
not working wtf
@cyberdientu
6 ай бұрын
Sir, can i use stm32f103c8t6 for this project?
@ControllersTech
6 ай бұрын
Yeah why not.
@oguzhanugurlu6019
4 жыл бұрын
thanks a lot.
@samimd5074
Жыл бұрын
can't find the ESPDataLogger.h and c file
@patelapurva5340
3 жыл бұрын
in that require any program for esp 8266
@neeravdesai3940
2 жыл бұрын
Please provide {"ESP8266_HAL.c" and ''UartRingbuffer_multi.c'' with their header files}its not there even at the site nor at github and also not present in description.
@ControllersTech
2 жыл бұрын
The link to the article is in the description. You can download the entire project from there.
@neeravdesai3940
2 жыл бұрын
@@ControllersTech I checked it only the codes are written over there, there are no ".c" or ".h" file or any sort of library whatsoever please kindly check with it and if possible provide zip files for both{"ESP8266_HAL.c" and its header file/''UartRingbuffer_multi.c and its header file} ive watched this video quite alot of times but i keep getting jumbled in libraries i couldnt go forward .
@ControllersTech
2 жыл бұрын
Here is the tip: Every tutorial website that provides the code, it is mostly located towards the end of the article. Here is the zip file controllerstech.com/wp-content/uploads/2020/08/TUT_ESP8266_WEBSERVER.zip
@muratcayrl9356
4 ай бұрын
It still works?
@vinothkannanr2804
4 жыл бұрын
could you make one video on these without HAL
@neeravdesai3940
2 жыл бұрын
is this for nucleo?
@tamngo3039
3 жыл бұрын
Hello thank for video. Can u tell me your theme CubeIDE ? Its so great
@vikneswaranrajandaran6588
3 жыл бұрын
how to make cutecom serial monitor appear?
@hehejadi7598
4 жыл бұрын
Thanks, but do you know about "error connecting refused" when i connected with esp8266 ?
@ControllersTech
4 жыл бұрын
At what point exactly ? Check with the debugger where the program is getting stuck
@dighuyntran1351
3 жыл бұрын
This code doesn't work on keilC
@meohoang7741
3 жыл бұрын
hi thanks for your video,but i don't understand why do we need to use ringbuffer and you use uart_pc only to display the IP address of ESP,right?please help me,thank you very much.
@ControllersTech
3 жыл бұрын
uart2 is not needed. I just used it for the debugging purpose. For the ring buffer, you need it because you don't know the size of incoming data in the uart
@meohoang7741
3 жыл бұрын
@@ControllersTech thanks but i have a problem, i am not able to receive the ip address hercules screen shows only RESETTING……after that it stops from working.what should i do so that i would be able to receive the ip address and open web page please help me. Thanks in advance
@meohoang7741
3 жыл бұрын
@@ControllersTech hey sir i got that word "Now Connect to the IP ADRESS" but when i connect to the web,it said "ERR_EMPTY_RESPONSE 192.168.1.12 don't send any data".please tell me why.I think the problem is the Basic inclusion.it have a warning "a format string is not a string literal",please help me thanks u so so much.
@meohoang7741
3 жыл бұрын
@@ControllersTech i think the function name Get_after get error ,i can't take the value behind that,can u help me ffix it, please help me,thanks you very much.
@triettruongminh1423
3 жыл бұрын
ông ơi tôi không ra được đại chỉ IP giúp tôi với, cảm ơn :D
@TheJosele6
4 жыл бұрын
Hello, I have problems to see the response on the terminal. I have windows and I am using RealTerm, but no program can recognize my STM32F11E-Discovery such a COM. And I dont know why, If you can help me it would be awesome!! Greetings from Spain!!
@ControllersTech
4 жыл бұрын
Looks like you need to install the st link drivers..
@Mohamed-sd1ql
4 ай бұрын
how did you program esp8266?
@ControllersTech
4 ай бұрын
I did not. It uses the default source code.
@user-bo5dt7gd6r
Жыл бұрын
Can i get an IP from the terminal of cubeide other than cutrcom for linux?
@ControllersTech
Жыл бұрын
You can debug and get the ID in the live expression.
@user-bo5dt7gd6r
Жыл бұрын
Need a new configuration of ESP8266 Nodemcu?
@franckciccio8032
2 жыл бұрын
Excuse me, I don't find the code of ESP8266 on github, could you please publish the link?Thank you in advance
@ControllersTech
2 жыл бұрын
It was never published on github. The link is in the description..
@venkateshk.j.117
3 жыл бұрын
Not possible for me to open webpagr
@serhii3436
3 жыл бұрын
Hi. Please help me. I have undefined reference to `Uart_isr'. And dont to understand what needs to be changed. Since I completely repeated after you
@ControllersTech
3 жыл бұрын
Did you do the step at 04:08
@jiajiewong1058
3 жыл бұрын
@@ControllersTech Yes I did, same problem here
@karmindersingh7709
2 жыл бұрын
ESP8266.h file and other files are not availble when i downloaded the ZIP FILE. please help
@ControllersTech
2 жыл бұрын
check src and inc folders
@franckciccio8032
2 жыл бұрын
Hi, what pins do I have to connect on stm32f4 and esp8266?
@ControllersTech
2 жыл бұрын
Tx with Rx and Rx with Tx
@franckciccio8032
2 жыл бұрын
Thanks❤️
@lukaswang3809
2 жыл бұрын
Thanks, where can I download the zip file
@pankajkande4407
4 жыл бұрын
I have used esp8266-01 it response to AT Command and connect to host but when I am going to open web server it doesn't give response when trying to open server page using IP address.i connected my mobile and esp8266 to same host.
@ControllersTech
4 жыл бұрын
Try connecting both the esp and phone to another wifi Check in the debugger, at which part it is stuck ?
@meohoang7741
3 жыл бұрын
can u fix it please helpme,thanks
@dighuyntran1351
3 жыл бұрын
@@meohoang7741 nó cứ kêu là do mạng, mà t thử chạy webserver khác trên adruino thì vẫn được, mạng t ko vấn đề gì, chắc do code
@amjedghrairi2929
2 жыл бұрын
how to get adresse ip
@karriaravind
3 жыл бұрын
which OS are you using?
@ControllersTech
3 жыл бұрын
i was using manjaro KDE back then
@te1760
3 жыл бұрын
Hi, i use esp8266-01 too. When i connect with ttl converter to wifi module and sent AT commands from serial monitor.i got correct answers. But when i sent AT commands from stm32f4, no answer from wifi modul. Whats the problem? What should i do? do you have offer for me?
@ControllersTech
3 жыл бұрын
Are u using uart ring buffer ?
@te1760
3 жыл бұрын
@@ControllersTech i did your both project but both of them stuck at IsDataAvailable funcktion
@ControllersTech
3 жыл бұрын
Remove esp, and Short the Rx and Tx pins for the device uart... Now whatever data you send should come back... Try this
@te1760
3 жыл бұрын
@@ControllersTech its interesting, looks like i send but rx interrupt doesnt occur. i thought first usart 1 port doesnt work, so i have same board and tried on it. and same rx interrupt doesnt occur. but function is correct. cos i use to send data to serial monitor same function.
@te1760
3 жыл бұрын
@@ControllersTech okay i tried and tx wasnt come back. so i configure another usart and it works. thanks so much
@storymstorym3597
3 жыл бұрын
I had made connection and then burn the code to STM32F407 discovery i had received only RESETTING..RESETTING...... at hercules what should i do to get ip addresss
@meohoang7741
3 жыл бұрын
change uart
@triettruongminh1423
3 жыл бұрын
@@meohoang7741 giúp tôi với ông
@meohoang7741
3 жыл бұрын
@@triettruongminh1423 tôi đổi uart thôi ôg trog bài xài u2 thì ôg xài u1 hoặc 3 thui,tui nhận dc ip mà truy cập cụg ko dc ôg,
@Simotp95
4 жыл бұрын
Why if i want to add an ADC to show on the webserver a sensor value the ADC doesn't work?
@ControllersTech
4 жыл бұрын
Maybe you are not implementing ADC properly.. 🤔
@Simotp95
4 жыл бұрын
@@ControllersTech on MX i add a 12 bit ADC with continous conversion enabled then in the while i start the ADC and i put with the pollforconversion instruction the value on a variable called adc_value but it remains always 0 instead...
@ControllersTech
4 жыл бұрын
Start Poll for conversion Get value Stop
@Simotp95
4 жыл бұрын
@@ControllersTech With Start do you mean start server or start adc?
@ControllersTech
4 жыл бұрын
hal adc start poll for conversion hal adc get value hal adc stop
@widcoshop
4 жыл бұрын
hi again.bro can you make tutorial to make android app and webservr too?
@ControllersTech
4 жыл бұрын
I don't know anything about Android app development. And even if you do want to develop, make some web based one. Which can send the data like any browser does and the code will take care of the rest
@vloggermoinhu
4 жыл бұрын
what the aplication for watch UART
@ControllersTech
4 жыл бұрын
Use realterm or hercules
@truongpham7279
3 жыл бұрын
Thanks a lot! But when I use it with STM32F103C8T6, I can't access to the server with provided IP address. I don't know why.
@truongpham7279
3 жыл бұрын
Oh! And I have a warning with "sprintf (datatosend, Basic_inclusion); " function. It warning: "format string is not a string literal (potentially insecure)" at "Basic_inclusion". But with sprintf(data, ".....", SSID) with the same datatype is not warning.
@meohoang7741
3 жыл бұрын
@@truongpham7279 i have the same problem of you,can u talk a bit more detailed,what i need to do,please help me,thank you very much.
@truongpham7279
3 жыл бұрын
@@meohoang7741 bỏ làm kiểu khác đi ông! Hồi đó làm lỗi xong t đổi hướng
@meohoang7741
3 жыл бұрын
lỗi đó ko fix dc hã,ông làm qua kiêu nào ấy
@truongpham7279
3 жыл бұрын
@@meohoang7741 ukm k đc. T đổi qua làm app inventor kết nối vs thingspeak, r stm32 lấy dữ liệu trên đó về điều khiển. Hoặc dễ hơn là lấy esp kết nối firebase hay thingspeak để lấy dữ liệu về chân nào đó, r stm32 kết nối uart đọc dữ liệu chân esp về r điều khiển ngoại vi cx đc.
@furkanklc5220
4 жыл бұрын
Can I use these codes on Keil?
@ControllersTech
4 жыл бұрын
Yes you can...
@furkanklc5220
4 жыл бұрын
Controllers Tech I wonder that your esp8266 module. Whats the model of it exactly? Also can you share the connections?
@ControllersTech
4 жыл бұрын
Actually it's NodeMCU, but i wrote the tutorial in terms of AT commands. So you can use it for all the esp8266 types. Regarding the connection, you can google it. All MCUs have the same connection. Rx of ESP to Tx of MCU, and Tx to Rx.
@harshitajain4870
2 жыл бұрын
i cant find esp .c .h files in the zip folder. Is someone tell is it in the zip file or i have to write it.
@ControllersTech
2 жыл бұрын
They are in the src and inc folders.. just where i put them during the video
@harshitajain4870
2 жыл бұрын
@@ControllersTech they are not in inc and src folder now please help
@ControllersTech
2 жыл бұрын
@@harshitajain4870 what files are you looking for ?
@harshitajain4870
2 жыл бұрын
@@ControllersTech esp8266.h .c file which is going to copied in inc src folder
@ControllersTech
2 жыл бұрын
@@harshitajain4870 I just downloaded the zip file. The files "esp82766_HAL.c, .h, uartringbuffer.c, .h" all are present there. If you still can't find them, contact on telegram @controllerstech
@jiajiewong1058
3 жыл бұрын
Hello! I have this error: undefined symbol uart_isr (referred from stm32f4xx_hal.o). How do I solve it? thank you:)
@ArunR-zv4qv
2 ай бұрын
you mostly including lib file not teaching that things
@ControllersTech
2 ай бұрын
Read the library file. Its not that hard to understand it. Also I have mentioned all those commands in the video, which I asked to watch before this one.
@aliakbar4068
7 ай бұрын
bro , tnx alot it reall works, but if you are using esp8266 01 module first you need to flash it, it is covered by kzitem.info/news/bejne/roavuZyji5WYd2U this, again tnx alot for your code
Пікірлер: 177