Thanks, Brad. Yep, working down here in So Cal is rarely a rusty mess.
@davidjones2457
7 жыл бұрын
an I love watching a master mechanic at work. He makes it look so easy.
@defekticon
7 жыл бұрын
Have a Northern truck, have done a 4.30 swap on the front and rear axles. Can confirm I have NEVER been able to pull a hub like that. Even the Axle extensions on my F-350 won't come off like that. Also noticed that there was no outer axle seals on the 2014 F-250 4WD Dana axle. It has a plastic cover. Even the inner seals are different than what was in TSO.
@WaIIyMaven
4 жыл бұрын
Experienced movements showing skill and confidence. This is poetic.
@screamindemon811
7 жыл бұрын
and the shitty thing is there isnt any way to do that change but to go thru all that work to get to them. Always amazes me how one part can lead to an expensive repair bill in order for the fix to be done right. Totally agree to replace both seals while your in there, may as well rather then having to go back in and do it later for other.
@TheyCallMeCoolRon
5 жыл бұрын
Excellent video! I purchased the maintenance manual (cd) and it states you use all these fancy tools. Apparently, all I need is a ball peen hammer, lol! Then again, I live up north.
@timothyholt2934
5 жыл бұрын
TheyCallMeCoolRon 😂
@heribertomejia9136
4 жыл бұрын
Thank for the video brother God bles you
@Graveltrucking
7 жыл бұрын
Never seen a unit bearing come off so easily, 20 pound sledge is needed around here and we are not even an area where road salt is used. Unit bearings are not cheap the set I bought for my 05 350 were 600 each Canadian that was after market, from Ford I was looking at 800 each. My truck had 180,000kms (112,000 miles) the factory bearings were pooched, truck has stock tire size.
@unknown1129
7 жыл бұрын
i bought the special tool to fit in between the 4 hub studs and the housing using the steering to brake it loose
@hls30000
5 жыл бұрын
You didn't show removing the seals
@geraldhenrickson7472
6 жыл бұрын
Yikes this is a great video for us shady tree socket busters. Thanks SO much!
@cesarsanchez5880
8 ай бұрын
Muchas gracias.felicidades
@2491kridge
5 жыл бұрын
I currently have one of these torn apart I’ve gotta put back together tomorrow and that axle was super tight getting it out of the knuckle, I see there’s a special tool you can use to beat the axle back in so it goes far enough into the knuckle and diff, do you use anything like that or are they usually not an issue going back in?
@flmmaz
5 жыл бұрын
You really need the tool you are talking about. It seats the seal on the axle stub at the correct depth in the knuckle and prevents it from getting damaged. I wish I could have filmed reassembly.
@2491kridge
5 жыл бұрын
flmmaz well dang that’s sort of unfortunate I had called a few parts stores on the way home and no one had one readily available, if you just put the axle in and tab the end with a soft face dead blow it should bottom out anyway should it not or is it possible to go too far in with it
@danbob1650
3 жыл бұрын
2hours for bearing from Yankee. Power steering trick. But had all my leaking out so no go
@ronkey4796
3 жыл бұрын
Good job and thanks for not playing loud background music. thanks
@seanmcguffin3387
Жыл бұрын
Were you able to reinstall the axle shafts without replacing the big vaccuum seals?
@flmmaz
Жыл бұрын
You can reuse them if they dont come apart or get damage in the removal process. I always replace them though.
@Kevinvasquez540
6 жыл бұрын
Hello I’m working on a 2014 f250 and wheel bearing is not going in far enough to install snap ring any suggestions?
@lopezdavid888
2 жыл бұрын
Cuanto se cobra $ por este trabajo en dólares?
@yanezdh5673
5 ай бұрын
Excelente 👌
@defekticon
7 жыл бұрын
Got a question about alignment, I've had a 2011 and a 2014 Superduty, both have had a hard pull to the left. Toe and camber are always in spec, but Caster is off. Normal chain alignment shops won't touch the caster on these trucks. Is this something that I can get fixed at a ford dealer? My understanding is that there are caster sleeves in the hubs where the ball joint sits that need to be replaced/adjusted.
@flmmaz
7 жыл бұрын
Most Ford dealers can handle that job with ease, you are correct on the adjustment sleeves. They sit under the upper ball joint retaining nut and can be replaced with many different options to get you into spec.
@youtubeaccount550
Жыл бұрын
7:40 nice save
@AntonioClaudioMichael
6 жыл бұрын
Lol at like to see you do that up north love it
@dirtypocketsct
4 жыл бұрын
Yeah funny to him
@haleyy68
7 жыл бұрын
Nice catch!
@homecyber32283
5 жыл бұрын
@flmmaz you hav a video puttin it all back together??
@joelmolina6300
2 жыл бұрын
Nice job
@mikemike827
2 жыл бұрын
This whole video just to show the seals and not show him taking them out and putting new ones in what the hell?
@perrikdesrocers4507
2 жыл бұрын
Men id would do the other seal but forget the diff parts
@jd_portland
7 жыл бұрын
What kind of snap ring pliers do you use in video?
@flmmaz
7 жыл бұрын
These particular pliers are Mac Tools TPQ-56www.mactools.com/en-us/Pliers/Snap-Ring-Pliers/ea577758-ceeb-476a-a4ab-a4ab014160b8/Quarter-Turn-Convertible-Snap-Ring-Pliers/TPQ56/Straight-Quarter-Turn-Retaining-Ring-Pliers-9-1-2
@149taylo
7 жыл бұрын
You an instructor for ford?
@flmmaz
7 жыл бұрын
I work part time at a local community college.
@fullmetaltoolbox1412
7 жыл бұрын
flmmaz I would have probably taken the first grade too lol
@TheFroztyloco
6 жыл бұрын
@@fullmetaltoolbox1412 Hi my front differential on my 2006 f250 has play at the knuckles both sides should i replace the hubs, all 4 axles, and seals?
@fullmetaltoolbox1412
6 жыл бұрын
Jorge Amelco @flmmaz is who you are looking for. Good luck!!
@TheFroztyloco
6 жыл бұрын
@@flmmaz Hi my front differential on my 2006 f250 has play at the knuckles both sides should i replace the hubs, all 4 axles, and seals?
@davidshowalter2537
7 жыл бұрын
how many miles was on that truck
@flmmaz
7 жыл бұрын
I forget now, but it was over a 100k.
@StorkTransportLLC
7 жыл бұрын
What do you use to lube the locking hubs?
@flmmaz
7 жыл бұрын
What ya be speaking about?
@StorkTransportLLC
7 жыл бұрын
When you pull the locking mechanism out of the hub, they have some sort of grease on them. Anything special or just high temp bearing grease?
@flmmaz
7 жыл бұрын
Nothing special, just regular.
@lesliemiller8340
6 жыл бұрын
Is there another part to this? This one says tear down only.
@flmmaz
6 жыл бұрын
No. sorry I did not have time to film putting it back together.
@gerardobemcomo2706
5 жыл бұрын
Because he was blabbing off and F%^KING around. At least edit the footage but dknt say you didn't have time when half the video was talking about your classes and how some dude was smacking a rotor off...
@Yoopee-ld1xo
4 жыл бұрын
Little details are left out while we watch him use airtools and talk ....little details lacking
@flmmaz
4 жыл бұрын
Yep, I agree, pretty lame video, I didn't have time to get proper footage.
@marioncobaretti2280
5 жыл бұрын
we definitly suffer up north....lol......rust.....rust and more rust !
@stevemazzarella9259
7 жыл бұрын
No penetrating oil no torch I'm jealous.....
@flmmaz
7 жыл бұрын
lol
@YLTMauto
6 жыл бұрын
😂😂😂😂😂 lets see you do that up north.
@robkwiecinski5671
5 жыл бұрын
Yes
@Mebob2001
7 жыл бұрын
.... you son of a bitch...... "lets see you do that in the north" was a stand at me i know it... haha thanks for the laugh buddy,
@flmmaz
7 жыл бұрын
You know it!!!!!!!!!!!!!!!!!!!! LOL
@asconstruction4146
6 жыл бұрын
As the shop turns blah blah blah funny no one realized you had your camera on!!!!!!
@ericdowner5589
7 жыл бұрын
"There's two axels" lol
@flmmaz
7 жыл бұрын
😃
@D4x4Bronc
7 жыл бұрын
hate jobs with gossip like that. not good bros.
@flmmaz
7 жыл бұрын
Gossip? That what'n gossip, that was a conversation geared toward poking fun at my co-worker who I was conversing with (who is good for it btw). The person we were talking about might as well be a fictional character in a novel. whom I will most likely never meet. Now if you want some gossip I can set the camera up in the front of the shop, all you can handle. Either that or I can take it to any local church on any typical Sunday five minutes before the sermon. lol
@wysetech2000
7 жыл бұрын
I kinda enjoyed the drama. Was a little hard to hear. In the north you usually have to beat those hubs out. Lots of BS in dealerships as there are so many personalities there.
@screamindemon811
7 жыл бұрын
not only that but if there wasnt any chatting around the shop we never would have heard of that story Brad told about the guys who took the for sale sign off the house and re-sold that car to all those different buyers in that scam. I still laugh my ass of at that story, I never heard of that scam before
@rdp2370
7 жыл бұрын
How far away from part 2 are you from releasing?
@flmmaz
7 жыл бұрын
Sorry to say that the only footage is of the tear down. I just didn't have time.
@D4x4Bronc
7 жыл бұрын
less ball peen hammer, more sledge hammer. get you a nice USA one from.sears
@flmmaz
7 жыл бұрын
I know, I need to upgrade, but I am cheap. Plus that lift makes it a challenge no matter what you got.
@D4x4Bronc
7 жыл бұрын
flmmaz cheap with surprise points or coupons. buy less snap on.
@leroybrown9828
5 жыл бұрын
You guys did more talking than anything and showed nothing waste of time sorry to tell you that
@flmmaz
5 жыл бұрын
I apologize myself for wasting your time as this is not a how to channel.
@jpayne1630
3 жыл бұрын
South wod be
@mobilemechanics6565
4 жыл бұрын
Hard hits with a wood handled dead blow brave man lol.
Пікірлер: 80