thank you so much i work night security and the alarms went off on a false call after all standard procedures where followed no one knew how to resett the alarm until i found you so thx once again
@64GreenDragon
Ай бұрын
Just wot I wanted, nice & clear instruction. But can I ask ? Do you need to go to the alarm point to set the sounders off or can this be done on the panel. Wr have exactly the same panel as this.
@ThePlungerManOfficial
4 жыл бұрын
how do you wire a kentec sigma fire panel into a Apollo alarmsense call point
@amygray5080
7 жыл бұрын
Hi Dan - Great videos! Do you have anything for Haes Surveyor Excel-k?
@DanstheEngineer
7 жыл бұрын
Amy Gray thanks I haven't anything yet but it is one on the list to do in the future
@asifiqbal1963
6 жыл бұрын
Morley zx5se FAS panel showing fault LOW OUTPUT , could you explain how to solve it
@DanstheEngineer
6 жыл бұрын
Hi Asif, is it saying what has a low output?
@mohdfaizolazua2563
2 жыл бұрын
Do you know why,after replaced smoke detector, current reading showed is normal but contamination still show -83
@zakariahoubi778
7 ай бұрын
Bonjour j'aimerais vous poser une question, comment supprimer un détecteur ou une sirène sur cet central??
@shadyem8779
2 жыл бұрын
Do you know how to silence cause its always beeping but no troubles.
@mikemakokha8931
2 жыл бұрын
Hi am trying to set but it's not extinguishing when count is up
@rebeccakearney1968
Жыл бұрын
I really hope you see this message as I am at my wits end. I've had this exact panel installed a few weeks back and from day one it's omitting a high pitched sound and a low loud hum/buzz. I can hear it throughout the house behind closed doors. There is no escaping the sound. Do they all make this sound or is something wrong. I'm having a hard time backing my own corner with the guy who installed it and my landlord said to just ignore it. Also at night I can see a red light coming from zone 4 on the panel. Any advice would be greatly appreciated
@CRL_f
11 ай бұрын
Those panels do make that sound for some reason and I've noticed that sometimes the leds just light up dimly. Hope this helps.
@Club_vibes69
2 жыл бұрын
Hi quick question, can you get 2 stage mode on sigma?
@Eltot_1031
5 жыл бұрын
Where is the standard location of manual call point.?
@DanstheEngineer
5 жыл бұрын
At ANY normal exit of the building, no more than 45m walking distance within a building, change of level within a building i.e stairs.
@chrisvidito7411
2 жыл бұрын
If I lost the reset plastic key - how can i reset these devices?
@daveedwards139
6 жыл бұрын
Hello there I have a MxPro 5 fire panel I need to isolate some detectors in a zone because of some maintenance work taking place do I need to disable outputs or inputs I know when I do a silent fire test I disable outputs for the bells or will disabling the zone be enough to stop the bells going off and Brigade being called. Many thanks
@DanstheEngineer
6 жыл бұрын
Dave Edwards hi. You need to disable the individual inputs so check what addresses of the devices you want to disable and disable them only but also I would cover them to prevent any contamination. You can disable the Zone but you want to limit how many detectors you disable and sometimes when you're disabled in the zone you're also disable in the sounders in that zone which you don't want to do. And remember you need to keep the disablement off but as little time as necessary because ultimately you don't have detection when you disable in those areas so you may also want to think about your fire precautions
@jonvars70
6 жыл бұрын
hi, a newbie here. We are currently testing the same fire alarm system used in the video. all tests goes well except that when smoke detectors were tested with smokes the LED indicator would light up but alarm won't activate. What could be the problem?
@DanstheEngineer
6 жыл бұрын
Yosef 618 before you performed the test are any led indicitators illuminated other than the green power? If not you might have a programmed disblement. Or the sounders might be incorrectly wired. Do they work at all?
@jonvars70
6 жыл бұрын
Dans the Engineer , thanks for the response. The "general fault" indicator LED is illuminated and also the 'battery fault" in the lower section because we tried it without batteries installed. Strobe lights and ringer are installed in NAC terminals while smoke detectors (with MCP) in Z1 and Z2 terminals . When the MCP is activated alarm would sound. But if individual smoke detectors are tested, alarm wont sound but the LED in the smoke detectors would light up. We are using Apollo series A65 Smoke detectors.
@DanstheEngineer
6 жыл бұрын
Yosef 618 there's no need to remove the batteries whilst testing this so reinstate them. So your sounders are not on the zones, they are dedicated alarm circuits on the alarm terminals? And when you test a smoke, does the panel fire LED indicator illuminate?
@jonvars70
6 жыл бұрын
Dans the Engineer. Fire LED in the panel did not illuminate, only the LED of the smoke detector...the smoke detectors we have do not come with sounders, should it have sounders along z1 and z2? If so, will it trigger alarm in the panel?
@DanstheEngineer
6 жыл бұрын
Yosef 618 no you do not need to have sounders on the zones. There are 3 variants of the panel in the video. 1. Standard conventional also known as 4 wire. 2. AlarmSense and 3. SavWire. Mine is a SavWire where sounders can go on the zones but also as separate alarm circuits. If your call points set off the sounders it tells me the panel is functioning how it should so either the smokes are not connected correctly or they are disabled. It is possible to make programmed disablements. Open the front door and it lists what programming can be done. Do you have any spare zones because you could try by swapping the affected zones with a spare zone to see what happens
@kashifali92
3 жыл бұрын
hello, please tell me what is ADC Supply Fault
@SunSecurity
6 жыл бұрын
What does KAC actually stand for? I have always wondered this.
@DanstheEngineer
6 жыл бұрын
Random Ytuber I don't have a clue. It doesn't say on their website either www.kac.co.uk/call-points.html
@SunSecurity
6 жыл бұрын
Ah, Ok, thx anyway
@gordonferguson3781
5 жыл бұрын
@@DanstheEngineer Kidderminster Alarm Company = KAC
@marjosephedjan8734
5 жыл бұрын
Trying to test the smoke detector, the LED indicator in the smoke detector is activated, but the panel does not detect it and no sounder is activated. Hope you can help me. Thanks, mate.
@DanstheEngineer
5 жыл бұрын
Sounds like the detector isn't connected correctly. If it has power (which clearly it does), it'll light up in fire condition but won't tell the panel. What detector is it and what protocol is it? Alarmsense, 2wire or 4wire?
@marjosephedjan8734
5 жыл бұрын
@@DanstheEngineer I'm using kentec sigma a-cp 8 zone conventional fire panel, and my detector is series 65 optical smoke sensor detector standard.
@DanstheEngineer
5 жыл бұрын
@@marjosephedjan8734 check how it is connected. Are the other detectors on the zone creating a fire signal when active?
@jasonrich4664
5 жыл бұрын
Zones mean loop? Great video mate
@andrewcarolan7315
5 жыл бұрын
No mate, loop are addressable panels. This is a conventional panel, so zones means circuits. Single run for each zone with EOL resistor.
@thabangchesane9643
3 жыл бұрын
My system is showing a fault on the sounder and general system, what should I do to reset the panel?
@DanstheEngineer
3 жыл бұрын
I highly recommend a fire alarm engineer attends to look at the fault. You won't be able to reset the panel without rectifying the fault.
@thabangchesane9643
3 жыл бұрын
Thank you
@georgecollins2412
6 жыл бұрын
Why did you use seven nation army as the background music
@DanstheEngineer
6 жыл бұрын
George Collins because it is a brilliant song! It's actually a cover that I've used. A link to the music is in the descriptions
@laplace9818
4 жыл бұрын
How to enable control mode access please
@atravelwithpaws2606
6 жыл бұрын
What to do, when buzzer is disabled
@DanstheEngineer
6 жыл бұрын
It needs to be enabled. You need to know when the panel is indicating an fault or fire (sounders may be faulty or disabled) otherwise you may not know. It is a basic engineer function but I am afraid that I am not going to provide any engineer functions as a panel can really be altered with by someone who isn't trained. By all means - contact Kentec!
@striketeam316
3 жыл бұрын
Do you know by any chance why this model of panel would be having an intermittent power fault / general fault? The internal buzzer will sound on the box,then the fault will clear for a few moments,then start up again. It will go on like that for a few hours. Then stop completeley for a few hours,and then start again?
@DanstheEngineer
3 жыл бұрын
A power fault can be a number of things. Either the battery, power supply unit or mains supply is faulty. It would be unlikely for the mains to cut out without anyone resetting unless there's a loose connection. The batteries could be loose or near end of life or the PSU could be playing up. It needs an engineer to attend to look through these things systematically and provide a solution. My instinct based on what you've said is it sounds like something is loose but I cannot stress how much an engineer and only an engineer needs to look at this.
@helyrobertorojas7058
3 жыл бұрын
I need the wiring diagram please
@alaahasany4495
Жыл бұрын
thanks
@caramelthecat3128
6 жыл бұрын
The intro scared the hell out of me
@nourddinemoutawakel9018
4 жыл бұрын
Je veux les explications en arabe ou français svp.
@faycalmez7330
3 жыл бұрын
I have a problem with this alarm, I have sent you a message in messenger
@atravelwithpaws2606
6 жыл бұрын
Please help
@gregbouchard8353
5 жыл бұрын
How are u ok mate are u hove a good day mate u are u ok mate u are u hove a good day mate form Greg bouchard hove a good day mate am a big fan of u mate well done
@ThePlungerManOfficial
4 жыл бұрын
and smoke detector
@gregbouchard7935
7 жыл бұрын
See good Mate you or u ok Mate cone we Tok Mate at we’ll be good Mate ok
Пікірлер: 58