Sir can you add lcd screen indicate fire and smoke percentage
@yelbelpoys5276
2 жыл бұрын
for the arduino uno code and for the gsm module code is it the same or different code? because there should be two seperate codes each, for arduino uno and for the gsm module
@ecit
2 жыл бұрын
You need to upload code in Arduino only.
@thinksides
3 жыл бұрын
Really Helpful and perfect explanation 👍
@ecit
3 жыл бұрын
Thanks 😊
@bharathhkrishna
2 жыл бұрын
Great presentation sir👌👌 Can I use MQ3 instead of this and if yes what's the modification I've to make in the code And I won't be using led so can I do this without using the resistor?
@ecit
2 жыл бұрын
Yes, you can use MQ3, if it has analog output. You can use this code without change. If you are not using LED, then you don't need to connect resistor too
@bharathhkrishna
2 жыл бұрын
@@ecit oh superb Thank you sir
@bharathhkrishna
2 жыл бұрын
Sir can I give a 9V supply to the gsm Or is it supposed to be 12V The network in the gsm goes off after the first 5 secs Is it because of the supply? The code we've given is exactly the same
@ecit
2 жыл бұрын
@@bharathhkrishna GSM module works on 9V, however can you share the link of your product? Or read about power supply in datasheet or product description
@gennicabergado2904
5 ай бұрын
Hi sir can i use SIM 800L instead of SIM900?
@ecit
5 ай бұрын
Yes, you can use SIM 800L also.
@josephusufunzuza1665
Жыл бұрын
Thank you can I use the A9G GSM module in place of the SIM900 if so what's the modification on the code.
@ecit
Жыл бұрын
I have not used the A9G, but I think there will change in library and may be in AT command. You can use remaining logic from this code.
@festushyginus3826
2 жыл бұрын
Sir can I use a flame sensor instead of mq135 and can I add more that one phone numbers to the code. And also sir can it be simulated on Proteus. Need it for school project
@ecit
2 жыл бұрын
Yes you can use analog pin of flame Sensor, For adding multiple numbers you need to change the code, you can refer the description link for example code, I am not sure about proteus simulation, however it should be possible.
@festushyginus3826
2 жыл бұрын
@@ecit Thank you sir
@itswaniler6784
Жыл бұрын
Sir pls help me..i having a trouble where i cant get the signal , the gsm were blinking too fast mean that there we no signal reached right?wht should i do to fix this problem
@ecit
Жыл бұрын
First make sure that your connection is ok. (GSM) Tx --> Rx (Arduino) (GSM) Rx --> Tx (Arduino)
@maureenanne1675
3 жыл бұрын
Can i used Mq2 sensor instead of mq135? Does the code also will be different? And which part of the code should i change? Hope u cna answer me. Thank you
@ecit
3 жыл бұрын
It will work but you may need to calibrate MQ-2 for accurate result, just connect analog pin of mq2 to analog pin of Arduino
@maureenanne1675
3 жыл бұрын
I already tried it. The buzzer did produce sound once it detect the smoke. But I didnt receive the call & message. Fyi, I didnt change your coding for the calling & messaging part. So do u know why is it like that?
@ecit
3 жыл бұрын
@@maureenanne1675 check your Tx Rx pin, Connect Tx pin of Arduino to Rx pin of sim900 and Rx pin of Arduino to Tx pin of sim900 Make sure you have inserted sim card properly. You can write AT command in serial monitor to check your sim900 is working or not, or simply call to the number that you have inserted into sim900 For buzzer, it will depend upon threshold that you have set in coding
@maureenanne1675
3 жыл бұрын
@@ecit Thank you for yr respond
@manishkumargupta9962
2 жыл бұрын
4g sim use kar sakte hai ky ..gsm m ..and if sim card phone m nhi hoga then messege kis application pr receive honge
@ecit
2 жыл бұрын
With SIM900 or SIM800 you can not use 4G SIM, you can go for SIM7600 or other 4G module. If you are not inserting SIM then you will not receive any message.
@ReazulIslamGUB
15 сағат бұрын
Which gas you spray on sensor
@ecit
5 сағат бұрын
@@ReazulIslamGUB Sanitizer has major element as alcohol and chlorine
@chandankumar.u4548
2 жыл бұрын
Sir, can I use MQ6 sensor if I am doing the same project for lpg leakage detection ? Or should I do any changes in the circuit or code if I use MQ6 sensor ? Thanks!
@ecit
2 жыл бұрын
You can use MQ-6 with same code, you may need to change threshold value, otherwise everything will be same. Don't forget to subscribe this channel to get more videos on time.
@chandankumar.u4548
2 жыл бұрын
@@ecit thank you very much sir, very helpful!
@ecit
2 жыл бұрын
@@chandankumar.u4548 Most Welcome 👍
@hrithikchowdhary9722
2 жыл бұрын
Sir were we r supposed to connect the power jack??
@ecit
2 жыл бұрын
To GSM module
@hrithikchowdhary9722
2 жыл бұрын
@@ecit Sir do u have a link to make a simulation for this project???
@ecit
2 жыл бұрын
@@hrithikchowdhary9722 No
@mohammedsadiqahmad2886
2 жыл бұрын
sir, this my graduation project , please dont work gsm module anything sms or calling by the way i connect Rx (GSM) into (pin7) and Tx (GSM) into( pin8) is this correct?
@ecit
2 жыл бұрын
If you are using my code then, connect Rx (GSM) to Pin8 and Tx (GSM) to Pin7. SoftwareSerial mysim(7,8);
@mohammedsadiqahmad2886
2 жыл бұрын
@@ecit thank you sir, it's working now , 🙏🏻
@ecit
2 жыл бұрын
@@mohammedsadiqahmad2886 Good! 👍
@Maryyyy22222
6 ай бұрын
Im using MQ2 sir it can detect gas but not with smoke i set the threshold in 250
@ecit
6 ай бұрын
Have you adjust the sensitivity of MQ2 sensor?
@Maryyyy22222
6 ай бұрын
Yes sir
@wen2xvlogs577
2 жыл бұрын
Mq135 can detect smoke too? And just like fire?
@ecit
2 жыл бұрын
It should detect smoke too.
@wen2xvlogs577
2 жыл бұрын
@@ecit so this system can also detect smoke?
@ecit
2 жыл бұрын
@@wen2xvlogs577 yes, but you need to change the threshold value in the code.
@wen2xvlogs577
2 жыл бұрын
@@ecit how sir do you have another tutorial that can detect smoke too? THANK YOU for responding
@ecit
2 жыл бұрын
@@wen2xvlogs577 kzitem.info/news/bejne/tHmO2pmXjoh6dqw This may be helpful
@nehajain1787
2 жыл бұрын
Sir , Why you have not connected the power supply of aurduino?
@ecit
2 жыл бұрын
I have provided power supply to all components, watch video carefully
@jeffreyguadamor4711
2 жыл бұрын
They gathered 12 volts supply came from the supply and distributed to the arduino.
@sirjosh958
Жыл бұрын
Eng. Good afternoon. please I am doing a fire detection and alarm system using Arduino, please help me with all the equipment you will need to develop the project. Besides, I wanted to include fire detection, alcohol detection smoke detection, sms alert, call alert, and alarm .
@ecit
Жыл бұрын
In my github I have included few of your requirements, you can add other sensor in same way as I added the current one
@manitrachh
3 жыл бұрын
sir have you used 4g sim or 2g sim as call is not going so what can i do plz reply me
@ecit
3 жыл бұрын
I have used 4G SIM, but it support both the 2G and 4G SIM, Make sure you have connected TX (GSM) to RX(PIN -8) and RX (GSM) to TX (PIN -7) between Arduino and SIM900a, as well as also make sure that you have inserted SIM correctly.
@manitrachh
3 жыл бұрын
@@ecit thank you sir
@rahulnag4185
2 жыл бұрын
hello sir, what should be the changes in the connection and in the program if it is a GSM800A
@ecit
2 жыл бұрын
I think both are compatible, you don't need to change anything, however you may refer the GSM800A datasheet for its AT Command
@rahulnag4185
2 жыл бұрын
@@ecit sir how can I change it..... And can u pls help me out with that because I have my project to be shown tommorw
@ecit
2 жыл бұрын
@@rahulnag4185 instead of SIM900 use SIM800 Tx and Rx and connect it to Arduino pin, everything will remain same as shown in video
@rahulnag4185
2 жыл бұрын
No sir it's not working 😭
@ecit
2 жыл бұрын
@@rahulnag4185 what is the issue? Can you tell me what kind of message are you getting on serial Monitor?
@marcallenrubin1208
2 жыл бұрын
Good day Sir! I have used SIM800L for this project. The sensor and alarm was perfectly working but the GSM doesn't send me any message or call. I also tried to input other mobile number but ends up with the same result. What should I do? Thank you!
@ecit
2 жыл бұрын
1. Check your connection GSM (Tx) to Arduino (Rx) GSM (Rx) to Arduino (Tx) 2. Make sure that you have 2G network and 2G SIM card in GSM 3. Once you enter the SIM in GSM after power up, try to call the number that you have entered in GSM module, if it is ringing then it is okay
@azizurahimi7
2 жыл бұрын
Same situation here . But I use sim900.hm
@ecit
2 жыл бұрын
@@azizurahimi7 make sure you connect Tx to Rx and Rx to Tx Also make sure that your SIM support 2G and you have 2G network in your area
@azizurahimi7
2 жыл бұрын
@@ecit sir. Can u teach me how to connect tx n rx for GSM 900.. coz my GSM 900.. tx n rx like looping with sw
@ecit
2 жыл бұрын
@@azizurahimi7 If you are using my code then, connect Rx (GSM) to Pin8 and Tx (GSM) to Pin7 of Arduino. SoftwareSerial mysim(7,8);
@Tamilselvan-xu8sy
9 ай бұрын
How we provide power to the project
@ecit
9 ай бұрын
GSM module with 5V adaptor and use USB to power the Arduino board with 5 to 9V
@Tamilselvan-xu8sy
9 ай бұрын
thanks
@sarvadnyaambare.9716
2 жыл бұрын
Hi sir Sir can we use flame sensor at place of mq 135 Please reply me
@ecit
2 жыл бұрын
Do you have analog sensor? If yes then you can use with this code. If you have digital sensor then you need make changes in the code. Don't forget to subscribe this channel to get more videos.
@sarvadnyaambare.9716
2 жыл бұрын
@@ecit Thanks sir I am already following your channel And also sir I have one more doubt can I ask you
@ecit
2 жыл бұрын
@@sarvadnyaambare.9716 yes, you can ask me.
@sarvadnyaambare.9716
2 жыл бұрын
@@ecit Sir in this project after installing of codeing in Arduino can we need to connect Arduino with laptop for every working time Where we connect our main supply to our this project smi900a or Arduino
@ecit
2 жыл бұрын
@@sarvadnyaambare.9716 no need to connect with laptop after uploading code, you can use mobile phone adaptor to provide power supply to Arduino. For SIM module you can use 5V or 9 V (Depends upon module) DC power adaptor.
@بلالقافهياملقوف
2 жыл бұрын
If i use sim 800C does it work?
@ecit
2 жыл бұрын
Yes it will work, make sure you have 2G SIM and 2G Network
@بلالقافهياملقوف
2 жыл бұрын
@@ecit thanks❤️❤️
@SonammSingh
2 жыл бұрын
Sir can you please explain how we can make this project using bluetooth connectivity
@ecit
2 жыл бұрын
Use HC05 or use ESP32, instead of sms and call, with Bluetooth you can send notification to mobile application, you may use nRFconnect app for testing
@SonammSingh
2 жыл бұрын
@@ecit Do we need to be around then only we can get notification??
@ecit
2 жыл бұрын
@@SonammSingh yes with Bluetooth you need to be around the device. If you want to access it remotely then go for WiFi and you may use ESP8266 or ESP32 for this.
@SonammSingh
2 жыл бұрын
@@ecit And can you please tell one more thing how we can make it more advance like what more technology can we add or something like that basically I'm asking because this question is asked in interview so much
@ecit
2 жыл бұрын
@@SonammSingh You can make it as IoT project with WiFi. Collect data from sensor and send it to webpage or some server. You can watch my video with ESP8266, Part 1: kzitem.info/news/bejne/zJqOsWeXe35plHo Part 2 is also available in playlist
@yusufcemiloglu8315
2 жыл бұрын
Does it work with any gsm sim900a module ?
@ecit
2 жыл бұрын
Yes, it will work
@yusufcemiloglu8315
2 жыл бұрын
Sir this is my graduation project. All I have to do is paste the code into the arduino and enter my number and run it. Is there anything else
@ecit
2 жыл бұрын
I think you should go through code and learn from it and make changes whatever you want to make it.
@meowwngi
2 жыл бұрын
@@ecit sir I have doubt We need to insert sim card to gsm and that sim card (inserted card) has 10 digit number and our phone which we will receive alert message will have another sim card and it's own 10 digit number. So now which number should I need to upload in code??
@ecit
2 жыл бұрын
@@meowwngi number on which you want to receive SMS or call
@meowwngi
2 жыл бұрын
@@ecit thank you so much sir 👍
@jeffreyguadamor4711
2 жыл бұрын
Sir can i copy paste the program code to make my project like this working, and then also can i indicate the mobile number i insert on the gsm?
@ecit
2 жыл бұрын
Yes, you can copy paste the code and enter mobile number in the code on which you want to receive alert. (Not inserted in GSM)
@jeffreyguadamor4711
2 жыл бұрын
Ok thanks master hehe.. New subscriber here from philippines more power to your channel. May god bless you more
@ecit
2 жыл бұрын
@@jeffreyguadamor4711 Thank You!
@jeffreyguadamor4711
2 жыл бұрын
Master is it ok if i upload an inpit first the code program in audrino even if i did not connect the gsm and the wiring and other component together?
@ecit
2 жыл бұрын
@@jeffreyguadamor4711 yes, you can upload code to Arduino without connecting other components.
@monika_511
2 жыл бұрын
Hello sir ever process is working and sim in gsm is also ringing but call is not coming sir what may be the mistake
@ecit
2 жыл бұрын
Okay, verify the mobile number with correct format, you need to enter country code also. Can you share the serial terminal message of your testing?
@TorreJosephClete
9 ай бұрын
Can i do this with gsm module sim900a mini?
@ecit
9 ай бұрын
Yes you can, only make sure that you are using 2G SIM with the module, as GSM is only support 2G.
@cyberenthusiast
3 жыл бұрын
Hello hiren my gsm 900 a module is neither making any call nor sending sms after uploading the code what shall I do?
@ecit
3 жыл бұрын
Make sure your hardware connection is okay. Arduino (Tx) to GSM (Rx) Arduino (Rx) to GSM (Tx) and GNDs Also, make sure sim card in the network area
@cyberenthusiast
3 жыл бұрын
@@ecit shall I change code from mysim 7,8 to rx tx
@ecit
3 жыл бұрын
@@cyberenthusiast In that case Rx is 7 (Arduino) connect to Tx of GSM And 8 to RX of GSM
@cyberenthusiast
3 жыл бұрын
@@ecit I think my gsm 900 a module is gone... Can you suggest some link for purchase?
@ecit
3 жыл бұрын
@@cyberenthusiast if it is new then you should try to troubleshoot an issue. I don't know your location. You may order from Amazon.
@vijayvj8073
3 жыл бұрын
Sir...what i do...i will use 3 sensor. How can i change your code according to my inputs.plz reply
@ecit
3 жыл бұрын
Which 3 sensors? First we have to see, sensors are analog or digital, so as per sensors type we can change the code.
@vijayvj8073
3 жыл бұрын
Sir thanks for ur reply.. I use the 3 digital output sensor..thats not matter but the problem is how can i arrange the codes..
@ecit
3 жыл бұрын
@@vijayvj8073to use digital sensors, first define pin for sensor: example, int sensor1 = 3; void setup () { pinMode (sensor1,INPUT); //define sensor as input to Arduino as you want to read the sensor } void loop () { digitalRead (sensor1); // this will read the value of sensor } Now use your logic and complete your code Do same thing for other two sensor with pin 5 and 6
@vijayvj8073
3 жыл бұрын
Sir...tq u so much for ur valuable comment
@ecit
3 жыл бұрын
@@vijayvj8073 just try by yourself, if you are unable do the coding, feel free to contact me 😊
@jimmyelectronics2264
2 жыл бұрын
Sir can I use pir sensor instead of smoke detector
@ecit
2 жыл бұрын
Yes, you can use but you need to change the code, because MQ135 is analog sensor while PIR sensor is digital sensor. You can watch this video to lean about how to use PIR sensor then merge the code with GSM code kzitem.info/news/bejne/p2uw1XtvgoGLgXo
@jimmyelectronics2264
2 жыл бұрын
Thank you sir
@ecit
2 жыл бұрын
@@jimmyelectronics2264 most welcome, don't forget to subscribe this channel to get more videos on time.
@shanmukhsrinivas7753
2 жыл бұрын
Sir can we use Gsm 800a sim for this project
@ecit
2 жыл бұрын
Yes, you can use sim800 also. In case if you have any difficulty then refer datasheet of your module
@rahulnag4185
2 жыл бұрын
@@ecit hello sir, what should be the changes in the connection and in the program if it is a GSM800A
@shriabinaya123
9 ай бұрын
i did this project but it does not provide the message to my phone can you tell what fault might have done in this project
@ecit
9 ай бұрын
First make sure that your GSM is working, call on SIM number that you in GSM module and see if ringing, make sure that you are using 2G SIM card in GSM module. Also you can verify it by sending AT command on serial monitor
@Tamilselvan-xu8sy
9 ай бұрын
Can we use 4g sim in gsm module
@Tamilselvan-xu8sy
9 ай бұрын
Or we can use 3g sim sim atleast
@ecit
9 ай бұрын
@@Tamilselvan-xu8sy No
@ecit
9 ай бұрын
@@Tamilselvan-xu8sy yes, 3G may support 2G also
@menkamehta7339
2 жыл бұрын
Sir can I remove led buzzer or transistor
@ecit
2 жыл бұрын
Yes, no issues
@menkamehta7339
2 жыл бұрын
Thanks sir
@juliusvirgelyadao7967
3 жыл бұрын
Can it be used as motion sensor?
@ecit
3 жыл бұрын
MQ135? No
@Aakali121
Жыл бұрын
Is it possible to send the fault location in sms
@ecit
Жыл бұрын
Yes, if you have location tracking circuit with sim800 or sim900 then you can send the location also
@Aakali121
Жыл бұрын
@@ecit I mean the detector details displayed in pannel need to get in sms .
@ecit
Жыл бұрын
@@Aakali121 that is also possible, you can send any string in SMS, if you have lat long data then convert then into string and then send it through sms
@batchuchaitanyakumar2680
3 жыл бұрын
Can we use fire sensor also
@ecit
3 жыл бұрын
Yes you can use, it will detect fire also
@monika_511
2 жыл бұрын
The module is working but the LED light is not working, what might be a mistake sir
@ecit
2 жыл бұрын
Verify LED pin in the code, also verify the anode and cathode of LED, and make sure that your LED is not Faulty.
@Jaya.M78
2 жыл бұрын
Very well explained bro... Can I use MQ2 sensor instead of MQ135? Also is it fine if I use a 9V DC supply instead of 12V? Please let me know
@ecit
2 жыл бұрын
Yes you can use MQ2 analog pin instead of MQ135. Regarding power supply, read the user manual or datasheet of your component.
@Jaya.M78
2 жыл бұрын
@@ecit Thank you!
@davelodia9157
3 жыл бұрын
Sir can you add lcd screen to see alert smoke percentage smoke high and low flame
@ecit
3 жыл бұрын
Ok, you can watch my previous video about air quality monitoring system, where I have interfaced the LCD, first try by yourself, if you have any difficulties, I will help you
@rheicistmann
Жыл бұрын
hello. I have a problem. everytime I use it, the sms keeps spamming once it detects a fire. idk how to set it to send just once. please help me
@ecit
Жыл бұрын
You need to add logic for it. Initialize one variable count = 0 in void setup Then in void loop add condition, If (count == 0) { Including logic of sending sms count++; }
@rheicistmann
Жыл бұрын
@@ecit can I use boolean function on it? because although I used it, it keeps spamming sms
@rheicistmann
Жыл бұрын
@@ecit can you give me sample code? so that I could understand better. it seems lacking
@ecit
Жыл бұрын
#include SoftwareSerial mysim(7,8); // connect gsm modem on this pin String smstext; int buz = 9; //buzzer connected to pin 9 int led = 4; //led connected to pin 4 unsigned int count = 0; const int aqsensor = A1; //output of mq135 connected to A1 pin of Arduino int threshold = 250; //Threshold level for Air Quality void setup() { Serial.begin(9600); mysim.begin(9600); Serial.println("System is Initializing.."); pinMode (buz,OUTPUT); // buzzer is connected as Output from Arduino pinMode (led,OUTPUT); // led is connected as output from Arduino pinMode (aqsensor,INPUT); // MQ135 is connected as INPUT to arduino digitalWrite(buz, LOW); digitalWrite(led, LOW); delay(5000); // wait for 5 seconds } void loop() { int ppm = analogRead(aqsensor); //read MQ135 analog outputs at A1 and store it in ppm Serial.println(ppm); //print value of ppm in serial monitor if (ppm > threshold) // check is ppm is greater than threshold or not { smstext = " Fire Detected..!"; if ( count == 0 ) { sendSMS(smstext); count++; } Serial.println(smstext); digitalWrite(buz,HIGH); //Turn ON Buzzer digitalWrite(led,HIGH); //Turn ON LED delay(5000); mysim.println("ATD+YYxxxxxxxxxx;"); // change ZZ with country code and xxxxxxxxxxx with phone number to dial updateSerial(); Serial.println("Calling "); delay(50000); // wait for 50 seconds... mysim.println("ATH"); //hang up updateSerial(); Serial.println("Hangup Call"); } else { digitalWrite(led,LOW); //jump here if ppm is not greater than threshold and turn off LED digitalWrite(buz,LOW); //Turn off Buzzer Serial.println("No Fire detected"); } delay (500); } void sendSMS(String message) { mysim.print("AT+CMGF=1 "); // AT command to send SMS message updateSerial(); delay(1000); mysim.println("AT + CMGS = \"+YYxxxxxxxxxx\""); // recipient's mobile number, in international format updateSerial(); delay(1000); mysim.println(message); // message to send updateSerial(); delay(1000); mysim.println((char)26); // End AT command with a ^Z, ASCII code 26 updateSerial(); delay(1000); mysim.println(); delay(100); // give module time to send SMS } void updateSerial() { delay(500); while (Serial.available()) { mysim.write(Serial.read());//Forward what Serial received to Software Serial Port } while(mysim.available()) { Serial.write(mysim.read());//Forward what Software Serial received to Serial Port } }
@ecit
Жыл бұрын
compare with your code and add count logic in your code, If you want to send sms more than 1 then set if (count == (number of time you want sent message - 1))
@niharikarenjerla1437
2 жыл бұрын
'sendSMS' was not declared in this scope Sir, I am getting this error Please help me solve this error
@ecit
2 жыл бұрын
Copy paste your code here
@kennethpotenciano3205
6 ай бұрын
how to convert it to smoke instead of gas and fire??
@ecit
6 ай бұрын
You can use MQ2 sensor or just change threshold as per smoke value
@Vimalvs18
7 ай бұрын
Can u give me code for gas and fire detection with buzzer with call facilities
@ecit
7 ай бұрын
Code link is already mentioned in the description
@Vimalvs18
6 ай бұрын
@@ecit sir for flame sensor adding with mq2 sensor with multiple call facilities can u give the code for that plzz
@ecit
6 ай бұрын
@@Vimalvs18 you can try it by adding ATD command one after another one.
@DEEPAKYADAV-hb8nl
2 жыл бұрын
Sir can u please help me , my GSM module does not seem to respond,I am using GSM800L. Can u Please help me sir🙏🙏
@ecit
2 жыл бұрын
Tell me your Tx, Rx connection
@DEEPAKYADAV-hb8nl
2 жыл бұрын
@@ecit sir I am using GSM800L instead of SIM900A and I have given TX at 8 and RX at 7 digital outputs. And the sim that I am using is 4G for the GSM module and it is working on GSM technology.
@ecit
2 жыл бұрын
@@DEEPAKYADAV-hb8nl If you are using my code then, connect Rx (GSM) to Pin8 and Tx (GSM) to Pin7. SoftwareSerial mysim(7,8);
@DEEPAKYADAV-hb8nl
2 жыл бұрын
I'll would try that sir and share my reviews sir 🙏
@DEEPAKYADAV-hb8nl
2 жыл бұрын
@@ecit sir I have tried it several of times but it does not seem to work with gsm800l
@Maryyyy22222
6 ай бұрын
sir how to fix these problem? Arduino is connected to my laptop and it’s turning on but it says Com6 not connected i can’t upload my code My gsm module also sir is not turning on tho i already tested it call and sending sms are working but now it doesn’t even power i used Sim800l V2 EVB I used 9V battery for power supplye
@Maryyyy22222
6 ай бұрын
I connected my 5V pin of Arduino to positive rail and GND for negative rail
@Maryyyy22222
6 ай бұрын
5V pin of gsm module is directly connected to positive of battery and gnd for negative
@Maryyyy22222
6 ай бұрын
Does my gsm and arduino are got damage?
@ecit
6 ай бұрын
While uploading the code don't connect Tx Rx pin of Arduino. Just remove GSM connection from Arduino and then upload the code.
@Maryyyy22222
6 ай бұрын
@@ecitwe already disconnected it sir but still not connected on com6 tho our arduino was on through connected it on laptop
@trailerjosh7331
7 ай бұрын
can I use jio sim in gsm sim900a
@ecit
7 ай бұрын
No, JIO is 4G SIM, you need to use 2G SIM
@mrchongloi9700
2 жыл бұрын
Sir how do I add these sensors, IR sensor, smoke sensor and temperature sensor together??
@ecit
2 жыл бұрын
Use different GPIO pin for each sensors, and change the code as per connected sensors
@mrchongloi9700
2 жыл бұрын
@@ecit sir can you help me write a program?
@ecit
2 жыл бұрын
@@mrchongloi9700 yes, first write your code and let know where you want ky help
@wen2xvlogs577
2 жыл бұрын
What language do you use sir?
@ecit
2 жыл бұрын
Arduino C++
@wen2xvlogs577
2 жыл бұрын
@@ecit Thank you
@yusufcemiloglu8315
2 жыл бұрын
Can i use mq2 sensor instead of mq135
@ecit
2 жыл бұрын
Yes, you can
@menkamehta7339
2 жыл бұрын
Sir if we use gsm sim 800l then sir about power supply🤔🤔
@ecit
2 жыл бұрын
It will be same as SIM900, 9V
@menkamehta7339
2 жыл бұрын
Sir but where to give power supply
@ecit
2 жыл бұрын
@@menkamehta7339 GSM or Arduino? GSM module has external power adaptor And Arduino can be powered from USB
@menkamehta7339
2 жыл бұрын
But sir gsm sim 800l didn't have any external power socker
@ecit
2 жыл бұрын
@@menkamehta7339 can you share the link of your board?
@68-snehatondare36
5 ай бұрын
Totol cost of this project ??
@ecit
5 ай бұрын
Hardware cost can be between Rs. 1000 to Rs. 1500
@yusufcemiloglu8315
2 жыл бұрын
Sir I've been dealing with sending messages from the gsm module for a month, I can't. It does not send messages to the number I want. Can you help me please this project is my graduation project. Sir ,could you please connect to my computer and check?
@ecit
2 жыл бұрын
Okay, contact me at hirentailor.rf@gmail.com
@yusufcemiloglu8315
2 жыл бұрын
@@ecit sir i sent mail to you
@ecit
2 жыл бұрын
@@yusufcemiloglu8315 I have not received any email
@yusufcemiloglu8315
2 жыл бұрын
@@ecit sir i was sent again if you has not reach, if i write the my phone number can we communicate from whatsapp
@ecit
2 жыл бұрын
@@yusufcemiloglu8315 received your email, I will join you on TeamViewer Monday
@Parthsharma-bf3rf
2 жыл бұрын
Sir pls provide us details about how to connect it with bread board pls it's important sir pls can u provide us details it's urgent
@ecit
2 жыл бұрын
You need to connect Tx to Rx and Rx to Tx for GSM and Arduino For remaining connection you can watch my other videos
@pranavnagvekar636
2 жыл бұрын
does it supports 4g airtel card
@ecit
2 жыл бұрын
It should work! It will depend upon 2G network at your location.
@pranavnagvekar636
2 жыл бұрын
@@ecit looks like it doesn't, the network led in the gsm module blinks very fast
@ecit
2 жыл бұрын
@@pranavnagvekar636 okay, try this, once you enter the sim card in GSM module and power up system. After some time, call from your mobile to the number that you have entered in GSM. Verify - Are you getting ring on your mobile phone? I have also used Airtel SIM card in video
@pranavnagvekar636
2 жыл бұрын
@@ecit it is working
@ecit
2 жыл бұрын
@@pranavnagvekar636 okay, then now verify the connection and code. Verify Tx Rx connection
@padmamanjupadmamanjupadmam4002
2 жыл бұрын
All process is working good but call is not getting sir
@ecit
2 жыл бұрын
Verify your connection, make sure that Tx is connected to Rx and Rx is connected to Tx between Arduino and GSM module, Also make sure that you have 2G network
@padmamanjupadmamanjupadmam4002
2 жыл бұрын
@@ecit connection is correct sir but I don't y this is not working sir
@ecit
2 жыл бұрын
@@padmamanjupadmamanjupadmam4002 call on the number that you have in GSM module. If you able to hear ringing in your phone that means GSM is working and there is some issue in connection
@padmamanjupadmamanjupadmam4002
2 жыл бұрын
@@ecit ok sir I will try .. tqq a lot sir
@padmamanjupadmamanjupadmam4002
2 жыл бұрын
Sir project is working sir tq so much
@worldofprogramming7301
2 жыл бұрын
Please sir am only receiving a call from the gsm 800l model no message help me sir
@ecit
2 жыл бұрын
For SMS you need to enter your number in sendSMS function just below the void loop() function.
@worldofprogramming7301
2 жыл бұрын
@@ecit sendSMS(smstext);
@worldofprogramming7301
2 жыл бұрын
Should I replace the smstext with my number ? sendSMS(smstext);
@ecit
2 жыл бұрын
@@worldofprogramming7301 No, in your code find this line mysim.println("AT + CMGS = \"+YYxxxxxxxxxx\""); Here instead of +YYxxxxxxxxxx write your mobile number with country code
@worldofprogramming7301
2 жыл бұрын
@@ecit yes I have done that already
@jamesmartial
2 жыл бұрын
How can i get project code
@ecit
2 жыл бұрын
I have mentioned the link in description
@yusufcemiloglu8315
2 жыл бұрын
Sir How can i send image of the fire as sms or email ?
@ecit
2 жыл бұрын
Don't know how to do it with SMS and Email. But you can use ESP32CAM to capture an image and then send it via WiFi or BLE.
@vladisenergy8515
3 жыл бұрын
how to add a gas and flame sensor to a sketch?
@ecit
3 жыл бұрын
Connect you other sensors to analog pin and then read those analog pins and print or send the results using GSM. In short you have to follow same procedure which I have followed for single sensor.
@yusufcemiloglu8315
2 жыл бұрын
Can i do this project with arduino nano with same codes
@ecit
2 жыл бұрын
Yes, make sure to keep all pins as per connection compatible with Arduino Nano. Only you need to change board in my project, select Arduino Nano instead of Arduino Uno
@yusufcemiloglu8315
2 жыл бұрын
@@ecit Which pins should I plug the gsm module into?
@ecit
2 жыл бұрын
@@yusufcemiloglu8315 7(Arduino Nano) to Tx (GSM) 8 (Arduino Nano ) to Rx (GSM) Don't forget to subscribe this channel to get more videos on time
@yusufcemiloglu8315
2 жыл бұрын
@@ecit sir you connected 7 rx , 8tx . Arduino uno and nano pins are differents ?
@ecit
2 жыл бұрын
@@yusufcemiloglu8315 I may made mistake in video but make connections as explained below. In SoftwareSerial mySerial (rxPin, txPin) So, if you write SoftwareSerial mySerial (7, 8) It means Arduino Nano 7 to GSM Tx And Arduino Nano 8 to GSM Rx
@rameshtiru9509
3 жыл бұрын
Which language program it is
@ecit
3 жыл бұрын
Arduino C++
@kennethpotenciano3205
7 ай бұрын
how to convert it to smoke detector instead of gas ??
@ecit
7 ай бұрын
You can set the threshold for smoke and also you can use CO2 sensor or any other sensor that will detect smoke.
@kennethpotenciano3205
7 ай бұрын
where is the code for smoke
@ecit
7 ай бұрын
@@kennethpotenciano3205 you can use the code link provided in description
@johnvincentsuarez5573
2 жыл бұрын
Is this fire alarm system have GUI?
@ecit
2 жыл бұрын
No
@johnvincentsuarez5573
2 жыл бұрын
@@ecit Sir can you send me the circuit diagram including the breadboard wiring?
@ecit
2 жыл бұрын
@@johnvincentsuarez5573 circuit diagram link is mentioned in description, if you watch my video of this playlist, you will learn about interfacing of all components github.com/hiren-tailor/GSM-arduino-fire-alert-system/blob/main/gsm%20arduino%20fire%20alert%20system.png
@azizurahimi7
2 жыл бұрын
Hai. Can I use This code for sim900?
@ecit
2 жыл бұрын
Yes, You can
@azizurahimi7
2 жыл бұрын
@@ecit sir If I take out sensor, buzzer n led.. then I just try.. alarm triggered, that project still can call n sent message to phone?
@ecit
2 жыл бұрын
@@azizurahimi7 yes it can if GSM is working
@azizurahimi7
2 жыл бұрын
@@ecit ok tq sir. I use your code tx n rx ok already .now I call that no at GSM also ok. Just when alarm trigger. I still no receive call n SMS at my phone. Hmm
@ecit
2 жыл бұрын
@@azizurahimi7 check the number that you mentioned in the code? Make sure that format is okay,
@pranavnagvekar636
2 жыл бұрын
Call agar recieve kiya to kya hoga ????
@ecit
2 жыл бұрын
Nothing
@pranavnagvekar636
2 жыл бұрын
@@ecit matlab sirf alert karne ke liye hai vo
@ecit
2 жыл бұрын
@@pranavnagvekar636 yes, you will get alert inform of call
@kennethpotenciano3205
7 ай бұрын
how can i get the code?
@ecit
7 ай бұрын
Code link is provided in description, you can download it from my GitHub page
@zoro_boi739
2 жыл бұрын
hello sir, i tried to run this code and it showing me "Serial port not selected"
@ecit
2 жыл бұрын
In Arduino IDE, go to tools and select the com port and then open the serial Monitor and set the baud rate
@SachinKumar-hj5xc
3 жыл бұрын
Sir plz provide program code for Arduino uno plz sir
@ecit
3 жыл бұрын
Code like is provided in the description
@Srikar337
3 жыл бұрын
How to contact you sir?
@ecit
3 жыл бұрын
hirentailor.rf@gmail.com
@Srikar337
3 жыл бұрын
@@ecit tq sir
@tusharrajput8301
2 жыл бұрын
Sir can I get synopsis
@ecit
2 жыл бұрын
I have not prepared documents for this. However, You can refer circuit diagram and code link given in the description.
@tusharrajput8301
2 жыл бұрын
@@ecit ty sir
@ecit
2 жыл бұрын
@@tusharrajput8301 I am sure you can easily prepare report by watching this video and don't forget to subscribe this channel.
@subhashini.s
23 күн бұрын
Code ?
@ecit
23 күн бұрын
@@subhashini.s code link is mentioned in description
@sitabaishelke9917
3 жыл бұрын
You are Indian
@ecit
3 жыл бұрын
Yes, I am Indian
@indianfireservice24
2 жыл бұрын
i want this project.. give me your contact
@ecit
2 жыл бұрын
Code link is available in the description. You can easily develop by yourself.
Пікірлер: 375