Appreciate how you have a whole library of content on how to care for your equipment.
@1Cast1Fish
Жыл бұрын
I try my best to take care of things and keep them maintained...just sooooooo expensive to get anything fixed anymore
@omcbob37
3 ай бұрын
Both of my local Evinrude dealers have quit servicing Evinrude motors and carrying BRP parts or service items, so I've switched to Lucas Marine Grease with great results - stays in place as well as Triple Guard grease and I can also use the Lucas grease on the trailer wheel bearings.
@1Cast1Fish
2 ай бұрын
I used the Lucas on my old boat for the same reason...it was simpler to use 1 grease vs 2.
@xtcamaro2668
16 күн бұрын
Your videos are the best! So concise and informative. It also doesn't hurt that you have the same exact engine as I do. : D Thank you so much for your contributions.
@1Cast1Fish
13 күн бұрын
Definitely helps to have the same engine...lol I love mine
@3DOutdoors
Жыл бұрын
Excellent information.
@1Cast1Fish
Жыл бұрын
Thanks for watching!
@thomasbm1
4 ай бұрын
Dont forget to add grease to your exhaust valve, have to remove lower plastic covers. Its on port side if engine. Just did on my 2014 E-tec 115 HO. Also had to replace my actuator motor but luckily the exhaust valve was not stuck due to someone else had applied grease earlier 😇
@1Cast1Fish
4 ай бұрын
Correct on the lower HP motors...the 150 does not have this.
@rcg5334
9 ай бұрын
Great tutorial! Congratulations fron Spain! 👍
@1Cast1Fish
9 ай бұрын
Thanks! 😃 Awesome to see a comment from Spain
@rcg5334
9 ай бұрын
@@1Cast1Fish yes Sir, I have got a little Evinrude E TEC 50hp and I'm learning about It seeing your videos. Thanks a lot.
@steveleston1848
22 күн бұрын
another excellent video. btw your fuel line is contacting the steering ram don't let it wear a hole in line.
@1Cast1Fish
22 күн бұрын
I will have to check it out...I did have to some rubbing on the main power wires under the cowl that needed a bit of added protection early on. Glad you enjoyed the videos...thank you
@trcass1
Жыл бұрын
great tutorial. appreciate the share.
@1Cast1Fish
Жыл бұрын
Glad it was helpful!
@JohnAmes
Жыл бұрын
some great information my friend
@1Cast1Fish
Жыл бұрын
Thanks for watching
@wjstewdog
8 ай бұрын
great vid
@1Cast1Fish
8 ай бұрын
Thank You :)
@lorysproxton8506
3 ай бұрын
Any marine grease will work fine and cost you about a quarter as much
@1Cast1Fish
3 ай бұрын
It lasts a long time, so I have just kept with the same stuff that was original.
@akosguzsik6935
5 ай бұрын
What grease gun do you need for the job and with what fitting ? I try to figure it out but the manuel doesn’t tell me.
@1Cast1Fish
5 ай бұрын
It is a ZERK type fitting. I used a full size grease gun with flexible hose and ZERK attachment.
@user-mq7lx9sp2o
10 ай бұрын
How does grease get to the upper bushing on the swivel bracket or steering arm assy?
@1Cast1Fish
10 ай бұрын
Not sure it's exact route, but I normally see some new grease when I am pumping in the new...so it gets there
Пікірлер: 28