Can you make video for adjusting the belt before I do but it takes too much time .. thank you boos 🤗
@Rajeshpg1506
2 жыл бұрын
Ok sir.
@vivapalestine9063
2 жыл бұрын
@@Rajeshpg1506 thank you ❤🤗
@hampasser
2 жыл бұрын
Doors open and close frequently on its own..even while running too.. What's the fault
@Rajeshpg1506
2 жыл бұрын
Actually, in many cases during the running in between the doors will be open . It is the mainly earth issues or leckages from the COM DO DC. so i have faced so many places like this , I suggested to customers 1. Remove DO wire and check. 2. Remove the Total 5- pin connector once and check. 3. Remove the total COM DO DC wires and take 3 new wires and conncet them from controller to direct drive then check once. I think the problem will be slove .
@hampasser
2 жыл бұрын
@@Rajeshpg1506 thanks for the response. Will try the same
@Rajeshpg1506
2 жыл бұрын
@@hampasser 👍
@anulmohammad7405
3 жыл бұрын
Centre opening dip switch ..which numbers ON and OFF .......
@Rajeshpg1506
3 жыл бұрын
Thank U for your reply. For Center Opening = 1, 4 should be Off always. & 2, 3 = ON . But in that site sometimes when the Door opening Close LED shows. And Door close time Open LED shows. For that just Interchange the DIP - 3 . Otherwise just keep 2 , 3 should be ON only.
@Rajeshpg1506
3 жыл бұрын
Thank U for your reply. For Center Opening = 1, 4 should be Off always. & 2, 3 = ON . But in that site sometimes when the Door opening Close LED shows. And Door close time Open LED shows. For that just Interchange the DIP - 3 . Otherwise just keep 2 , 3 should be ON only.
@prakashprakashnaik202
3 жыл бұрын
Wirening video telugu link
@mrrohan6396
3 жыл бұрын
How much time will it take for one open and close of door
@Rajeshpg1506
3 жыл бұрын
Thank u. Open speed = 200 to 700mm/s. Close speed = 150 to 400 mm/s. Safety force = 60 to 250 N. Adjustable.
@rajanraj-dc8nu
3 жыл бұрын
Hai sir.. During closing time having noise.. How to rectify the issue
@Rajeshpg1506
3 жыл бұрын
Thanks for your feedback. 1..During the closing we need to check the noise from motor side or closing roller side. 2. Check the belt is tension. If it is full tight just loose as per condtion. 3. Do the automatic tunning once. If you need check that my tunning procedure. 4. Check the mechanical side whether your doors are having alignment properly.
@anulmohammad7405
3 жыл бұрын
Kiya problem ho sakta hai
@Janete6860
3 жыл бұрын
If I modify speed i need to auto adjust agin ?
@Rajeshpg1506
3 жыл бұрын
There is no need of Auto adjustment again . But if u want to do that's ur whish.
@nagababumasarapu8902
3 жыл бұрын
👌
@sunilraj22068
3 жыл бұрын
Hi good initiative... but your explanation is wrong, for center opening and left opening DIP switch position are same, and for Right side opening the RIP Switch position is different
@Rajeshpg1506
3 жыл бұрын
Thank you fr your feedback sir . But for center opening and side opening it was the depending on the coupler postion we need to check .we can't say direct. What i said that was absolutley right. If you have any query let me know . My number 7045938131.
@anulmohammad7405
3 жыл бұрын
Sir help me Door close hote hi return open ho rha hai door
@Rajeshpg1506
3 жыл бұрын
Iskaaa main problem kabhi door closing time mee coupler barabar close Onaa chayaiye.. nai thoo return open othaa. Check the coupler postion barabar. Nai thoo check the sensor conncetion.
@chinamallisivakumar1486
3 жыл бұрын
Copler close avvadam ledu sir
@Rajeshpg1506
3 жыл бұрын
Thank u for your message. First nuv controller nundi vachee DO DC COM . Wires thisesai .auto adjusting chey drive . Video chusi chey appudu kida coupler close ayyava pothee . Safety 54 No. Chudu .adhi montham + side thippi . Malli okasari Autoadjustment chesi . Chudu. Ok avthadi.
@mrrohan6396
3 жыл бұрын
Type of motor used ?
@Rajeshpg1506
3 жыл бұрын
For FERMATOR we are using PMSM motors.
@mrrohan6396
3 жыл бұрын
@@Rajeshpg1506 Why door contact switch is used?
@mrrohan6396
3 жыл бұрын
What is the use of it
@mrrohan6396
3 жыл бұрын
What if the door contact switch fails
@Rajeshpg1506
3 жыл бұрын
@@mrrohan6396 To get the Safety's and close the safety circuit.
Пікірлер: 48