That's why I cut at a different angle every time I mow. I have some Ballard gold blades they cut very nice but my Predator blades have more lift and throws the discharge much farther.
@Doubie.
25 күн бұрын
So to clear up some misconceptions it’s not that your stock blades are making more lift it’s that there lifting more and over filling your deck for the speed your going your mid rise blades are doing better because there’s not lifting as high they stripe a little less but they cut a little longer and more evenly because you not overfilling the deck Also your not comparing 1 to o one blades in size or use case of course there going to have a wide performance gap The blades are bent up because the down pressure from the lift flexes them down
@FindersKeepers88
Ай бұрын
Good, Thx
@gordonliddy9418
Жыл бұрын
I bought some for my X-One 60" and they sure do throw the grass out further! They also do cut better than my oem blades.
I have used 3 different Hustler Super Z’s with the 60-inch VX4 deck over the past 7 years. All came with the 3-inch-wide OEM blades. I have mowed commercially since 1989 and liked these blades better than any that I have used. They cut well and run 4 to 5 times longer before sharpening is needed.
@americandream_89
Жыл бұрын
Yeah the Oem are hard to beat. I’m going to try the Ballard gold when available for comparison
@jaybrown29
Жыл бұрын
The Ballard hi rise. Has so much suction and cuts everything at full speed and we use wright zk mowers and mow around 11mph
@jaybrown29
Жыл бұрын
I find oems barely have any lift. Don’t believe me try the puddle challenge. Run your mower over a puddle at 3 inches or 4 whatever. Oem won’t suck uo any water. The Ballard hi rise will suck all the water out of that puddle
@americandream_89
Жыл бұрын
@@jaybrown29 that may be so with a Wright mower but hustler runs a much better Oem blade than most. Go back and watch the first video.
@larryweaver9784
Жыл бұрын
@@jaybrown29 What width deck on your zk's and what state are you in. I have a Wright Stander X 52 and a Wright ZXT 61. I am in Illinois.
@mrme9517
3 ай бұрын
My oem blades are horrible but the ballard blades for me aren't the best too thin i did try the x blade set up also pure trash i do have the ballard razor blades i feel copperhead blades did better for me i have a 22 bad boy maverick hd with a 27hp efi honda motor it was a horrendous experience but u may want to try their high lift or super high lift blades what type of ballard blades are u using i can say for my application ballards are overhyped and crappy honestly
@americandream_89
3 ай бұрын
Click more below video and watch the last video I’m running high lift
@kevingebert4316
Жыл бұрын
Has anyone notice a very loud rumble with the Hustler Super-Z OEM Fusion blades? I've read in some forums others had that noise also. I switched to different oregon and ballard blades and the roar went away. Wearing ear muff type hearing protection was unbearable so I went to inserted ear plugs when mowing with them. I often use the smaller skinnier blades for X-blade setup but this spring I stuck the OEMs on and wow it was almost ear piercing type of a rumble roar. blades were balanced and sharp. I've got about 60hrs on my Super Z now. I have a set of Ballard Gold to put on next. I think the hi-lift ballards cut a tad better than the razors which are a mid lift when cutting as a single blade setup. I use the razor and ripper for X-blades typically with great results after the spring growth.
@gordonliddy9418
Жыл бұрын
Oregon makes the oem blades for hustler.
@mooch91
Жыл бұрын
Honestly don't know if that matted effect you are getting with the tires is a function of the blades so much or the time of year and height you're cutting. I've found, particularly if you use the same couple of tracks to cut, that this will happen as the year goes on, regardless of the blade, particularly when cutting tall. Have never used the Ballards but have similar experience with other blades and mowers.
@americandream_89
Жыл бұрын
I think this is correct. I’m doing testing again now with both Oem and Ballard. I’m starting to think it was just that part of the year. Thanks for your input. I will make a full correction video when I get my full conclusion. However I know for sure they don’t hold up like Oem hustler blades. The gold series may be different
@mooch91
Жыл бұрын
@@americandream_89 I would like to give them a try on my Exmark Lazer. The Exmark comes with a high lift blade, and I’ve tried one that’s even higher lift, but it’s a wider and thicker blade than OEM (looks like your Hustler 3” OEM). With a 25hp machine, I found they rob too much power. The Ballard looks to be the same width and thickness as the OEM Exmark, plus gives the added lift.
@aquabomber
Жыл бұрын
Respect the honesty
@americandream_89
Жыл бұрын
Thanks. I’m going to run them again soon just to see thoughts again
@philliphall5198
Жыл бұрын
I’m waiting on a good review on them and I don’t like the thinner blades eather Was told they don’t stay sharp at all and sharpen easily but have to keep sharpening for every job Not for me
@americandream_89
Жыл бұрын
Make sure to watch my last video on these.
@Athletesperformance1
Жыл бұрын
Did miss the part where you said Ballard Ripper or Razor? Also I've never seen a oem 3" wide but I don't mess with Hustler...
@americandream_89
Жыл бұрын
All excel factory hustler blades are 3” wide. But I’ve got a video coming out. I think my problem last year end of year was great health. It didn’t have that spring summer reflex to it. Also repetitive Passes over same lines. I know the excel factory hustler blades hood up better but I’m thinking the Ballard are still a great blade. I’ve been sitting with them back and forth this year testing. Both blades cut well.
@platinumlawnservice
Жыл бұрын
Ive found that a blade is a blade. I run copperheads on my toro because theyre cheaper but almost identical in thickness and whatnot. I did run a set of knockoff blades and bent one the first time i grabbed a tree root. I think hes just putting his name on a blade made by another manufacturer anyway so. I dont have any desire to buy the ballard blades but id try some out if they were free or on deep discount. We go through too many blades and beat the crap out of them too.
@americandream_89
Жыл бұрын
Fully agree. I’ve since then retested them and I think it was my fault from going over the same lines. I made a full video explaining. I was wrong on Ballard blades 🙃 kzitem.info/news/bejne/omqZ0KybnoN_gJg
@blockchainbiker2549
Жыл бұрын
Why is that grass 5 inches long!? Doesn't even look like it was cut
@americandream_89
Жыл бұрын
I cut higher at points in the year to really define the stripes then lower after
@christinascorsone7137
Жыл бұрын
None of my Moore's if I cut grass high looks worth a darn I have an old 2750 Dixie chopper I also have a Scag tiger cat 2 fitech cut the grass tall it doesn't look worth a darn
@americandream_89
Жыл бұрын
@@christinascorsone7137 I cut at 4-4.25 and it looks great. I was wrong on Ballard blades 🙃 kzitem.info/news/bejne/omqZ0KybnoN_gJg Dixie choppers are the worst stripping mowers I’ve used. The deck is to open. Scag do well.
Пікірлер: 32