Thank you man, I really thought I broke my dad's garage door. I'm subscribing now
@nicksandtrickssa
24 күн бұрын
@SenzeloMabaso-rt7jn thank you for the comment, much appreciated
@SenzeloMabaso-rt7jn
24 күн бұрын
@@nicksandtrickssa thank you so much for the fix. Truly appreciate it 🙏
@2b.eating
10 ай бұрын
Thanks a lot!!
@nicksandtrickssa
9 ай бұрын
You're welcome!
@nolwazisindie1913
23 күн бұрын
Hello Nick. Please assist. I'm getting a 3/1 error code after my limit set up. What could be the problem?
@nicksandtrickssa
17 күн бұрын
Thank you for the comment, apologies for the late response, a E1 error is PC board related, you have to take it have it repaired at your nearest reseller or get a installer to take it in for repair
@isaacmokoena402
5 ай бұрын
Hi Sir I have error P.Aftet resetting or programming instead of going to exit at the end it goes back to P and does not longer accepts remote after wards.I don't know what to do now
@nicksandtrickssa
5 ай бұрын
Thank you for the comment, after it does the limit setup it will go back to flashing P, then you press exit 2x. It will then go to standby mode and that is when you test it with the remote. Where are you getting stuck?
@JacobMhlambi-lt4lh
5 ай бұрын
Hi sir. I have error code E1 displayed on my garage motor when I try to open the garage.
@nicksandtrickssa
5 ай бұрын
Thank you for the comment Jacob, please take it to the nearest re-seller to have it sent to NICE SA for repair, it's a PCB issue that has to be fixed, or purchase a new board
@azizarichards1002
5 ай бұрын
Hello, I just adjusted my door because the gap was alittle to big on the floor... But now I get the P error when trying to open with the remote button... I then tried to reprogram the remote, I go to r and then b, when I press on my remote it give a number 2 and not number 1 which ma leans successful, can you let me know why that is please?
@nicksandtrickssa
5 ай бұрын
Thank you for the comment, you can only adjust the door by doing the completed limit setup, it will flash P until you complete the limit set and the remotes will also only work once the motor confirms limit setup completed
@azizarichards1002
5 ай бұрын
Thank you so much... It is working now after your comment... Much appreciated
@nicksandtrickssa
5 ай бұрын
@@azizarichards1002 no problem, a like and sub to the Chanel would be greatly appreciated
@ByronLat
9 ай бұрын
Hey Man do you know how to stop the beeping when the power goes off?
@nicksandtrickssa
9 ай бұрын
Thank you for the comment Byron, unfortunately there is only 1way, sperglue in the speaker
@ByronLat
9 ай бұрын
Thanks for the reply, yeah been looking everywhere to try figure out how to do it, would disconnecting the battery help? @@nicksandtrickssa
@nicksandtrickssa
9 ай бұрын
Like I said, only 1 way
@akshaynarshi827
8 ай бұрын
After I set the limits, Im getting a flashing 2 and 3?
@nicksandtrickssa
8 ай бұрын
Thank you for the comment, flashing 2 and 3 is not something I have come across, u certain that's what it's doing, it's not a E and a number maybe?
@akshaynarshi827
8 ай бұрын
@nicksandtricks1849 Apologies it displays E2 when trying to sent the limit.
@nicksandtrickssa
8 ай бұрын
I believe E2 is an obstruction during the setup process, clear the obstruction to continue... Have a look at the door for physical issues
Пікірлер: 23