Brings back great memories. I had the 904 in my 72 Duster. One of the first trans I took apart back then. No you tube etc. Only the books and brain matter
@tattoosteveneo
2 жыл бұрын
Thanks for these videos. I’m going to use them to rebuild my trans!
@MrDurandal25
2 жыл бұрын
Very nice basic build on this. 727's are a fantastic transmission!
@anormalperson6886
Жыл бұрын
Thank you,. You really do make it look easy. I'm going to try it on my 727.
@blakenorman4822
Жыл бұрын
How did it go, going to try rebuilding mine
@johnriddle149
2 жыл бұрын
I’m actually in the process of rebuilding a 5.9 for my Duster and your videos are very helpful. I haven’t messed with transmissions much but you make it look somewhat easy. Thanks for the video.
@YoshimoshiGarage
2 жыл бұрын
If you're capable of rebuilding an engine, you can do a transmission. I actually think a transmission is a bit easier. Just take your time and be deliberate about checking and measuring every piece, which you have to do on an engine as well.
@pinksax
4 ай бұрын
Good info, same trans in my old Monaco.
@franciscotorres6907
Жыл бұрын
Video bien detallado y bien especificado 👍
@1607rosie
2 жыл бұрын
Love the 727 . A strong transmission and pretty simple compared to others. Learned there are some trucks to make them stronger.
@jorgeh0000
9 ай бұрын
Amigo que buen video, que buena explicacion, usted es todo un profecional, muchas gracias y un gran abrazo desde Venezuela.
@jodaddysdodgegarage3533
9 ай бұрын
Thank you for showing us how to do this!
@sith4mmer558
2 жыл бұрын
Starting on a 46re rebuild next week. Great vid!
@mrs.t7056
Жыл бұрын
Great series. Thanks for posting.
@Torquemonster440
Жыл бұрын
Excellent, Excellent series. Well done !🍻
@bradsrestorations1085
10 ай бұрын
Excellent video. Thank you.
@Monaco-BuilditFixitDriveitEver
10 ай бұрын
Thanks.
@HowardWilliams-1313
7 ай бұрын
You forgot to tighten the sprag set screw.
@user-oh3hr7lo8t
6 ай бұрын
Excelente video,lastima que no es en español, felicidades
@langstonjones69
2 жыл бұрын
So, I have two spare 727's that I bought extremely cheap and would love to go through one before installing with another 360 I'm going to put in a 1989 W150. Did you list a rebuild kit that you used in any of the videos in this series? Also, in the powerwagon you mentioned, will you be rebuilding transfer case by chance? Or maybe you have and I just haven't gotten to that vid yet. GREAT FREAKING SERIES MAN!!! I may screw it up, but it won't be from any of your instructions.
@YoshimoshiGarage
2 жыл бұрын
I didn't buy a kit, I got individual parts from Cobra Transmission. I do plan on rebuilding the NP205 - though I'd like to find a spare and rebuild it while the truck is still drivable.
@steve1774
2 ай бұрын
Thank you , I'm now unstuck !!!
@arthurbach9016
5 ай бұрын
Been following your channel for a while. Having a problem rebuild my transmission 72 7 I've lost reverse The valve body attaches frount where under pump fuild the transmission. I have a stripped out bolt. Can that cause the problem?
@rboynton8671
5 ай бұрын
Interesting how you mentioned you were using parts from a B&M Transkit. The Transkit comes with their shift kit yet I did not see any mods to the rear servo, accumulator (rod) or the cupped orifice that goes into the direct clutch passage in the case. Were you going to save those parts for the other TF build you were going to do?
@YoshimoshiGarage
5 ай бұрын
Yes, I decided to save the kit parts for another build
@ihatecrackhead
Жыл бұрын
I only 3 frictions on my overdrive(A500SE-42RE) now I have 5 but I had to change both the selective shim and the apply shim
@user-oi7db5eu5v
4 ай бұрын
Hey man, I know I'm asking a lot of questions. But I'm almost done. Hopefully. Did u purposely NOT lube the roller bearing on the tail-shaft? thanks bro.
@YoshimoshiGarage
4 ай бұрын
It won't hurt to lube it, but it doesn't spin until you're in gear, so the pump will have lubricated it before you start driving it.
@user-oi7db5eu5v
4 ай бұрын
@@YoshimoshiGarage Thanks brother man.
@dingbat4596
2 жыл бұрын
You obviously have more experience with mopar transmissions than I do. Problem; I rebuilt my transmission, along the same lines as you did an A 727 that sits behind a 400 big block in a 71 plymouth duster. I have NO passing or kickdown gear. I can hand shift and 1st through 3rd are there with no slippage. I adjusted the throttle with the kickdown lever so when carb is wide open trans lever is fully depressed back. NO passing gear or kickdown. Also trans shifts through gears really fast, shifts from first to third by 35 mph. I have pulled the tail shaft and checked and cleaned the govenor, also dropped the transmission pan and pulled the valve body taking it completely apart noting where the ball bearings go. Still the same... One questio, this valve body is out of a RV transmission, would that matter? HELP!!!
@YoshimoshiGarage
2 жыл бұрын
The behavior sounds like misadjusted kickdown to me, but you say you've checked that so my next guess (and it's just a guess) is low pressure for some reason. Maybe a bad/pinched/backward seal or something? Different valve bodies will have different shift characteristics, like exactly when and how hard the shifts are, but none should have if shifting all the way to 3rd that soon.
@andrewtreloar7389
2 жыл бұрын
Hi mate, which master rebuild kit did you go with, and did you end up installing the Transgo shift kit (was it no.2 or no.3??). Great job by the way, love the video and thanks for documenting it all!
@YoshimoshiGarage
2 жыл бұрын
I actually put the kit together piecemeal from Cobra Transmission. I did put in the Transgo kit, but my computer crapped out and I lost the footage.
@lexrios5452
2 ай бұрын
Did you replace the front servo rings?
@YoshimoshiGarage
2 ай бұрын
Yes.
@lexrios5452
2 ай бұрын
@YoshimoshiGarage Ended up ordering a billet servo from CRT. But I've been following your restorations/assembly videos. Loving them! 🤘🏼
@donlittle0003
Жыл бұрын
What rebuild kit do you recommend,thanks
@YoshimoshiGarage
Жыл бұрын
I bought my parts from Cobra Transmission Parts
@brettpowter6010
2 жыл бұрын
Why run a 904 valve body in a 727
@YoshimoshiGarage
2 жыл бұрын
The separator plate from the 727 was super worn and I had a spare 904
@brettpowter6010
2 жыл бұрын
@@YoshimoshiGarage did it work ok after the vb swap cheers brett
@YoshimoshiGarage
2 жыл бұрын
@@brettpowter6010 It did. Other than the one hole, they're basically the same
@damnimcooltom1
2 жыл бұрын
I'm looking forward to seeing the boy's transmission damage.
@YoshimoshiGarage
2 жыл бұрын
It's probably going to be soon simply because it's really in the way right now.
@MrDurandal25
2 жыл бұрын
*** Always change out the shift shaft seal ****
@YoshimoshiGarage
2 жыл бұрын
Definitely good advice. I changed it, and I think I showed it somewhere in the series.
@MrDurandal25
2 жыл бұрын
@@YoshimoshiGarage Great vids. I have a 67 Coronet, and many over the years, and the 727's have always been good to me.
Пікірлер: 47