Thank you i just bought a f super duty and it needs this done, glad you showed this as i now know all the parts needed thank you very much for your time, it helped me greatly.
@chekelley6861
Жыл бұрын
I’ve done a ton of these on ambulances. You did it the correct way by packing grease. Not everyone does that because it’s also lubed by diff fluid.
@capellan4196
6 ай бұрын
Excellent video!!! Thank you. Waiting for more videos.
@Bill-ts9zv
Жыл бұрын
Sometimes you go faster than I can watch. Good job and pays to have the correct tools.
@emodayscline2186
3 ай бұрын
Thank you again i can find the sizes of bolts parts ect myself, hell I'll even figure out the tools i need so you dont have to worry about that too. Great video
@JamesL5150
10 ай бұрын
Quick question, your video was a bit fast for me to tell and I haven't taken mine apart yet to see, on the Hub nut, you used that 8 sided socket, can you not also use the 2-3/4 4 lug spindle nut socket? I have seen other videos where they used that, now I am wondering if I need different tools before I start....I don't have a second vehicle to go get different stuff once I start. I have the same 2019 F450 King Ranch 4x4 6.7L Diesel. Definitely a very nice, well detailed video. Thank you! The only thing I might suggest is that you list part numbers and tools, etc in the description. I know you mention and/or video everything but it would be nice to read them as well. I'm thankful to finally find this video with the proper size bearing, race, and seal installer kit, after having bought two already that did not include the right sizes....GRRRR
@raincitywrench117
10 ай бұрын
You're welcome 👍 I don't know if you can use a four lug socket. Picked up mine on ebay for around 25 bucks. *Carlyle TOOLS by Napa 3/4" Drive 3-1/4" OCT 2449 NUT SOCKET* Need 3/4 to 1/2 adaptor if you don't have 3/4 ratchet. You are not the first to mention that, I need to do better at listing tools in the description.
@ShelbyClay-j5m
8 күн бұрын
What is the part number for the Lisle set for installing the inner race. The hub nut socket you said is a Lisle 2442 that is a 8 sided nut right which I think is different from the F350 correct??
@RoRo-kc8zv
11 ай бұрын
Come on 10k 🎉
@carlmckeenan6906
4 ай бұрын
Thank you
@raincitywrench117
4 ай бұрын
You're welcome!
@darrelllindsay8656
7 ай бұрын
Thank you!
@raincitywrench117
7 ай бұрын
You're welcome!
@jayhanson4797
7 ай бұрын
What kind of grease do you use for the bearings...the grease..does do anything to the gear oil lude.
@raincitywrench117
7 ай бұрын
Just standard high pressure wheel bearing grease. It doesn't hurt anything and Ford recommends if installing new bearings.
@Farmtractorrescue
9 ай бұрын
I assume all these steps arent needed for just a pad replacement?
@raincitywrench117
9 ай бұрын
It will probably develop a loud squeak if only the pads are replaced. Just a heads up
@kenj.8897
Жыл бұрын
👍
@elijahparedes9172
10 ай бұрын
Does that same socket fit a f550?
@raincitywrench117
10 ай бұрын
It should. Ford workshop manual shows a Dana M300 in both the 450 & 550
@davidraduziner8732
4 ай бұрын
WHY NOT TELL EVERYONE WHAT SIZE THE DAMN BOLTS ARE?
@politicallyincorrect9027
7 ай бұрын
You are supposed to be showing how to do it not showing how fast you can do it.👎
Пікірлер: 22