Thanks for creating this video! I recently pulled the motor and clutch out of my ezgo and rebuilt it! I pinched a prong and had to pull it again.. your technique worked flawlessly both times!
@SF-hd5ds
5 жыл бұрын
Worked like a charm. Thank you! FYI- bolt thread is fine. 3/4" x 2" - 16 thread.
@sparx-86
3 жыл бұрын
Holy shit 😆. Thank you !!! Putting a predator 420 in my golfcart and I needed this video!
@jasonwiggin6204
2 жыл бұрын
Use water the clean up is a lot easier!
@harveynailbanger
Жыл бұрын
Old mechanics trick also you can use white bread. Smoosh the bread white into the hole , its less messy. Thats how i change pilot bushings when doing clutchss on cars...
@shanebellimpracticaldesign
Жыл бұрын
I normally would but on this there is a threaded hole in the crank that I don't want to pack bread into.
@michaelbennett8395
Жыл бұрын
Find thread or coarse thread
@shanebellimpracticaldesign
Жыл бұрын
fine. 3/4" x 2" -
@jimjanssen5426
9 ай бұрын
Clutch tool is only 20.00
@davidharrigill2841
2 жыл бұрын
Didn't work for me.
@bevobus
5 жыл бұрын
I was struggling to get mine off to send the engine to get rebuilt. I had purchased the removal tool, as the bolt was hard to find, and it still wouldn't come off. I finally put some oil in there and put Teflon tape around the threads. It just popped right off with no effort. Thanks a lot!!!!
@cmorinville
5 жыл бұрын
Thanks for creating this video. I had to pull the clutch while mounted to the machine. I used grease and that worked. I had to run the bolt in, pull it out, add some more grease and then tighten it. I had a strap wrench for an oil filter to hold the clutch. It didn't come easy, but I got it as tight as I could get and then tapped it with a rubber mallet to get it to pop off the taper.
@AaronRiegel
5 жыл бұрын
Perfect thank you for sharing and taking the time!🤟
@jhitt79
6 жыл бұрын
That's pretty smart.
@user-fh5fg4qx3n
5 жыл бұрын
i couldnt find a fine thread 3/4 bolt so i bought a 3/4 shank hitch ball, its fine thread and had flat spots at base of the ball for a big crescent wrench. threads were 2” long so no problem there. still cheaper than the special tool bolt
@shanebellimpracticaldesign
5 жыл бұрын
lol facepalm for me. never even thought about that i got like 3 laying around. good to know. thanks.
@my83roadster4me
5 жыл бұрын
What is the bolt pushing against to force the clutch off?
@shanebellimpracticaldesign
5 жыл бұрын
the bolt pushes on the oil creating hydraulic pressure to pop the clutch off
@bige1022
6 жыл бұрын
What is the threading on the 3/4 inch bolt?
@shanebellimpracticaldesign
6 жыл бұрын
I do not know the tpi but it was a fine thread that is all i remember.
@bige1022
6 жыл бұрын
Doing an engine swap at work and this has been the worst part. Either finding the right bolt or buying the tool for $40-$50. Thanks for the info.
@dennychilders8463
4 жыл бұрын
Bread works also
@shanebellimpracticaldesign
4 жыл бұрын
Had not thought about that one but I have used bread to remove bearings
Пікірлер: 23