Hey quick question here, If you feel like the rear height is too high of your H&R Sport lowering springs, is it possible to put some BC coilovers weight ajuster on top of the spring to manually lower the rear by yourself with coilovers ranch?
@thand6969
7 жыл бұрын
will be DIY'ing very soon. Any chance you have a list of torque specs for each bolt? Would be very helpful. Thanks!
@xxxae_
4 жыл бұрын
Tyler Hand hey man I know this comment is very old and u may not even have a bmw anymore but did u ever get those torque specs ? 😂
@Scoobyxxxsnax
4 жыл бұрын
@@xxxae_ hey. theres a post on bimmerpost under f30 thread that has all the specs from an official bmw service manual i seen a while ago
@alexpyshnyi771
3 жыл бұрын
@@xxxae_ do you have the torque specs ??
@matthias_372
5 жыл бұрын
Just to let you know. The process works exactly the same on a F36 the only difference is that the torx on the rear axle is bigger, you need a different key
@jarrettbarnett7656
7 жыл бұрын
Would love to see a video showing the jacking points (besides the 4 square ones)
@Notawhitef30
3 ай бұрын
This is hands down the best dyi tutorial I've seen far f30 spring install so far. Simple, straight to the point, no sidetracking, no opinions. Just tech talk.
@heromeng2948
4 жыл бұрын
Hi Brian, it's very enjoyable to watch your DIY. I am working on the same project for my roommate's F30 335i. Do you know the torque specs for those bolts? I did some research showing that: everything looks OK but the three 16mm bolts which are only 28NM. The tightening specs look too low. If you know what exact torque spec, please let me know. Thanks! Strut to strut mount nut: 16mm bolt 44NM nut 32.5ft/lb Strut mount to vehicle body: 3X16mm bolts 28NM 27.7ft/lb Strut assembly to steering knuckle: 18mm bolt + 16mm nut 100NM 74 ft/lb Suspension brace: E18 bolt 56NM 41ft/lb Sway bar link to strut assembly: 16mm nut 56NM 41ft/lb
@mai4397
4 жыл бұрын
I want to lower my bmw but heard that its bad to mess with the x drive setup? Has anyone run lowering springs on an x drive and what’s your experience with longevity and reliability with shocks etc...
@jacksampson7711
7 ай бұрын
Ha! What a blast from the past. This showed up as a recommended video on youtube. Look how far Brians has come. Congrats!!!
@Ericpittman13
8 жыл бұрын
What torque settings did you use when replacing the bolts?
@skreech01
7 жыл бұрын
the rear is easy..... the front is a nightmare
@leslongines2638
7 жыл бұрын
ร๏๓є๒๏๔1 it looks the front is also easy
@Onizukachan915
4 жыл бұрын
It’s not e34 easy, where you can remove the sway bar end links, unbolt the strut rod, and drop the suspension so far the spring unloads and the strut pivots out for easy spring removal, but it is no hard than my e46 either.
@alexflores5241
6 жыл бұрын
I have 2015 F30 and I am thinking of lowering it. Thanks
@taibanh5046
6 жыл бұрын
How does it drive with stock suspension. Is the xdrive same as e92 xdrive thanks
@shardsofcontent4829
7 жыл бұрын
I finally installed the H&R Sport Springs with Bilstein B8's on all 4-corners of my 335. Absolutely unequivocally brilliant result. Costs a few bucks up here in Canada but so worth the time and investment. I was a bit worried after your anti run-flat post. I put standard Pilot Sport A/S3's on the car and like I said ...
@KiesMotorsports
7 жыл бұрын
Hi, Rob. Awesome, how's the ride?
@shardsofcontent4829
7 жыл бұрын
The ride is slightly stiffer than stock but not a problem at all when driving around. My wife said "very smooth" today, so I think we have a verdict. Expansion joints on one of our older bridges sharply remind me that I have a Sport suspension though. In general I think the 225/45ZR18's buffer a certain amount of road texture. Two really noticeable things are the drop in ride height and the swift immediacy of steering input. This is what a 3-series should feel like.
@tuned_auto
5 жыл бұрын
Has your verdict changed a year later? Did you use the stock end links?
@kevinrivas7594
5 жыл бұрын
How did you fixed the negative camber?
@Gamer-co5kl
8 ай бұрын
This guy always has the best camera angles and best explanations. It’s deceiving because he makes everything look super easy 😂
@yungd3mon871
3 ай бұрын
So today I lowered my f30 and the rear passenger tire is tucked more than All other tires… any ideas what could be happening
@VVH1997
3 жыл бұрын
Really nice to see where you started this channel. congratz on learning so much and growing your channel :)
@WindyTubbis
23 күн бұрын
BMW F30 Rear Shock Mount Bolts = 28Nm or 20.7 lb-ft of torque BMW F30 Lower Rear Shock Bolt = 100Nm or 73.7 lb-ft of torque BMW F30 Rear Knuckle Bolt = 100Nm or 73.7 lb-ft of torque BMW F30 Front Knuckle Pinch Bolt = 44Nm or 32.5 lb-ft of torque, plus 90° BMW F30 Thrust Arm Mounting Bolt = 100Nm or 73.7 lb-ft of torque BMW F30 Control Arm Mounting Bolt = 100Nm or 73.7 lb-ft of torque BMW F30 Lug Bolts = 119Nm or 88 lb-ft of torque
@GuerillahFU
6 жыл бұрын
Thanks for the great instructional video. In the future, it may be nice to list the tools needed in the description. I'll be using this guide soon, thanks.
@Dreeveryday
4 жыл бұрын
Do you need an alignment after installing these?
@junmaecarlo
4 жыл бұрын
Any suspension mods definitely needs an alignment check asap. I myself bought super sports for my F30 vs. the H&R sport springs in the video and if you’re especially doing a diy install, it’s highly recommended.
@genoksreye7190
5 жыл бұрын
Thanks for the video. What is the torque settings on the top strut bolts.
@euancruickshank8837
6 жыл бұрын
Does anyone know if this is similar to doing the same on an F20 (M135i)?
@alexflores5241
6 жыл бұрын
Hey isn’t best to replace the shocks with ones that are suitable for lowering springs? Let me know. Thanks.
@sefdestruct1
3 жыл бұрын
It is but mostly if you buy cheap springs
@tuned_auto
5 жыл бұрын
Can I use the stock end links with the H&R sport springs? I also have Bilstein B8s if that makes a difference.
@FrenchValleyAirport
5 жыл бұрын
yes you can, changing springs does not change the mounting point of the end links on the strut body, you're good to go.
@beloandcopp
4 ай бұрын
So what are the torque settings for the rear 2 bolts that connect the hub and the rear damper, The torque specs for the front collar bolt and top mount bolts. If you don't mind me asking
@awesomepokemon77
3 жыл бұрын
I just did this to my car, great video by the way. Exact same springs. Did you have any issues with your axles at all? How did your suspension hold up? I’m just bracing myself for all the issues that may arise lol
@eugene1822
2 жыл бұрын
My end links went started making noise after and my steering rack developed a loud clinching noise
@Litosminishop
4 жыл бұрын
Thanks for the tutorial. Just did my f30 suspension today And this tutorial was on point. 😁👍🏼
@jakemaddox76
Ай бұрын
Would this be the same procedure (socket sizes and all) on an F30 330i?
@FreshD9191
4 жыл бұрын
Do you have a link of your front lip? Looks Great
@kingmonkey88
6 жыл бұрын
I always find that last large 21mm bolt on the rear lower wishbone the most difficult to get in as the knuckle bushing never aligns straight to get the bolt through. I noticed that you jacked up the wishbone under the spring. I'll give that a try next time.
@CorneliusVeee
6 жыл бұрын
I cant get that bolt in. How did you do it?
@HarithAhmadDaud
2 жыл бұрын
Hey man, can you do me a favor of measuring the outer diameter and length of the front and rear springs? My car is a really old car and there is NOTHING in the market for my car. I've measured its OD and length of front and rear springs and I found on some UK retail website that the H&R purple sport spring for bmw f30's measurements come close to the springs I'm currently using. I just want to confirm with you if that website is legit. If you decided to help me you'll be doing me a solid here. Thanks in advance man, cool channel.
@gabealmeida1234
2 жыл бұрын
Hey Brian! I just finished mine. And I got a traction control light and an abs and now a check engine light. Have you heard of this problem happening. It’s a 2015 328i xdrive
@TheKdizzler
2 жыл бұрын
I had to replace the entire roll over strut arm (you one you removed 2 bolts from), the final bolt removed was by the subframe. I cannot realign the knuckle arm bolt which was a skipped scene here, the jack goes from being by the knuckle to under the spring. Any suggestions?
@juniorschouten3448
4 жыл бұрын
Thanks alot Kies Motorsports! Just lowered my f30 with KW springs with your DIY. But without the power tools it requires lots of strength but it worked. My f30 with 19 inch bbs lm looks much better now.
@ryandefeo9222
Жыл бұрын
Sup Kies, I have a f30 340xi, H&R SS install should be no different than the install done here correct?
@robertbaptiste659
3 жыл бұрын
Hey brain after I install the springs I’m now getting a code chassis stabilization erro 2017 330i 🤦🏾♂️
@louispatroons4485
4 жыл бұрын
cant you just leave the front shocks hanging in and undo the top bolt from there, unbolt the top of the spring and insert new spring and compress the spring by jacking up the assebmbly?
@oceang60smith38
4 жыл бұрын
I am installing B 14 Bill Steen coil overs on anF 30 X Dr. and I want to know if it’s OK to reuse the original bump stop. In the rear. The certificate that comes with the kit says to reuse it but it seems a little bit long. What are your thoughts? Sorry I’m text speech iso the words are a little funny.The certificate that comes
@MisterMili
4 жыл бұрын
Do you have to upgrade your shocks as well? If so, what kind is recommended?
@Ratalala
6 жыл бұрын
Your video was helpful 👍🏽 Same setup here, but with the stock shock absorbers when i hit a hole in the road the absorber hits it self from being shortened and make a big boooom ... So i ordered the Bilstein B8 for front axel today ;)
@kencardona3653
5 жыл бұрын
dansobolanu, Did you get to install the Bilstein B8? if so, how does the ride compare? thanks in advance.
@GeckoDays
3 жыл бұрын
Been needing this answer back, about to order brand new struts + mounts. How’s the ride? I have m package + 19’ , would like to hear the feedback on the bilstein
@kalemgartin2486
2 жыл бұрын
Think they would be any rubbing while running 19x8.5 in the front and 19x9.5 in the rear
@hmktemp2842
7 жыл бұрын
I always enjoy watching your videos. You make things look so simple.
@KiesMotorsports
7 жыл бұрын
Thanks!
@joebiscuit2005
Жыл бұрын
Hello. I have a BMW 2018 330i this is a fit?
@mrcsmlsq
2 жыл бұрын
is this the same process for a 2014 335i xdrive with m sport package?
@taibanh5046
6 жыл бұрын
I heard lowering springs on stock suspension on xdrive ride really bad
@perakojot6524
5 жыл бұрын
Depends on the springs H&R are makes it awful, AC Schnitzer OTOH are great.
@MUHLMEDIA
5 жыл бұрын
@@perakojot6524 What makes it awful? Are you referring to non-Msport Vs Msport suspension?
@kencardona3653
5 жыл бұрын
I have to agree with the H&R making the ride awful on an XDrive, I have them installed on my F32 XDrive and looking for another alternative. The look is amazing but any bump on the road will make you cringe! Would love to hear what anyone out there has done to rectify this issue........
@ericcruz7836
5 жыл бұрын
Ken Cardona just installed h@r springs on my 2011 335i xdrive and the car hits very hard with my snow tires still on. Scared to change over to my Summer wheels and tires now.
@jlglol
6 жыл бұрын
Thank you for this video. My grandfather and I lowered my f30 on k&n sports in only 3.5 hrs. Quicker than I honestly expected
@KiesMotorsports
6 жыл бұрын
Awesome job!
@jlglol
6 жыл бұрын
Kies Motorsports one last thing, are ur m wheels 18s or 19s? Thanks!
@DaViDoFf4444
4 жыл бұрын
Does this car have a m-sport chassis ? So how many cm is the lowering? Are your rims 18 or 19 inch ? Thanks
@stephenbarber8704
5 жыл бұрын
Your channel has saved me so much cash. Thank you thank you thank you
@tohest
6 жыл бұрын
what size on the go-through-socket to release the droplink?
@kylegriesser4281
7 ай бұрын
will this be similar on an f36?
@bmwman540
5 жыл бұрын
Just completed this job today with AC Schnitzer springs. Just to help. we noticed that the drive shaft can sometimes pop out when the front strut assembly is taken out. This makes it really difficult to put the new strut assembly back in. Make sure that the drive shaft is fully engaged when strut goes back in . Also some of the bolt sizes and numbers may vary between models. I was working on 435d EU spec. Otherwise a great video. Many thanks.
@olejohanwaago6054
5 жыл бұрын
Are there really any need to loosened the whole assembly in the front? Why not just loosened the one nut on the top? And lower it down with a jack?
@firstname7780
6 жыл бұрын
Too bad H&R do not work with the F30. Common issues are the bump rate (esp with M Perf struts) and bottoming out. Contrast, ACS and Dinan are truly stiffer than OEM, so lower suspension but no longer hit specific locations where the car would bounce and tap the asphalt.
@BashxSaiyan
2 жыл бұрын
Do the springs affect the ride comfort? I have an xDrive and my f30 is surprisingly high.
@sammynice6253
3 жыл бұрын
Nice video I bought bmw coils and cant compress it enough to get the gasket on 😬
@MrBMW83
6 жыл бұрын
Were can i get a good set of 4 springs for my F30..?
@platinumzs1k
6 жыл бұрын
Where are you putting both of your "U" jack stands? I cant tell where to put them.
@adamandrew292
6 жыл бұрын
Where did you get that spring compression tool you used for the front? The one you used looks very safe with the c clamps, there is no way for the spring to slip. Do you have a link? Also does X-drive, or the ability to switch suspension modes effect this job at all? Thanks.
@LeonardoCostaUSA
3 жыл бұрын
Great video man!! I was wondering if I lower the front suspension of my F15 BMW 2014 would the rear suspension follow the front by itself since it's self leveling?
@saistylezwigartistry1616
3 жыл бұрын
I’m thinking if do them same. I don’t want to touch my rear since it is already lower
@eduardozelaya9168
6 жыл бұрын
Liked all your videos very helpful. Need help n hard to find answers F32 xdrive with adaptive m suspension can I use h&r springs or what would u recommend Any comments would be greatly appreciated thanks.
@Maksezzy
2 жыл бұрын
Torque specs would have made this video the nicest.
@intermichael100
8 жыл бұрын
Man it looks hard.. made me wanna pay somebody to do this lol
@KiesMotorsports
8 жыл бұрын
I'll do it, ha
@jeremywhite845
3 жыл бұрын
I'm super late to the game, but what is the wheel/tire size and setup?
@Hernjona
3 жыл бұрын
gonna do this but cant find any go though sockets
@nancycamacho4441
7 жыл бұрын
what website is the most reliable and recommended to buy these from??????? thanks
@bmwm4171
8 жыл бұрын
What size wheels width and offset I already lower my 328i an 1.5 inches on eibach
@jeffersoncoro87
2 жыл бұрын
What’s the torx socket to the open wrench called
@fernandoalvarez3
5 жыл бұрын
So much easier if you leave the front strut attached to the tower, and just push the knuckle down. Instead of trying to pull the strut out of the knuckle.
@MUHLMEDIA
5 жыл бұрын
Work smarter! I like it! I'm assuming if you have enough ground clearance to pull the springs down under. Is the removal/installation similar to a 2014 X3 xdrive35i Msport? Newb DIY'r asking? I bought a set of H&R and I'm debating to take it in to my mechanic for $600(quoted high as $1000) vs DIY.
@fatelrekon
4 жыл бұрын
Which springs can i use for 2015 rear wheel 320i?
@evanmccarley4850
3 жыл бұрын
Great video. Should I expect this setup on a F30 335i rwd?
@thearypich3401
6 жыл бұрын
Thank you for the awesome video! Just picked up myself an F30i Xdrive. I’m curious, how’s the ride quality after changing the springs?
@jonnyk-uk662
4 жыл бұрын
🙋🏼♂️Bagsy doin the back ones 👨🏼🔧
@AntLive29
2 жыл бұрын
Really helpful video. Thanks
@Alikhan78611
7 жыл бұрын
Hey Bryan, could you please confirm if I need 6 or 12 point sockets for this job? I am just buying all the tools and I m bit confused. Thanks!
@KiesMotorsports
7 жыл бұрын
for which part?
8 жыл бұрын
VMR WHEELS? Which size of tires are u using? Ty
@B15SDMDESIGNS
7 жыл бұрын
Brilliant video! What would make it priceless is if you could include the torque settings for each nut/bolt. That information is very difficult to find for some.
@KiesMotorsports
7 жыл бұрын
Sorry, it's been a while, but I believe there was another comment on it with a post to BimmerPost or BimmerFest with the info
@1Sturdy5_
11 ай бұрын
Great video. Thumbs up
@robertbaptiste659
3 жыл бұрын
After installing the springs Did you get the error code with the traction control
@gabealmeida1234
2 жыл бұрын
I just finished mine and I got the code. Where you able to figure out what happened?
@MUHLMEDIA
5 жыл бұрын
Is the install the same on a F25 xdrive325i? #newbBMWdiy
@lykeomgkevin
7 жыл бұрын
after owning an e46 and an e92 now onto a f30 all things just get more complicated. I am cursing at my screen just watching you do the front end of this haha. thanks for the videos man! ps. love your car, i have a f30 14 328i xdrive sportline and i'm doing that front lip and vinyl wrap the back of the sportline from your videos!
@KiesMotorsports
7 жыл бұрын
Thanks! Ha, yea, they aren't what they used to be. Good luck with it and let me know if you need help with something. Bryan
@JFISH222
7 жыл бұрын
I CANT GET THE FRONT 21 mm bolt to line up when reassembling the back,
@JFISH222
7 жыл бұрын
Kies Motorsports I finally got it haha it put up one hell of a fight. Love your videos man, very informative and to the point.
@bigjose8358
2 жыл бұрын
No Audio ?
@jayfrmdaland4683
3 жыл бұрын
Did u need a wheel alignment after this?
@josephliu3721
7 жыл бұрын
Where can I buy those aftermarket wheels? They look beautiful in black or bronze, I have 2015 328i xDrive, much appreciated!
@KiesMotorsports
7 жыл бұрын
Hi, I'm not sure, I bought them used
@teitma
7 жыл бұрын
They look like "Outlaw Anarchist" replica wheels of BMW's original E46 wheels "Styling 163", because they're missing the BMW writing next to the m logo. All other numbers on the outside are perfect fakes...
@cubmixit
4 жыл бұрын
Great video! How is the ride compared to stock spring?
@cardcrash
6 жыл бұрын
Do the front struts come away in the same way with the adaptive suspension models?
@hoooosifa
7 жыл бұрын
Where can I find that tool for the compression fitting? Instead of using a flat head screw driver like you did.
@KiesMotorsports
7 жыл бұрын
Something like this is what you need, but I haven't personally tested this one: amzn.to/2vE7vp6
@Rolus90
5 жыл бұрын
Hey, on this car is a adaptive suspension or normal suspension?
@jcoach3064
2 жыл бұрын
I’m going to put mine on today
@DoopSpeed
7 жыл бұрын
Kies M. Do u think u can help me installed does spring?
@borinvlogs
4 жыл бұрын
The houses are so nice in your area. Only very few millionaires can live like that here in UK 😂
@mike786551
3 жыл бұрын
Almost all houses in a middle class area in the US are like this lol. We have the advantage of a very low cost of living and lots of area compared to Europe
@marlonfarquharson1419
5 жыл бұрын
am a car guy with a bmw but you guys are amazing a learn a lot of you guys two
@fondoo
8 жыл бұрын
how long did it take you to install those springs? how long do you think a shop will take to install it? most quoted me 6hr job
@KiesMotorsports
8 жыл бұрын
Hi, took me about 4.5 hours, but I did it 90% by myself, with only the tools shown
@KiesMotorsports
8 жыл бұрын
Sorry, I didn't answer the second part of your question. I think 6 hours has some buffer built into it, so I wouldn't say it's out of the question, but if they are using air tools with a lift, it should be quicker, based on how long it took me to do mine. Just curious, how much are they quoting you?
@fondoo
8 жыл бұрын
about $650.
@chungtran8595
6 жыл бұрын
Does the X drive and RWD use the same instruction?
@TheDammertmuelle
7 жыл бұрын
where do you find the right torque specs?
@TheAutomotiveFanatic
8 жыл бұрын
I just bought a gorgeous EB 335i and your video will come in very handy once I start working on the suspension. Thank you for making the video.
@KiesMotorsports
8 жыл бұрын
Awesome, good luck with it!
@TheAutomotiveFanatic
8 жыл бұрын
Thanks again for the video; it provided a great guide for me to install H&Rs springs on my F30 this past weekend. The only trouble I ran into was the alignment of the rear control arm to the brake hub assembly. I simply could not get the pivot point perfectly aligned so a mechanic friend successfully did it for me. Do you have any videos on DPs or upgrades for the FMIC?
@KiesMotorsports
8 жыл бұрын
Great, glad it helped! I don't yet, but I'm trying to parter with a few companies to do some new videos, but no firm dates yet..
@XxS1l3nTxa1Mx
4 жыл бұрын
What is the point of the springs
@hlb0620
6 жыл бұрын
What kind of wheels and color are those?
@jesuscruz5615
8 жыл бұрын
Do you know if there are cpe charge pipes for your car?
@sandytaco3327
7 жыл бұрын
Can you tell a huge difference in handling??
@rikverma2415
7 жыл бұрын
Hey Brian I recently lowered my 2016 320i with H&R super sport springs and I've recently started noticing some clunking noises whenever I go over a bump, big or small. Double and triple checked everything and nothings loose and everything seems to be holding up. What would you think is causing the clunking noises? I've had a few people tell me it might be my top hats but that doesn't make sense to me as the car is basically new still.
@KiesMotorsports
7 жыл бұрын
Hi, my first question is are you positive they are the right product code for your car?
@rikverma2415
7 жыл бұрын
Yes I'm positive. 28877-2
@paulm.527
6 жыл бұрын
I'm experiencing this too Brian and Rik. Installed the same springs on my 2013 F30 and now I hear a hollow knocking sound on the front left. Retightened all bolts and made sure everything is where they're supposed to be. I notice mine occurs when the shock drops on an uneven road surface, not upon engaging/approaching a taller bump on the road.
Пікірлер: 230