Shouldn't it be 0.48 kV instead of 480 kV at 33:09 ?
@ETAPsoftware
5 жыл бұрын
Thank you for your interest in ETAP Software and thank you for your feedback. Yes, you are correct. The Max kV should be 0.48. This will not have an impact on the final HA study results. This values is only used for equipment evaluation purposes. Thanks for pointing this out.
@rabinshakya1041
6 жыл бұрын
I am using etap V12.6 and i could not find the part to add harmonics to inverter or wind turbine. How can this be done in this version
@hhhgdgb5205
4 жыл бұрын
Nice presentation
@ETAPsoftware
3 жыл бұрын
Thank you for your interest in ETAP Software and your positive feedback
@scylam1
2 жыл бұрын
Thanks for the great video. May I ask if AHF can be added into the system to perform result simulation? And capacitor banks with / without inductors to simulate possible resonance scenario?
@ETAPsoftware
2 жыл бұрын
Thank you for your interest in ETAP Solutions. Please go to our 24/7 Help Center, helpcenter.etap.com for more assistance, or contact your local ETAP office etap.com/offices
@pelinfidan9413
6 жыл бұрын
Thanks for the tutorial but I have a question about the report. I want to see current harmonics at the point of common coupling but the report shows only the voltage harmonics of the buses. So how can I see the individual current harmonics in the report?
@FebriantLeocesio
6 жыл бұрын
Pelin Fidan I have the same problem now. did you find the solution already?
@JuanPerez-zx6cq
5 жыл бұрын
@@FebriantLeocesio just put a very low impedance between your circuit and the grid, then on the harmonic load flow select to plot the harmonic currents in that impedance.
@Charlie7_5v
3 жыл бұрын
I really liked the video, I already subscribed. It helped me a lot. Could you help me with a video on how to design a non-linear load? Please.
@ETAPsoftware
3 жыл бұрын
Thank you for your interest in ETAP Software and your positive feedback, please contact our Technical Support at helpcenter.etap.com/ or one of our offices in your region.
@andrewcooper2479
5 жыл бұрын
It concerns me that when you add a harmonic source and enter the magnitudes of each harmonic order you make no mention under what conditions (e.g. short circuit power / impedance of the mains supply) that those magnitudes should be entered. The magnitudes of the harmonic currents of a 6 pulse VSD for example will be very different depending on the impedance of the mains supply that the VSD is connected to. If the ETAP software does not define under what conditions the magnitudes of the harmonic currents should be entered, how can it accurately calculate the resulting THDi and THDv at the PCC? If the ETAP software does not know the conditions under which the magnitudes of the harmonic currents were entered how does it calculate the change in these magnitudes based on the characteristics (e.g. short circuit power / impedance) of the circuit being modelled in the software?
@ETAPsoftware
3 жыл бұрын
Thank you for your interest in ETAP Software, please contact our Technical Support at helpcenter.etap.com/ for more information
@andrewcooper2479
3 жыл бұрын
@@ETAPsoftware Wow it took 2 years for a reply and even then I did get an answer but instead just instructed to contact ETAP technical support. Why can’t you get technical support to answer my question here for everyone interested in your software to see?
@wongsabarchannel1335
4 жыл бұрын
Hi, Can ETAP used to simulate Transient Stability because of Arc Furnace and its impact of negative sequence which is presenting to Generator?
@ETAPsoftware
3 жыл бұрын
Thank you for your interest in ETAP Software, please contact our Technical Support at helpcenter.etap.com/ for more information
@engcoofletube250
5 жыл бұрын
Tanks for you effort
@ETAPsoftware
3 жыл бұрын
Thank you for your interest in ETAP Software and your positive feedback
@Farhadk1989
5 жыл бұрын
How can you add line reactor to the model. I used the current limiting reactor, but I don't think that's the right one. I need to add a 3% line reactor on a 460V 100 hp motor with a 6 pulse VFD.
@ETAPsoftware
3 жыл бұрын
Thank you for your interest in ETAP Software, please contact our Technical Support at helpcenter.etap.com/ for more information
@jackbayu555
6 жыл бұрын
Why do triplen harmonics does not shows up in the simulation?
@justinp.s9941
5 жыл бұрын
did u had known to display triplen harmonics?
@lyamineboukari2505
4 жыл бұрын
Only 5th, 7th, 11th and 13th harmonic orders are generated from the harmonic source used (the inverter).
@grapegh0stx
3 жыл бұрын
Good day, I am trying to figure out why significant VTHD drop when it passes through the transformer? from 7.29% to 1.27% VTHD as far as i know, only triplen harmonics gets stuck on delta side of the transformer and 5,7,11,13th etc should still be reflected in the primary side? thank you.
@ETAPsoftware
3 жыл бұрын
Thank you for your interest in ETAP. Please contact our technical support at support@etap.com, or open a ticket in our 24/7 online Help Center https:/helpcenter.etap.com
@phasorsystems6873
4 жыл бұрын
Create some circuits! Get to androidcircuitsolver on google
@alexl.9432
6 жыл бұрын
BOOK: POWER SYSTEM HARMONICS AND PASSIVE FILTER DESIGNS J.C. DAS DOWNLOAD FREE: mundoemorendedordigital.blogspot.com/p/power-system-harmonics-and-passive.html
Пікірлер: 28