Thanks. I’m not sure why the sound is in mono only 🤔. Unfortunately since I’m deaf in my right ear I didn’t notice in editing 🤬. Skäl. David
@felakawilam5747
5 жыл бұрын
Fine with meee
@Thulldai
4 жыл бұрын
Yup, i thought the right side of my earphone stopped working😆😆😆
@XNK--C
4 жыл бұрын
@@Thulldai same 😬
@MotoMirius
4 жыл бұрын
It’s just to test who is paying attention 🤔
@bvkstha4944
3 жыл бұрын
I love the stock silencer of the new KTM duke 200, 250 & 390. It's looks so good.
@MotoMirius
3 жыл бұрын
Stock silencers are pretty good quality, so if you like them, then no reason to change.
@codymouret
4 жыл бұрын
38mm worked as that was all I could find at the local hardware store. Also when cutting, after a few minutes the cutting will change from smooth to getting caught up on jagged edges. this indicates you have cut thru the material. Carefully proceeding to cut until only a little material is hanging on, use pliers and work it until loose and no worries about fishing it out or large amounts of metal shavings getting in the exhaust.
@MotoMirius
4 жыл бұрын
38mm can be difficult if there are large welds. Glad you got it through ok and great advice 👍. Skäl. David
@carlos-cj2862
Жыл бұрын
Yeah I’m having trouble with a 38mm
@michigantroutaddict4910
3 жыл бұрын
Just drilled mine out and it definitely sounds much better and doesn’t seem to have caused any low end power loss. I did notice I’m getting an occasional lean pop but the bike also popped before I drilled out the silencer. Definitely going to pick up a piggy back ecu soon.
@MotoMirius
3 жыл бұрын
Sounds great. Yes, more pop is normal as the air flows more freely. Not always lean running. Pop is also caused when throttle shut off dumps unburnt fuel into the exhaust
@10sss77
Жыл бұрын
This video is really informative and not many on these bikes at all so thanks a lot, I’ll take the advice of the decat pipe but keeping a baffle 👍
@MotoMirius
Жыл бұрын
Thanks. Typically I run a decat, keeping the presilencer. This allows me to run any slip on I want - from quiet to loud without any risk of it being too loud.
@MelegaPF
Жыл бұрын
Great!!! I bought a Duke yesterday and today on morning remove original db killer as you.
@MotoMirius
Жыл бұрын
Great stuff!
@siddharthsingh2808
4 жыл бұрын
First i thought that my left earphone isn't working 🤣🤣🤣
@MotoMirius
4 жыл бұрын
I'm glad to see that my test to see if you were paying attention worked :D Skäl David
@MotoMirius
4 жыл бұрын
@Mags64 I'm deaf i my right ear - I can hear sound coming from the left - I can't hear if the right headphone is making sound. The right headphone plays sound captured by the right mic channel and in this case no sound was recorded in the right mic channel - no inversion, that is sorted in the mic.
@MotoMirius
4 жыл бұрын
@Mags64 Ha, no problem, it's just annoying that it happened and I didn't catch it before it was published and it got locked down.
@chazphot
4 жыл бұрын
Never seen someone use a hole saw for getting out a welded baffle before but it seems like a great solution. I was waiting for you to get that swarf out with a handful of throttle :)
@MotoMirius
4 жыл бұрын
Ah, I just can't tell you how tempted I was to do exactly that, but I could just see all the negative comments :D Skäl David
@RogueSamd
4 жыл бұрын
I'm going to do that on my husqvarna 701 vitpilen someday when I have one.
@MotoMirius
4 жыл бұрын
That's a nice bike. Skäl David
@RogueSamd
4 жыл бұрын
@@MotoMirius i love it
@MotoMirius
4 жыл бұрын
Thanks
@shobharani2698
3 жыл бұрын
I'm stiil gonna buy the Akrapovic just because it looks sooo good on the duke 390
@MotoMirius
3 жыл бұрын
Nothing wrong with buying parts because they look good!
@garethmayfield4014
3 жыл бұрын
I've just tried this with my 1290GT. 51mm hole saw. what a nightmare!!!! saw would not touch it. ended up chain drilling with a 2mm coldest drill. sounds fab though.
@MotoMirius
3 жыл бұрын
Glad you got there in the end. Stock exhaust is quite high quality - not sure about the 1290 but I'm assuming that it's also stainless which is really tough to cut and you need a decent quality metal hole saw which is also long enough. But what counts is making it work, so fantastic! Skäl David
@mattbowman3641
3 жыл бұрын
Jeeeeeesus!!!!40mm lol I've just realized I've been using a 38mm and I've effed it lol why didn't i check out your vid sooner?!lol..thanks mate
@MotoMirius
3 жыл бұрын
Smaller works, just harder to cut through! Good luck! Skäl David
@mattbowman3641
3 жыл бұрын
It really didn't i bought a brand new saw bit,lubed it with cutting oil..it seem to just chatter around because of the loose fit..anyway it stripped the teeth lol.after i seen your vid i went back and gotta 40mm and bingo haha it sounds waaaaaay better man!!
@MotoMirius
3 жыл бұрын
@@mattbowman3641 Yeah, the reason for going bigger is because you avoid the weld in the centre. It's stainless steel so very hard and will blunt the teeth - it's why I recommend as large as you can fit in there. Some people have managed it with 38mm but.... Glad you managed it! Great job!
@mattbowman3641
3 жыл бұрын
@@MotoMirius cheers mate,same here!!I'm lovin' your 390 vids man.lol keep em coming!!🤘🤘i think my next step is a new bars setup and power commander 5 with k&n.
@MotoMirius
3 жыл бұрын
@@mattbowman3641 Thanks and sounds like a plan. Good to see that Dynojet have finally stepped up and now offer units for the gen 2 Dukes.
@noobonline4674
4 жыл бұрын
Really awesome video, m going to do with my RC390, Thankyou
@MotoMirius
4 жыл бұрын
Thanks. Good luck with that. Skäl David
@jorgenlannock
4 жыл бұрын
Very east and perfect result. Thanks 👍👍✌️✌️
@MotoMirius
4 жыл бұрын
Welcome and thanks 👍Skäl David
@TheCoooool123
4 жыл бұрын
Volume normalization and that's the first time I've heard someone call it a-crap-o-vich 😂👌
@MotoMirius
4 жыл бұрын
Volume is now beyond my ability to correct, but at least you now know how the manufacturer pronounces it!
@rjtastic
4 жыл бұрын
bro when you record the audio just use the "mono" setting or just use mono settings in your editing program! you'll never get unwanted results that way. informative video tho.
@MotoMirius
4 жыл бұрын
Thanks. This is the only video I’ve had this problem with. If I weren’t deaf in my right ear I would have caught it in post. Skäl. David
@rjtastic
4 жыл бұрын
@@MotoMirius oh my god I'm really sorry on behalf of all these hate internet trolls.
@MotoMirius
4 жыл бұрын
RP ha, no problem. It’s just very irritating that I didn’t realise until it was uploaded and live. Just one of those things! Skäl
@janmajnik6889
4 жыл бұрын
@@MotoMirius consider a cheap lav mic. Would improve your sound in the videos a lot! I really enjoy your content!
@LVCMTB
4 жыл бұрын
Nice vid. Thanks
@MotoMirius
4 жыл бұрын
Thanks, much appreciated Skäl David
@springy-2112
5 жыл бұрын
I don't think my bm has an exhaust , at least I can't hear it 😀but the new bike makes up for it its got 3 👍🏻peace and love brother 👍🏻☮❤
@MotoMirius
5 жыл бұрын
Cheers Springy. What’s the expected life span of the new bike? 🤘. Skäl. David
@springy-2112
5 жыл бұрын
@@MotoMirius Well, at least 3 months if it's going to be a long term one 😭 after all I've only had 51 bikes now all different and there's still hundreds to get through 👍🏻😁🤘🏻
@shivdeepsinghgrewal3920
4 жыл бұрын
You got good stuff mate.
@MotoMirius
4 жыл бұрын
Thanks, appreciated. Skäl David
@abhishekbose317
5 жыл бұрын
Nice video mate...awesome.. 👍🏻
@MotoMirius
5 жыл бұрын
Thanks. Much appreciated. Skäl. David
@enairb.3986
4 жыл бұрын
we also do that in Philippines after enlarging the hole we put fiber to make deeper sound we call that "kalkal"
@MotoMirius
4 жыл бұрын
Sounds interesting 🤔 Skäl. David
@enairb.3986
4 жыл бұрын
my comment got a heart❤
@MotoMirius
4 жыл бұрын
Nocturnal PlayZ of course. Great content 👍
@enairb.3986
4 жыл бұрын
oh thank you!!
@tonyvargasjimenez6021
5 жыл бұрын
I want to see that new video to cut the exhaust 👌✊🤩
@MotoMirius
5 жыл бұрын
Coming soon Tony. Makes a much better braap than the stock exhaust even without the baffle. Skäl. David
@MrDingle1987
5 жыл бұрын
Me too tony. I am waiting to buy another stock exhaust. Won't buy it until I have seen the stub cut. Can't wait much longer lol
@jespertordebringjansson1397
4 жыл бұрын
how to fix the sound in sound blaster xfi5 software: turn sorround on to 100%, turn smart volume on normal to 60% and balanse the audio to +5 on the right ear in the realtek audio software, and boom you got the sound on nearly both ears!
@MotoMirius
4 жыл бұрын
Good to see some lateral thinking at play. Skäl David
@sandeepkochgood7111
3 жыл бұрын
Perfect sound!
@MotoMirius
3 жыл бұрын
It’s a good sound 👍
@MrAmorti
4 жыл бұрын
Magnet on a stick would be a good tool to retrieve the baffle and clean up the cutting swarf
@MotoMirius
4 жыл бұрын
It's stainless steel - magnets don't work very well. But you can certainly use a stick and maybe some tape to achieve the same. Skäl David
@SaddamHussain-sp7ow
4 жыл бұрын
Owsm trick sir 👍
@MotoMirius
4 жыл бұрын
Thanks and welcome
@mktmtu1291
4 жыл бұрын
Great video
@MotoMirius
4 жыл бұрын
Thanks. Much appreciated. Skäl. David
@JO-nx4se
4 жыл бұрын
I thought my right earphone 💥 🤣
@bonvincentagbisit4503
4 жыл бұрын
Nice vid. Keep on makin em.👍
@MotoMirius
4 жыл бұрын
Thanks. Much appreciated. 👍 Skäl. David
@OscarDiaz-gr6ib
4 жыл бұрын
El sonido es mas ronco 👍q belleza...
@MotoMirius
4 жыл бұрын
El sonido es bueno Skäl David
@mrstroph9042
4 жыл бұрын
Would be lovely, if anything of that would be legal in germany :X
@MotoMirius
4 жыл бұрын
Yeah. Germany isn’t a great place to live if you want to modify your vehicle. Skäl. David
@Fekillix
4 жыл бұрын
Every non motorcyclist appriciates that law.
@mrstroph9042
4 жыл бұрын
@@Fekillix i dont think so, even Back Then, where i havent been a motorcyclist, i still loved the Sound engines make, as a kid..
@memxak2338
4 жыл бұрын
N e ii o X Yea until it blewd your ears away
@elia3954
4 жыл бұрын
@@MotoMirius If Germany is not a great place to modify the vehicles, What should I say that I live in Italy? 😂 Nothing can be done here
@kiwiboy82
4 жыл бұрын
sounds good
@MotoMirius
4 жыл бұрын
Thanks. Skäl David
@rogerpriestwell6379
4 жыл бұрын
...and it's not a race??? Oh but it is,... it's a KTM !!!
@MotoMirius
4 жыл бұрын
Well, that is a fair point! Skäl David
@bhishamchandiramani2230
4 жыл бұрын
Does removing the baffle on a new 390 , harm the engine in any way?
@MotoMirius
4 жыл бұрын
It’s unlikely. Akrapovic slip on is more free flowing than the stock exhaust and KTM advise that no changes are necessary when fitting that. Skäl. David
@kenssnog2768
4 жыл бұрын
@@MotoMirius I guess they have calculated the back pressure before hand and tested on dukes and made changes accordingly to the akrapovic i think. But do you know if it harms in any way if i remove the db killer as you know the fuss about back pressure maintained on stock exhaust?
@MotoMirius
4 жыл бұрын
Back pressure is important. But I suspect that you are overlooking the fact that this is the tertiary unit. Back pressure is primarily provided by cat and presilencer. If like me you have decatted the bike then it runs better with a baffle. Skäl. David
@kenssnog2768
4 жыл бұрын
@@MotoMirius Well I didn't know that the back pressure are maintained on cat and pre silencer but I guess even if has slight changes the oem ecu map could adjust for small changes, right?
@MotoMirius
4 жыл бұрын
@@kenssnog2768 Backpressure has very little to do with the ECU map - back pressure has a different impact on the fuelling. Baffle removal increases air flow which alters mixture which does impact on the ECU map - and the ECU does have some ability to compensate for this.
@TheJWC56RSA
5 жыл бұрын
Very informative as always. Thanks David. Why would you keep the baffle when you decat? Regards.
@MotoMirius
5 жыл бұрын
Because the decat makes the bike a lot louder. It depends where you live but I have to keep the baffle in on my Akra because otherwise it would be a police magnet 😂😂. Skäl. David
@jakedeadmon1183
3 жыл бұрын
I have the full cat and premuffler delete with the db killer installed and it's too loud now. Take out the baffle and it would sound like a straight pipe.
@mr.mystery-X
3 жыл бұрын
So did i get more tor. Or hp. If i do the same at my duke 390 or not?
@MotoMirius
3 жыл бұрын
Not that you will notice. Getting extra power normally requires adding little bits from several different changes. Some people have claimed a loss of power, but there is no one single simple answer (despite what some sellers might want you to believe).
@KROWARIZONA
5 жыл бұрын
Nice video! I can’t wait to see the next one. Well, I have a question about the DeCat. When you do the DeCat do you have to add some device (like a micro computer, chip) to indicate the system of the bike that you are not using it?
@MotoMirius
5 жыл бұрын
Thanks. Yes, you do. I talk about it in the decat video. Though with decat most people including me mean cat and presilencer. ECU is locked which means you need an external device between bike and ECU. Skäl. David
@sairamlalibai4539
2 жыл бұрын
Nice 👍 video you should use magnet 🧲 to pull the db killer to much better to hadel the way
@MotoMirius
2 жыл бұрын
Thanks. Stainless steel isn't magnetic. It's easier just to tip it out as you should remove the metal cuttings anyway.
@cbzhoney
4 жыл бұрын
Sir what will happen if we cut the waffle in half and again weld it in?
@MotoMirius
4 жыл бұрын
It will be a bit louder. See my other videos on this exhaust. For example Removable Baffle DB Killer Stock Exhaust KTM Duke 390 125 250 kzitem.info/news/bejne/yHx8vHWhi6hyonY. Skäl. David
@angweirdo7604
4 жыл бұрын
Awesome 👏
@MotoMirius
4 жыл бұрын
Thanks, much appreciated. Skäl David
@meatboy5246
4 жыл бұрын
I have a 2019 rc 390, I bought an akra and was disappointed when I found you cant just remove this when you like, it sounds pretty similar to stock sound. Would this be the best method or what other options are they. I wouldn't like to mess up a 500 pound plus exhaust. Great vid by the way. Also is this legal and fine for MOT etc.
@MotoMirius
4 жыл бұрын
Thanks Richard. The Akra baffle is removable and you can fit an aftermarket baffle that is louder than the Akra one. Akrapovic Exhaust DB Killer Removal KTM Duke 390 125 250 kzitem.info/news/bejne/rYSNyaqigIGVpqw I will be making a video on making the baffle easily removable using the same system Akra used before Euro4 banned removable baffles once I’ve summoned up the courage to drill the carbon fibre. The biggest change to sound levels will always be decat. Skäl. David
@duken8115
4 жыл бұрын
what is the sound? Can you make a video and show the sound?
@MotoMirius
4 жыл бұрын
Check out my other exhaust videos for the sound. Skäl David
@joshuabell473
Жыл бұрын
Great video. I want to know. Will this affect the decompression of the engine
@MotoMirius
Жыл бұрын
Thanks. KTM state that fitting the Powerparts Akrapovic slip on requires no changes to the engine - this does not have a bigger effect than fitting the Akrapovic
@רוןממן
3 жыл бұрын
hai. i enjoy watching this channel... I wanted to ask if this video in particular can be applied to duke 690...and if is there a way to get rid of the ugly presilencer.
@MotoMirius
3 жыл бұрын
Thanks, much appreciated. I'm not familiar with the 690 stock system and not sure how it changed over the years so I can't comment on this particular mod. But there are certainly cat delete pipes out there so I suspect some of those will also delete the presilencer.
@gekolizzard
2 жыл бұрын
So…I removed the db killer…sounds far far better than it did. A louder bike is a more noticeable bike and where I live that’s a good thing. Motorists just don’t see bikers…well now they’ll hear me.😁
@MotoMirius
2 жыл бұрын
I rely on noise to wake up drivers every time I ride. I can get a big bike through traffic just as quick as a small bike purely because drivers move out of the way as they hear it coming.
@melallanaseron5552
4 жыл бұрын
Hello from the Philippines... Do I have to replace my ecu for piggy back type if I will do like this exhaust?
@MotoMirius
4 жыл бұрын
Hello. Most people consider that unnecessary for this mod. KTM advice is that no change is necessary when fitting the more free flowing Akrapovič exhaust so I see little difference here. Skäl. David
@TheJWC56RSA
4 жыл бұрын
I bought the same cutter and tried it on my 390... after about 5 min of cutting I can barely see a cutting mark inside the exhaust.... I tried some expensive 4mm high end carbon drills to perforate the pipe (suitable for stainless steel) and even those struggle to drill through! (I used slow speed and enough oil). The exhaust seems to be very hard steel...
@MotoMirius
4 жыл бұрын
I’ve heard of people having trouble. Are you sure that the chuck isn’t fouling on the baffle? If the teeth can’t reach they can’t cut. It’s only 1mm steel but it is stainless so it will tough so it needs a hole saw for metal. Skäl. David
@TheJWC56RSA
4 жыл бұрын
@@MotoMirius The part I drilled through looks like 2mm or more stainless... the cutter is made for stainless and not touching - it is a 38mm cutter - I can only guess I'm going through the weld inside too....
@MotoMirius
4 жыл бұрын
That’s possible and if you are using 38mm you are could be into the thicker part where it curves back into the baffle. I’d still double check you aren’t hitting the tip of the baffle
@antarikshverma1810
3 жыл бұрын
After are moving Db Killer Is the bike Performance Decreases?
@MotoMirius
3 жыл бұрын
Some people say yes, some people say no. Unfortunately bike tuning is not so simple and depends on many other factors.
@akash1281
4 жыл бұрын
Does it harm the engine....iam planning to do the same...suggest me ,should I do it or not....plz make a video on this topic....iam waiting
@MotoMirius
4 жыл бұрын
I have a video planned regarding my thoughts on the subject. I will make it sometime soon. Skäl. David
@akash1281
4 жыл бұрын
Moto Mirius sure,will be waiting for the video....👍
@rajpriyam6640
25 күн бұрын
Is your bike safe? Did you removed the db killer? How's the bike now?
@KROWARIZONA
5 жыл бұрын
Could you give me the specification about this (in 3:14 video) tool please? I’d appreciate. Thank you
@MotoMirius
5 жыл бұрын
It’s a 40mm hole saw for metal. For this job just a cheap one is fine. Skäl. David
@davidgasparatos4531
4 жыл бұрын
I did this on my ktm duke 125, it sounds a lot better but I think it feels a bit slower, does the removal effect the acceleration?
@MotoMirius
4 жыл бұрын
Power tuning is a complex subject. I don’t think this has much impact on acceleration but you’d have do dyno runs before and after to really know. Skäl. David
@ultralinx200
4 жыл бұрын
@@MotoMirius dyno is much expensive than buying new aftermarket exhaust
@MotoMirius
4 жыл бұрын
Yes it is. But without using one you are only guessing what the impact is of any modifications. This is why companies like Akrapovic use a dyno when designing new exhausts. Louder exhausts sound faster but may actually be slower.
@abdallahbidawy2211
3 жыл бұрын
what kind of hole saw is that?? tried a regular metal one...the blades became round and fluffy! haha
@MotoMirius
3 жыл бұрын
You are cutting into stainless so cut slow with lubricant. And yes, use a decent quality saw because stainless is hard. Also make sure its as large as you can fit to avoid the weld because this is thicker.
@lunarsolis8109
4 жыл бұрын
Hello, what’s the size of the bit you used ?
@MotoMirius
4 жыл бұрын
I use a 40mm hole saw
@Marcel204_
4 жыл бұрын
good video :)
@MotoMirius
4 жыл бұрын
Thanks. Much appreciated. Skäl. David
@Bscott-390
11 ай бұрын
Why keep the baffle if you remove the cat? Thanks. great video
@MotoMirius
11 ай бұрын
Thanks - a great question. It's a balance as to how loud you want the bike to sound. Personally I rarely have a baffle in, but some people need or want it to be a bit quieter. There are people who run straight through exhausts - but they must either live somewhere where there are no laws or no police and have no neighbours or they don't just have any regard for anyone except themselves. Everyone else has to choose where they want to be on the balance of what sounds good and what is just annoying for everyone else.
@Bscott-390
11 ай бұрын
If I cut out the resonator and the cat delete, will I have to do fuel management/tune? @@MotoMirius
@MotoMirius
11 ай бұрын
It would be strongly recommended, yes@@Bscott-390
@transdetendal
4 жыл бұрын
eny idea on " fixing" a stainless motad 4in1 ? i hate the restricktion on it !!
@MotoMirius
4 жыл бұрын
Motads tend to be welded so might be difficult. Depends on what it looks like. Skäl. David
@transdetendal
4 жыл бұрын
@@MotoMirius yup its welded and in one with the 4into 1 ... skål and have a good one !
@rebecca1610
4 жыл бұрын
Great video. I did this a couple weeks ago to my 2020 duke 390 and it sound great. I just bought a Powertronics piggyback ECU and am wondering if I need a dyno tune or can I use the map they already have installed? This is the only mod I’ve done but I’m considering the Coober air box lid at some point.
@MotoMirius
4 жыл бұрын
Thanks. Their standard map should be fine. PowerTronic do great modules but you really need to be sure that the map matches your configuration. I would recommend the mapped units like that for more developed builds where you are looking to build power and know what you are doing. Skäl. David
@rebecca1610
4 жыл бұрын
Moto Mirius Which would you recommend I use instead of PowerTronic?
@MotoMirius
4 жыл бұрын
If you have the PT then use it but check that the supplied map works with your configuration. Normally this is OK but mapped units are better for track day and power builds. For street use where you are not monitoring the bike then something like a RapidBike Evo Exclusive is better in my opinion.
@hectorvalero8562
4 жыл бұрын
Does anyone know if this works for the 2019 model?
@MotoMirius
4 жыл бұрын
2019 has the same exhaust. Skäl. David
@tommo6464
4 жыл бұрын
Hi, Great video. Will this work on all stock EXHAUSTS? I have a husqvarna vitpilen 701
@MotoMirius
4 жыл бұрын
It will work on many stock exhausts - but the details vary. It's best to take it apart first if it made up with rivets so you can how its constructed.
@tommo6464
4 жыл бұрын
@@MotoMirius yea I checked... I would need a very long hole saw to get to it annoyingly as it is like a slanted end.....
@John-hi2yi
5 жыл бұрын
Nice video, are going to do an update of the learning CPU you fitted?
@MotoMirius
5 жыл бұрын
Thanks John. Yes, it’s in the works. Just trying to get a broader spread of opinions from people who have them. Skäl. David
@JQUICK21
4 жыл бұрын
Would WD40 be OK to use instead of cutting oil? Hope so! Or how about simple Motor Oil?
@MotoMirius
4 жыл бұрын
WD40 is a water dispersant not an oil. Use motor oil. Skäl. David
@sairamjella3526
4 жыл бұрын
Any milage changes after removing db killer?
@MotoMirius
4 жыл бұрын
I don’t measure mileage. But as I will always say - it’s likely to make it worse because you will rev the engine more to hear it and revving the engine is always bad for mileage.
@albertaragon1132
4 жыл бұрын
Hey man what model is your impact driver? Cheers
@albertaragon1132
4 жыл бұрын
Or its a drill driver?
@taylorcerri4929
4 жыл бұрын
Why didn't you take the muffler off the bike because of all the metal shavings going down it
@MotoMirius
4 жыл бұрын
Because the bike is the best way of holding the muffler without risk of damage. Shavings don’t do any damage and even if you don’t tip them out, most will blow out once the bike is running. Skäl. David.
@barbudomotero3903
4 жыл бұрын
And now. How to put a DB killer to exhaust?? I cant pass inspection witout this
@MotoMirius
4 жыл бұрын
If you have a welder it’s pretty easy. Im not finding a commercially made DB killer small enough to fit. If there was it wouldn’t be too hard. I will be making my own instead because I can’t run the stubby version of this exhaust without one. Skäl. David
@LEBXLS
4 жыл бұрын
Super l'ami!
@MotoMirius
4 жыл бұрын
Skäl. David
@cramadventure1900
4 жыл бұрын
lami gyud kaayo
@dhruvsingh2666
4 жыл бұрын
hi i want to know about the tail change is it custom made cuz i was not able to find it online. nice vid BTW 👌👌
@MotoMirius
4 жыл бұрын
Hi and thanks. If you are asking about the tail tidy, it is a cheap Chinese piece of rusty metal. Whilst it works well, I couldn't recommend it. Skäl David
@forrestdevine2336
2 жыл бұрын
@@MotoMirius I purchased a tail tidy from Mustard Bikes in Australia for my 2017 Duke 390. Excellent build quality, came with all the hardware I needed. Includes an LED plate light and retains the factory turn signals. Can't recommend it enough.
@MotoMirius
2 жыл бұрын
@@forrestdevine2336 sounds great!
@Robocoppat
4 жыл бұрын
David, Do they make a dual exhaust for this bike? And if not, would performance be Affected if I made one? Does that make sense?
@MotoMirius
4 жыл бұрын
There are a couple of dual exhausts for the bike - IXIL for example, though I think most were for the gen 1 (but can be fitted if you use the gen 1 header). Exhausts affect performance to some degree so it would depend how good your understanding of exhaust dynamics is - it's certainly easy to to make performance worse. Skäl David
@Robocoppat
4 жыл бұрын
@@MotoMirius I worked in an automotive exhaust shop years ago so I kind of have a grasp on it. However I wouldn't want to affect any power performance just to have a cool looking pair of dual exhaust. I was just wondering. Thank You for the prompt response. God Bless
@vittoriodantona6378
Жыл бұрын
Once Removed, can you put it back? I live in a city and there’s lot of police
@MotoMirius
Жыл бұрын
I live next to a major airport so police presence is very high with a lot of bored police looking for something to do. I have a separate video on how to make it removable.
@travancorepistons7309
2 жыл бұрын
Hi.. can we change the tank of 2012 ktm duke 200 to 2020 duke tank..
@MotoMirius
2 жыл бұрын
I don't have a gen 1 but don't see any reason why not. You may need to make modifications to brackets and seat will be an issue
@SCutchins
4 жыл бұрын
You said that you may not want to de-baffle if you de-cat. Why is that? I did a full de-cat, straight pipe from header to stock silence, and the exhaust has a bad "ringing" sound at about 5,500 RPM so I'm considering the de-baffle. Thanks Edit - figured I would add that i added a Powertronic so she's getting more fuel.
@MotoMirius
4 жыл бұрын
Removing cat, presilencer and baffle is too loud for most places - it’s either illegal or it’s just a police magnet who will pull you over to check what they can find wrong with the bike or your license. Otherwise there is no technical reason you can’t do it but you should seriously consider a proper piggyback as you will almost certainly be outside of the stock fuel map parameters. Detonation can create a lot of damage in the engine and whilst you can ride for a long time without any issues just a few minutes outside of the map will grenade the engine.
@stevecutchins9069
4 жыл бұрын
@@MotoMirius Thanks for the reply! I do have a piggyback, I edited my comment afterwards to add that I do have a Powertronic, which I highly recommend by the way, massive difference in rideability without that ridiculous stock surging.
@MotoMirius
4 жыл бұрын
PowerTronic do good systems. Just make sure the map suits your setup.
@surslaughter3524
Жыл бұрын
So if I do this and then add a powertronic fuel auto tune device on my stock 22’ 390, I will have a less go cart sound and run less lean while preparing to go full exhaust down the road? I want to go catless but don’t want to void my warranty. So this sounds like the right direction. Except I imagine cutting out the baffle will also void my factory warranty.
@niktopore7734
11 күн бұрын
Will this work on my 2020, 1290 super duke gt? I already removed the cats. Only have the stock slip on
@MotoMirius
11 күн бұрын
I'm told that it does by people who have done it, but I can't speak of every generation of 1290 as to what exhausts are fitted.
@steveolkinevil
3 жыл бұрын
I did this even though a voice was telling me not too, definitely the worst thing I've done on my bike, looked at loads of sound check videos too but it's hellish loud now 😫
@MotoMirius
3 жыл бұрын
I suggest that you don't decat if you think this is loud!
@steveolkinevil
3 жыл бұрын
@@MotoMirius I originally took the full silencer off, omg it was unbelievable, my fj1200 isn't as loud with the pipes off
@MotoMirius
3 жыл бұрын
@@steveolkinevil Did you take off the full silencer or just the slip on? With a straight through it isn't quiet, that's for sure. I normally use a baffle but with some exhaust modifications - you can tune this to different sound levels. And no, sound videos are so inaccurate I don't make them any more.
@alexxpdirt
4 жыл бұрын
Very thanks Graham Jarvis !
@MotoMirius
4 жыл бұрын
You are welcome and appreciated. Skäl David
@kaleemmohammed7215
3 ай бұрын
Does removing the dn killer kills the engine ? Or affects??
@MotoMirius
3 ай бұрын
The Akrapovic slip on that KTM sells is more free flowing than this conversion and KTM are very clear that no changes are needed when fitting the Akrapovic
@scrvlogs4118
5 жыл бұрын
Will it hamper the engine? and should it be done before 3000 km?
@MotoMirius
5 жыл бұрын
I suggest not before first service. So long as you have made no other changes, this is normally fine. Skäl. David
@shahidyousuf5392
3 ай бұрын
"I used heat gas welding to remove the db killer from exhaust of my KTM Duke BS6. I successfully removed it, but the heat caused two big holes in the exhaust net near the end of the exhaust. Will these holes make the sound louder or quieter? Could there be any problems with the exhaust or engine because of these two big holes? Please reply."
@MotoMirius
3 ай бұрын
This is why I do not recommend that method of removing the DB killer. The heat will also have damaged the insulation in the silencer so you can expect it to be louder than it should be. It should not create any issues with the engine so long as you have made no other changes to the bike - air filter, cat delete etc. If you are concerned, get another silencer and try again or use something like the FuelX Lite to make sure the engine runs correctly.
@shahidyousuf5392
3 ай бұрын
Thanks for your reply. I want a louder exhaust. I was worried that it might cause any problems. Now you have reassured me. I appreciate you replying to my comment. You've got a new subscriber. Thanks, buddy!
@rajpriyam6640
25 күн бұрын
Is your bike engine safe?
@anthonycaldi7056
4 жыл бұрын
Great Video...Question....is there any concerns about the metal shards left in the exhaust from drilling?
@MotoMirius
4 жыл бұрын
That is why I removed them. But if you leave them I don’t see an issue. They will remain in place or be ejected without issue. Skäl. David
@anthonycaldi7056
4 жыл бұрын
Thanks for your response. It really does make a huge difference!
@DarioTelloLab
4 жыл бұрын
Hi , does this change improve or worsen the bike's performance? I know that removing the db-killer changes the carburetion
@MotoMirius
4 жыл бұрын
Removing the DB killer will alter the carburetion but for most applications within the existing KTM fuel map. It is impossible to guess exactly what the effect will be for your bike. There are many variables which affect carburation and performance including fuel and altitude which would change the actual impact on your bike compared to mine, however if you are running a stock exhaust then I think you are overthinking this. Skäl David
@ravikiran3320
22 күн бұрын
Which drill machine i need to buy and also please tell me what is that attachment of 40mm?
@MotoMirius
21 күн бұрын
Whatever you have - you could do it by hand but it would be hard work. It must be a good quality metal hole saw - nothing else is going to cut through stainless steel easily.
@acousticwarrior7
3 жыл бұрын
Great video, very informative. I have a Honda shadow 125 that I want to de baffle, 2 questions do you know if it is perfectly legal in uk? And would it cause any problems with future MOT? Thanks
@MotoMirius
3 жыл бұрын
Thanks. MOT doesn't (yet) fail on louder exhausts - but I have heard of some testers who do. The solution is to take it to a different testing station who will give you an advisory instead. There are normally testing stations who are more in tune with cosmetic alterations for bikes. Of course running L Plates never helps (if you do). As for legality, if you get pulled by DVSA then it's an issue (but this is very rare and typically only happens at regular big bike meets in public places), the police less so - but again it gets attention and that can cause it's own issues because 125 riders are assumed to be less experienced and more likely to have poorly maintained bikes - so loud exhaust is a good excuse to be pulled over. This is especially true for the really badly debaffled 125s which are very loud - but in a very bad way, just like a car where the exhaust has fallen off loud instead of supercar loud - same volume of sound but one you don't want to hear and the other you want to hear - it's all in the tone and tuning of the sound (so you need to keep some silencing). Bad loud = pulled over by police, good loud and a bike that looks well maintained = not pulled over by police
@acousticwarrior7
3 жыл бұрын
@@MotoMirius thank you very much for that very helpful, personally I don't want to go silly loud I just want a bit more beef lol I'm still in 2 minds about doing this, i have the silver tail exhaust, are there any other options I could look at? Thanks again
@MotoMirius
3 жыл бұрын
@@acousticwarrior7 Just a debaffle is not normally silly loud. I can't really say what options you have for the Honda, but if you have the silvertail, and the baffles are removable then you go custom and try different baffles. I use Pipewerx for this - to just buy baffles to size. I actually need to do this on my XVS because the current baffles are just a little too loud for my liking - I should have added in the first place that cruisers rarely have issues with getting stopped for being loud - it's sort of expected.
@acousticwarrior7
3 жыл бұрын
@@MotoMirius oh wow ok I never realized that you could actually get different baffles I thought it was literally there or not. And yes I guess you're right it is expected with a cruiser. I don't suppose you have a video showing the difference in baffles? And can any exhaust take any baffle?
@MotoMirius
3 жыл бұрын
@@acousticwarrior7 For an example of two baffles kzitem.info/news/bejne/rYSNyaqigIGVpqw Baffles are sized by the diameter of pipe they fit into. www.pipewerx.co.uk/webshop/accessories/db-killers-baffles/custom-baffles/ Not every exhaust is designed to have the baffles removed and emissions regulations are making it harder - which is what the video above is all about.
@mktmtu1291
4 жыл бұрын
But does this affect the engine back pressure in long term run ???
@MotoMirius
4 жыл бұрын
Most of the back pressure is created by the cat and presilencer. KTM wouldn’t be the exclusive sellers of the Akrapovic slip on which is more free flowing than the stock can if they believed there was any risk. But it’s your bike so you must make your own choice. Skäl. David
@mktmtu1291
4 жыл бұрын
@@MotoMirius Thanks a lot brother... So im planning to remove the baffle .... Which is better than a costly exaust replacement ....
@Calvingarage
2 жыл бұрын
Hello, old post but I have a question for you, I have a duke 390, 0km 2021 bs6, still in brake in. The vibration on the entire bike is insane, all the frame,, handle, foots, everything vibrates so much. Do you think un your opinion it may be an exhaust resonance or something? Or maybe something more serious. I like to do these things by myself.
@MotoMirius
2 жыл бұрын
Hard to say without seeing the bike - compared to my Sportster the Duke is silky smooth. All singles will have some vibration and more race oriented ones like this have more. But I don't notice anything particular - but then I'm used to the Sportster. It doesn't seem likely the exhaust would vibrate the whole bike.
@VFactory-vl5fi
4 жыл бұрын
Hi mate, if the dB killer is removed from the stock exhaust? Will this fail the mot?
@MotoMirius
4 жыл бұрын
Unlikely. Depends on the tester. Depends if you are running L plates or the bike doesn’t look well cared for. You might get an advisory - some consider that a badge of honour. The bike only gets loud when you decat it. Skäl. David
@connorpitts639
Жыл бұрын
My bike has no catylic converter. Will it be harmful in any way to the bike if I remove the DB killer as well? Thinking of doing this so I’d like your feedback. Thanks.
@MotoMirius
Жыл бұрын
As a rule of thumb I recommend only one change if you want your bike to be safe. But it is easy to fit something like a FuelX Lite to keep your engine safe - engine rebuilds are very expensive.
@zeez9053
3 жыл бұрын
Yes that’s how u do it but what about fuel consumption/is it better for bike for the engine to breathe /is it better for horse power etc ? Loads of questions not being answered
@MotoMirius
3 жыл бұрын
This is a video on how to do it - the other questions are subjective and largely dependant on what you are doing and many of them will depend on where you live and how you ride. Each of them needs it's own set of videos to make any sense - I have started a series of short videos to discuss the basics behind your questions because the answers are not as clear as I suspect you think they are - it is not a case of do this, do that and then this happens - no matter what some videos might want you to believe. A quick example - this will increase your fuel consumption - not because it makes the engine less efficient but because you will rev the bike more once you can hear it and this burns fuel.
@zeez9053
3 жыл бұрын
Moto Mirius Thank for your explaination and your time
@roxd3906
2 жыл бұрын
Removing db killer will cause any harm to engine or power drop in future??
@MotoMirius
2 жыл бұрын
Not if its the only thing you've done.
@Superdisco199
3 жыл бұрын
So what's better - de-beffle or de-cat ? you would lose torque and backpressure with de-baffle ? is the inside end of the baffle tube open ? thanks heaps
@MotoMirius
3 жыл бұрын
Define better? The bike has three silencers - cat, presilencer and tail silencer. Most of the sound reduction is in the cat and presilencer. Removing the baffle makes the bike a little louder. Removing the cat and presilencer makes the bike a lot louder. Most of the back pressure is created by the cat - back pressure from the baffle has to go back through the cat to get back to the engine. Tuning is a complex subject and will be affected by where you ride - altitude, temperature, humidity etc. Some people report loss of torque from removing the baffle others don't - but since no one has put the bike on the dyno before and after the change, these reports (and mine) are speculative. Baffle and cat are the only parts of the system that reduce sound by constriction. Most people make these changes to improve the sound of the bike, not to make it faster. Skäl David
@Superdisco199
3 жыл бұрын
@@MotoMirius Thanks for that... in my experience I've found bikes generally lose some torque when gutted for a better note. Whether its a crf250x or an MT07, you just notice it doesn't loft a front wheel as easy. So I guess in terms of better I just mean nice solid stock like performance but with a little more depth to the note. I can tell just from the KZitem videos that it certainly seems less constricted when revved without the cat(mini cat delete).. but not sure how far will be too far with the bike. Worried that the modified muffler will put me in ag bike land with a boggy feel and was hoping to avoid complete new slipon. (I feel like the pre muffler def. needs to stay)Appreciate your comments.
@MotoMirius
3 жыл бұрын
@@Superdisco199 This was an area I was attempting to address in one of my recent videos but going back into lockdown means I can't get back on to it. My experience is that the baffle removal on a stock system is no louder than the legislation compliant Akrapovic slip on that KTM supplies - my feel is that sound is similar once you debaffle and stubby the stock silencer. As I run a piggyback ECU, I would need to buy a bypass unit for that before I could realistically say what it does to torque. I've been told by someone who has used a dyno that best power comes from cat removal, leaving the presilencer in place and using the Akrapovic slip on.
@Superdisco199
3 жыл бұрын
@@MotoMirius Thanks for that. I just watched your ECU vid. Nice work. I just got the bike and took the whole secondary/final muffler off and it actually seemed to boost the power (wheelied in 2nd). But it had a pretty nasty backfire. Your first stage baffle removal didn't backfire did it ? sounds a bit like I might need to get the RapidBike Easy at the very least.. Bike seems pretty jerky (2020) down low and then flat spots and then comes good. Really suspecting that mini cat removal and single debaffle would be the best trade off, but it's really thejerkyness bothering me most of all. My 250F is carbed and reklused! :-D
@MotoMirius
3 жыл бұрын
No backfire but I always run a piggyback. Backfire is typically a sign of running lean but it can be normal if it’s just on the overrun when there is excess fuel dumping into a hot exhaust with no baffles to absorb it.
@ultralinx200
4 жыл бұрын
I had Gsx R 150, gsx r 125 people called it in euro. Can i doing it on my stock exhaust? It LOOK i can do it, because the tip looks like your exhaust, but i have no idea about how it look like inside
@MotoMirius
4 жыл бұрын
I haven’t done it. It looks like you can and if you have a welder then you could try it and weld it back up if it doesn’t work. Hard to know until you do it as you can’t see the construction inside.
@alconk7129
4 жыл бұрын
Does your Akropovic have a baffle in our out?
@MotoMirius
4 жыл бұрын
In. It was out until I did the decat. Then I needed to put it in to avoid being pulled over by every passing police car. Skäl. David
@mentoocreations8789
4 ай бұрын
I tried but the wholesaw blade has been bended so no cut
@MotoMirius
4 ай бұрын
You need a proper metal saw blade. There is no point trying to cut stainless steel with a cheap blade intended for cutting wood.
@silvertaxi
4 жыл бұрын
Nice vid. Thanks. I’m in Uk. Is it legal, cos of the noise I mean?
@MotoMirius
4 жыл бұрын
This doesn’t make it loud enough to be an issue in the UK. That doesn’t happen until you de cat it as well. Skäl. David
@silvertaxi
4 жыл бұрын
Moto Mirius thank you. Keep up the vids
@Partnerthedog
11 ай бұрын
This doesnt work on the 390 adventure its got a curved exit pipe so you have to open it up
@RajeshThakur-mu2uf
Ай бұрын
Sir what is the size of hole saw.Please reply.😢😢😢
@MotoMirius
Ай бұрын
The size mentioned in the video description. Make sure that it is a good quality metal saw - a saw designed for wood will not cut.
@samueljung2165
4 жыл бұрын
Hey a question = Will my cb650r have the same baffle system? Checking before sawing in
@MotoMirius
4 жыл бұрын
You should be able to check by looking at the back end of the silencer. Skäl. David
@samueljung2165
4 жыл бұрын
@@MotoMirius look into it with a flash or something? Thank you for fast reply!
@samueljung2165
4 жыл бұрын
@@MotoMirius I don't like the look of aftermarket exhausts but you gave me hope
@samueljung2165
4 жыл бұрын
@@MotoMirius I need help. . . ㅜㅜ
@MotoMirius
4 жыл бұрын
You will need to determine how the exhaust is constructed and how the baffle is held in. Many OEM exhausts can be modified but sometimes it is too hard. I don’t have a CBR650R so I can’t comment.
@rajpriyam6640
25 күн бұрын
Does it effect the engine?
@MotoMirius
24 күн бұрын
This is covered in the video. Yes, it will effect the engine - but small changes are within the capability of the ECU to adjust.
@jesusnieves2170
2 жыл бұрын
i dont want to piss off the neighbors
@MotoMirius
2 жыл бұрын
It's why I don't typically run loud bikes. This doesn't make it loud like I think you think it makes it loud.
@dogfish180
2 жыл бұрын
Does removing the baffle help with cornering? Then you can remove those chicken strips off your tyres! LOL! 🤣
@MotoMirius
2 жыл бұрын
It's a brand new tyre, if you look more closely. Try the front page of my website to see an average, not trying cornering picture. Maybe you need new glasses ;)
@samuelwright2219
4 жыл бұрын
I have tried this with the exact same hole saw but it's not going through 🤷♂️any tips
@MotoMirius
4 жыл бұрын
How easy and how long to cut depends on the thickness of the weld. If the centre of your hole saw has hit the baffle you will need a longer hole saw.
@asanuldilbar421
5 жыл бұрын
Do removing baffle leads to any engine issues?
@MotoMirius
5 жыл бұрын
If it’s the only change that you’ve made then normally no. Skäl. David
Пікірлер: 732