Thanks for covering this again. The forums seem to have a ton of questions about the anteater weekly.
@LMDiesel
2 жыл бұрын
Might need to get me one!
@Fullerperformance01
2 жыл бұрын
I've got mine. Putting it in this week, can't wait to drive it.
@LT1SWAPCOM
Жыл бұрын
I've had the Pro for a while on my truck, and have had issues with it not 2-1 downshifting with ANY throttle input. (TV is fixed, so engine speed, pump output, pressure output affecting something??) It will only 2-1 it if I completely let off the gas. (screen will say 1st gear, but will stay in second) I can adjust TV some but then I won't get 2-3 shift sometimes. Its like I can get one or the other. Also when I hook up a pressure gauge to the TV pressure port on the trans, when commanding 2nd gear, the pressure oscillates up and down a bunch (20 to 60 psi constant jumping around up/down, few times a second. This is also shown on the data logger on the anteater software. Is that normal? I can change the 2nd gear pressure, and the window will move up some, like 30 to 70, but it ALWAYS jumps around. Seems when I start out driving cold, the 2nd gear gov pressure is pretty steady, but longer drive the more it jumps around.
@bandabanderos
2 жыл бұрын
Nice. I’m sure one will eventually end up on my truck. You didn’t talk a lot about lockup- is it fully programmable? Say like zero throttle coasting but you want to use an exhaust brake so you want to keep the TC locked? Or locked vs unlocked shifts?
@FirepunkDiesel
2 жыл бұрын
If you look at the tuning page you can program lockup based on mph, the 48re is not a great trans to downshift in lockup due to bind up and shock load concerns
@user-nf3oq2ge3g
8 ай бұрын
That’s funny I used a Volvo floor shifter so it’s got sequential feel
@Bgray95
2 жыл бұрын
I think I have this already from when you guys did my swap, as mentioned below in comments would it be possible to turn the factory Tow Haul button into a lockup switch?
@Toxicwastesu
2 жыл бұрын
I need this.
@kylefitzherbert9381
2 жыл бұрын
Want one so bad
@benfender5292
2 жыл бұрын
When it comes to adjusting the lever, when u say back it off an 1/8 of an inch do u mean back it off from 100 or zero? Trying to gauge the 75-80%
@hams1198
Жыл бұрын
prob alittle late but from 100%
@demetriuspalmer2992
Жыл бұрын
Do you guys make a FMVB ratchet shifter for the 6.0 Powerstroke or not I'd love to build a manual shifted auto 6.0 but on the floor like a ratchet shifter
@albertopaulino7182
Жыл бұрын
Hi guys I just buy an pro version and I want to install the tap shift to a button, do you have any video that show how to do or any manual
@kingleonidas6796
Жыл бұрын
So does anyone thing this would work on a 2001 and run a ratchet shifter and use two buttons on the shifter for manual mode?
@FirepunkDiesel
Жыл бұрын
Yes, we've done that before
@joshcarter6974
2 жыл бұрын
How does the anteater work in a sled pulling application? Could I leave in third and let it lock up on its own or will a 48re not like that?
@FirepunkDiesel
2 жыл бұрын
Yes, you can leave in 3rd and have the anteater command lockup at your preferred mph
@joshcarter6974
2 жыл бұрын
@@FirepunkDiesel will a 48re be short lived doing it or not? Built trans with all billet shafts obviously
@markrich3271
2 жыл бұрын
@Firepunk Diesel I heard you mention 03+ Can this be used with a 98.5 - 02 47re?
@FirepunkDiesel
2 жыл бұрын
Yes as long as you install 2000+ electronics on your vb
@brunnettfab9592
2 жыл бұрын
@@FirepunkDiesel do you have all the functions such as Manuel mode and do you need to use the flat line tunes for this trucks? Also do you need the static lever?
@kellymichael7362
Жыл бұрын
How tricky is it to put one in a '93 1st gen?
@jodygannon4939
Жыл бұрын
It looks like PNRD works in regular mode, will it function (change) while tap shifting in manual mode?
@FirepunkDiesel
Жыл бұрын
Yes, PRND display is not effected
@bigmurph1447
2 жыл бұрын
be nice if u could make this work on 96-98 12v
@FirepunkDiesel
2 жыл бұрын
it does, you just need to swap 2000+ electronics on the valve body
@bigmurph1447
2 жыл бұрын
@@FirepunkDiesel ok u guys should make a shifter for the older trucks with the shifter switch on it
@FirepunkDiesel
2 жыл бұрын
When we install in house, we remove oem 2nd Gen shifter, cut and tig Weld new tap shifter on the end of it
@jordanmercredi3740
2 жыл бұрын
I have and appendage that looks like an anteater can i have one lol
@aconservativeusa
Жыл бұрын
.....did he say "o4&1/2" Mannnnnnn
@JCSDieselPerformance
11 ай бұрын
Thats what it is, in 04.5 they changed the engine/transmission quite a bit
@peytonmorris8730
2 жыл бұрын
I have an anteater I bought not too long ago from you guys shifts are all where I want but the 2-3 shift under light throttle is a bit harsh Basically slams into 3rd and also shifts a bit harsh into overdrive with light throttle but smooth under moderate to full throttle shifts smooth how do I go about fixing that thanks
@keanekriebel7420
Жыл бұрын
I have the same problem but I think it’s because it’s direct line pressure staying the same constantly so that’s why it shifts super hard like that
@jonathangarzon2798
2 жыл бұрын
Save some money, be a man, buy a manual
@joshuaquilliam2887
2 жыл бұрын
And go slow? Nah I'll keep rocking my comp 1
@jonathangarzon2798
2 жыл бұрын
@@joshuaquilliam2887 damn you're such a terrible driver you need a computer otherwise you're slow? My condolences
Пікірлер: 38