jobs coming on nicely bud and your problem solving is bang on
@NicksGarageUk
3 ай бұрын
Cheers pal,, I’m trying to show the ups and downs of it rather than just what works
@tbdogfosters
3 ай бұрын
@NicksGarageUk definitely helps out ppl who my be thinking about doing the same to see what doesn't work and what does 👍
@Stop..carry-on
3 ай бұрын
Frigging heck Brilliant work mate, Id be interested in seeing the 3d printing of the parts you need
@NicksGarageUk
3 ай бұрын
I’m not the best at designing the 3d prints but I will try and show some of the work that goes into it
@jeffcrompton5796
3 ай бұрын
clever work fella , looks like a head buster 👌
@NicksGarageUk
3 ай бұрын
It’s not so bad if your methodical 👍
@so-roadkill
3 ай бұрын
Nice 1 your doing a hell of a job man
@NicksGarageUk
3 ай бұрын
Tough at times but I’m pulling through now 👍
@xyoungyx
3 ай бұрын
good job man.here the engine mount on turbo side that i seen is upside down.the rubber-if it pops.oil will go everywhere.they are oil filled buddy.also any swaps i do involving diesel i always buy a new set because they are bad for goin due to torque.and aged obviously.getting there though
@NicksGarageUk
3 ай бұрын
I have a set of landrover v8 mounts for it ready to go on,, they are slightly shorter,, engine is coming back out to finish fabrication 👍
@petergrinnell2500
3 ай бұрын
Looking really good and the little bits like the air con looking tricky job and that w why don't u get some small gas welding rods where you can use a little propane burner on don't no it braze rods would do it just a idea that wiring looks a nightmare i could not do that my self good luck but its getting there and looking great
@NicksGarageUk
3 ай бұрын
Tried brazing it first,, unfortunately the bmw pipes are so thin and low quality they melted before the rods,, Once I got better at tig welding it wasn’t to bad and I could probably do it again in a couple of hours (plus making the fitting again)
@rstvan
3 ай бұрын
Alot of work gone into that. Looking good 👍
@NicksGarageUk
3 ай бұрын
Cheers pal,, chipping away
@SuperRon
3 ай бұрын
Great work! So much progress!
@NicksGarageUk
3 ай бұрын
Yeah,, it’s all the little bits.. I feel like I’ve done nothing 🤣
@NorthernGrowsUk
3 ай бұрын
Well done dude its some job to do on your own but sooooo looking forward to the finished job
@NicksGarageUk
3 ай бұрын
Cheers,, it’s slowly continuing along now.. just need to prove it will all work with a trial fit before I take the engine back out,, needs a fair bit of welding doing
@NorthernGrowsUk
3 ай бұрын
I've got a mk5 tipper that's been fully rebuilt and solid as a rock in blue single wheel with German axle that i drive daily and love it but it still needs a few little bits to make her mint but to find one that don't need welding is a miracle. I've had loads over the years but I'm keeping tabs on your build to do my own in winter but yours is the most informative build I can find and makes for a good watch. You don't sound too far from me in Bradford either
@NicksGarageUk
3 ай бұрын
@KGBCUSTOMAIRBRUSH I’m not so far,, just in Manchester by the trafford centre,, I’m going to fabricate my own panels this year,, a decent job but not perfect and will pull it off the road in a few years for a full rebuild
@jamesnorman2108
3 ай бұрын
Pressurise the ac with compressed air to see if the clutch works
@NicksGarageUk
3 ай бұрын
It is,, I’m not sure the pressure is enough though
Пікірлер: 23