Just a little bit different thread... You can make it fit. Thank you Bryce!
@brycewiborg8095
3 ай бұрын
I have a thread gage in the tap, and die set. I'm going to check if I can figure out something. I still haven't found the nut I dropped. Thank you Ed.
@Murphyslawfarm
3 ай бұрын
G'day buddy
@kenbarkdoll7252
3 ай бұрын
Good luck with that job. Hope you find the right thread count nut
@brycewiborg8095
3 ай бұрын
Eventually the original will show up. I heard it fall. It's been years since the floor was this clean. Thank you Ken.
@Kevscancave
3 ай бұрын
Good Afternoon Bryce 👍
@brycewiborg8095
3 ай бұрын
Good afternoon Kev.
@Kevscancave
3 ай бұрын
@@brycewiborg8095 at first, I was thinking it might be left-hand thread, but it seems like you’re getting it on there pretty good. It just doesn’t go all the way!
@brycewiborg8095
3 ай бұрын
@@Kevscancave Fortunately this is the right had side. Eventually I will find the nut I dropped when I took the wire brush off. I noticed that I have a thread gage in the tap, and die set. In a while I will check the thread count.
@Murphyslawfarm
3 ай бұрын
G'day Kev
@farawayfarm2520
3 ай бұрын
I was using the same Diamond adjustable wrench today. It usually lives in the 50 tool box in the summer.
@brycewiborg8095
3 ай бұрын
That's actually what I used on the tap. I put the handle on for show. I like the Diamond tools. Thank you Will.
@farawayfarm2520
3 ай бұрын
@@brycewiborg8095 I used mine on a tap too. Pipe tap for a grease zerk on the rake gearbox.
@Murphyslawfarm
3 ай бұрын
G'day Bryce
@brycewiborg8095
3 ай бұрын
@@Murphyslawfarm G'day Murphy.
@countryguy828
3 ай бұрын
Closest metric would be 12mm at .472 or 13mm at about.513 however British Whitworth could be 1/2-12
@brycewiborg8095
3 ай бұрын
Thank you for the information. I keep looking for the one I lost. There are still a few places to check. Thank you Dave.
@countryguy828
3 ай бұрын
@brycewiborg8095 another side note. British Whitworth is 55degree whereas we are used to 60degree.
@brycewiborg8095
3 ай бұрын
@@countryguy828 I suspect this was made in Taiwan. It's a Menards brand, but old enough that it doesn't have a country of origin marked.
@southtexashay777
3 ай бұрын
Those nuts were half the thickness than the one your holding Bryce. I wonder if the Grinder Nut 5/8-11 would fit.
@brycewiborg8095
3 ай бұрын
It sounds worth a try. I still haven't found the one that I dropped. We have fastenal in town. Thank you Louie.
@brenterickson1695
3 ай бұрын
That's not a old grinder, it was built during our time...Are you saying we're old Bryce? 😂😂😂
@brycewiborg8095
3 ай бұрын
I was surprised that the surface is steel. I bought it used to replace a plastic Black & Decker. I had a Belsaw I really liked, but someone offered more than I had invested. Thank you Brent.
@jankotze1959
3 ай бұрын
Hi Bryce, I bet that is metric, hope you come right
Пікірлер: 25