i want to know how to clear high resistance fault in gent vigilon
@karthikeyan.s7502
4 жыл бұрын
Hi Boss, how do the floor wise programming for civil defense, ex. 4 loop Facp, 10 floor building.can you explain me.
@MdKalim708
Жыл бұрын
Can you make a complete video on programming
@royalgaming9831
9 ай бұрын
Hello sir if i want use this software which course i have to do programable logic controller?
@florendoregner
8 ай бұрын
You need to contact local distributor to assist you. If you need hep to locate local distributor or you contact me at regner220@gmail. com
@MdKalim708
9 ай бұрын
Can you make a video on gent panel networking and its programming
@florendoregner
8 ай бұрын
You need to contact local distributor to assist you. If you need hep to locate local distributor or you contact me at regner220@gmail. com
@kumalamandol2878
3 жыл бұрын
Shar your componey hab vecation or not??
@mohammed-cz9hz
3 ай бұрын
Good doing brother Please how I can solve high resistance fault in gent
@syedsulaiman2262
Күн бұрын
How to program in gent vigilon "Example: Four panels are network-connected, with one panel working as the master panel. For instance, if an alarm is activated in any building, all activities need to be reported. Then two buildings are connected, and a device is activated in one building, it should trigger simultaneous evacuation in both buildings. Then however one building is a separate entity
@MOHAMMADJAVED-jb4pk
3 жыл бұрын
From I can have software?
@MuhammadUsman-th5pq
3 жыл бұрын
Very helpful sir . Can we edit location by using panel keyboard. Thanks
@florendoregner
3 жыл бұрын
Yes
@Dime_Bar
2 жыл бұрын
@@florendoregner maybe
@giantgobblin1026
2 жыл бұрын
Yes you can...
@Dime_Bar
2 жыл бұрын
No
@manikandan5980
2 жыл бұрын
Bro can you tell me how to do network configuration like we have 12 panel in one site. we need centralised panel to monitor. Give me some idea how we can do.
@giantgobblin1026
2 жыл бұрын
you need to add one terminal node and network card on its panel
@giantgobblin1026
2 жыл бұрын
Who can answer...How to configure monitor module as fire using panel without comtools?
@florendoregner
2 жыл бұрын
Not possible.Output module single interface you can program without software, but monitor LV module is not possible. Contact me for further explanation: regner220@gmail.com
@osmanmassad8104
2 жыл бұрын
hi good morning it this software work with all gent fire alarm panel and how I will download it. can you please help me
@florendoregner
2 жыл бұрын
Contact your local supplier for support to obtain factory training in order you can get on it. For further explanation you can contact me at : regner220gmail.com
@gameforfun5539
2 жыл бұрын
sir can i take the software from you. reply asap thanks
@florendoregner
2 жыл бұрын
Contact your local supplier for support to obtain factory training in order you can get on it. For further explanation you can contact me at : regner220gmail.com
@MOHAMMADJAVED-jb4pk
3 жыл бұрын
Does it need dongle key to program?
@florendoregner
3 жыл бұрын
it is required license site key.
@alumar5723
Жыл бұрын
@@florendoregner Can you help me to program the panel
@florendoregner
Жыл бұрын
@@alumar5723contact me at regner220@gmail.com
@Traditional_Foods_Across_World
3 жыл бұрын
whrer can i download this software brother
@MOHAMMADJAVED-jb4pk
3 жыл бұрын
Hi Renger, how you can help me in panel programming
@arinzechristopher2349
3 жыл бұрын
Thanks, pls how can I get the software?
@mohdarshil3212
8 күн бұрын
Can you provide me gent panel programming software
@djboy8886
3 жыл бұрын
Hi would be aboe to provide me with the software? Love your videos and thank you
@sukualon
3 жыл бұрын
@@florendoregner hai. Please help me I need this panel software
@florendoregner
3 жыл бұрын
@@sukualon contact me
@user-jn2sq8xy7n
2 жыл бұрын
@@florendoregner ه
@florendoregner
2 жыл бұрын
Contact your local supplier for support to obtain factory training in order you can get on it. For further explanation you can contact me at : regner220gmail.com
@MdKalim708
Жыл бұрын
Hii.. can you make a more video of commisioning in details
@florendoregner
Жыл бұрын
What programming C/A do you need?
@swmltrainspotting
3 жыл бұрын
I need this software
@florendoregner
11 ай бұрын
You need to contact local distributor to assist you. If you need hep to locate local distributor or you contact me at regner220@gmail. com
@DW-ei1zr
2 жыл бұрын
Hy
@ahmedtasin7183
3 жыл бұрын
Hlw sir i need the configuration software
@syedsulaiman2262
Күн бұрын
Please make video How to program and purpose Master group Master sector link Delay block Delay block link Time slot Command builds Message routing
@DW-ei1zr
2 жыл бұрын
Bro how to find this software
@florendoregner
2 жыл бұрын
Contact your local supplier for support to obtain factory training in order you can get on it. For further explanation you can contact me at : regner220gmail.com
@InFlowAnswer
10 ай бұрын
I want this software bro
@florendoregner
8 ай бұрын
You need to contact local distributor to assist you. If you need hep to locate local distributor or you contact me at regner220@gmail. com
@arifhussainansari8175
4 жыл бұрын
Thank you so much sir for information
@florendoregner
4 жыл бұрын
sounds good to hear feedback from you
@arifhussainansari8175
4 жыл бұрын
Yed i heared you wel
@arifhussainansari8175
4 жыл бұрын
Sir can we crak the password if posible so how to crak pls explane
@arifhussainansari8175
4 жыл бұрын
Sir can you uplode video full basic training of gent vigilon compact step by step
@florendoregner
4 жыл бұрын
@@arifhussainansari8175 no,unless you know the existing password and you can change it. or else if you dont know it and the option is a daily password log in.
@CookWithAkhter
5 жыл бұрын
When i test one floor everything is working normal elevator stopped, AHU stopped,Access door open. In other floor elevator continuously working and other things working good. What will have to do please reply. Is it programming issu . Can i solve from winmag plus please give me reply
@florendoregner
5 жыл бұрын
check your program if what is the proper actions when you triggered the device in one floor, and if you want to be general actions so you need to assign the device to all output signal action during the event of fire . and you can do manually in the panel if you know it how to re-program or can you do it in gent com.tool software. There is no option to do it in winmag pc.
@CookWithAkhter
5 жыл бұрын
@@florendoregner can you tell me how to do from panel
@CookWithAkhter
5 жыл бұрын
I need your help. Please give me your e-mail id
@florendoregner
5 жыл бұрын
@@CookWithAkhter florendoregner@yahoo.com
@CookWithAkhter
5 жыл бұрын
Dear sir I hope you are doing well I am jawed akhter Fire Alarm Technician I need your help related to manual programming from panel We have gent vigilon 6 loop card panel We are using one loop card for one floor When we pressed the MCP OR any alarm cases some activity is going on. Sach as stair fan running. Elevator stopped, AHU stopped, Access door open for every one we are using s4-34420 interface module. When alarm coming in 3rd floor every thing is working good. For example AHU stopped, Stair fan running, Elevator stopped, Access door open every thing is working fine But when we pressed MCP in 2nd floor Elevator not stopped, and stair fan not runing . Please tell me how to program manually from panel
@waqas7783
4 жыл бұрын
hi boss I think you r doing great great can you please reply me with the Gent configuration software ?waiting for your urgent reply.
@florendoregner
4 жыл бұрын
thank you and contact me florendoregner@yahoo.com
@junreyintes6523
4 жыл бұрын
Sir I need the software thank you for kind sir
@achu3007
5 жыл бұрын
Can i get gent software??
@achu3007
5 жыл бұрын
Ok
@imirzaumair
4 жыл бұрын
I need software
@rukurukin4359
5 жыл бұрын
saan po kita pedeng iadd sir.
@muhammadasadimam756
5 жыл бұрын
Can you please share vedio of how State of device can be cahnged in software
@florendoregner
5 жыл бұрын
Hi,you can change the device state condition at panel itself and its very easy to do for you. But you can used software thru device config and just put the device states option on (states) and off (states) after proceed to timeblock put designated time required by your client at site if when it be the action of youe states condition to action.
@achu3007
5 жыл бұрын
Boss u have software??
@muhammadasadimam756
5 жыл бұрын
@@florendoregner But i just want to decrease sensitivity of some devices , not want to put them off.
@florendoregner
5 жыл бұрын
@@muhammadasadimam756 yes you can do by changing state only in the panel and please refer to state condition code
@jhazpervillanueva324
4 жыл бұрын
Sir san ka nag wowork pano mag apply jan same field and gents also I handle
@florendoregner
4 жыл бұрын
work at private company.
@karthikeyan.s7502
4 жыл бұрын
what is tha password of gent panel, if normal password changed by somebody,how to break?, we have 4 sites,
@florendoregner
4 жыл бұрын
required daily password from your OEM manufacturer GENT only once you dont know the password.
@joyaljoseph683
5 жыл бұрын
Hi boss
@joyaljoseph683
5 жыл бұрын
I am working gent in Kuwait
@florendoregner
5 жыл бұрын
@@joyaljoseph683pretty much good working with gent
@sulemansafeer7856
3 жыл бұрын
@@joyaljoseph683 hi i'm also Gent Commissioner in Pakistan
Пікірлер: 93