I have shown the rest of the repair parts in the following videos
@deana8202
2 жыл бұрын
Good job. Satisfaction in fixing something instead of trashing it.
@inmatejason
Жыл бұрын
i damaged my accords aluminum hood and no shop would touch it, only option they told me was to buy a new one.
@_demon1k_
Жыл бұрын
Repairing aluminum parts is quite difficult, so craftsmen try to refuse such work and recommend replacing the part. I decided to try to repair it as a temporary solution until the new hood was delivered
@juliodelerme7568
3 жыл бұрын
Great job!
@LordLoMR2
8 ай бұрын
So much work, better off buying a new one. 😂
@_demon1k_
8 ай бұрын
This was to gain experience working with aluminum. Later I did as you say)
@brianjones864
2 жыл бұрын
Well fk it I’m going after my dented ass tailgate. No stamped areas so I think I’m good
@rolandoalvex200
Жыл бұрын
Usamos martillos de plásticos de goma dura y suave y de fenólica madera
@_demon1k_
Жыл бұрын
Sí, estos martillos funcionarían mejor, pero no tenía muchas herramientas en ese momento
@newauraxx
4 жыл бұрын
Would a rubber mallet be good to use on the back of the hood or would that cause to much damage
@_demon1k_
4 жыл бұрын
Yes, because the aluminum hood needs to be heated, it is easy to damage the paint even with a rubber mallet
@ismaelcarrillo3956
Жыл бұрын
Use a polyurethane mallet. It had the perfect impact results. Aluminum is very stubborn.
@clinteast7476
Жыл бұрын
I must admit it looks like shet, but look at all the money saved.
@_demon1k_
Жыл бұрын
This repair was as an experience with aluminum, maybe someone will be useful for their repair. But this repair only gives time to save up money to replace the part
@zesusflacko
3 ай бұрын
How would you go about straightening an aluminum hood?
@_demon1k_
3 ай бұрын
Aluminum is also metal and can be straightened, but only small bends, I was just practicing on this hood, but such damage should not be repaired
@ravens101100
4 жыл бұрын
Looked like a waste of time
@_demon1k_
4 жыл бұрын
Hood straightening was done for temporary installation until the arrival of new parts and for gaining experience in working with aluminum. Watch the following videos and you will understand how it looks at the end of the work.
@joserangel1650
2 жыл бұрын
The hood cost $1000 you guys did a good job I work on a body shop looks like you have some skills
@ismaelcarrillo3956
Жыл бұрын
@@joserangel1650 $1000? Lol. Where do you do ur shopping.
@bash8387
Жыл бұрын
I can’t get my hood open cause my right side of the hood got pushed it, how can I open it
@_demon1k_
Жыл бұрын
Without a photo or video it's hard to know how to help
@bfocsa
2 жыл бұрын
If i have a hole in it , how can it be fixed?
@_demon1k_
2 жыл бұрын
TIG welding only. The hood is made of aluminum
@_demon1k_
Жыл бұрын
@Will Swift mig welding will give more severe metal deformation, but will also work if there is no other. Yes, it is better to heat aluminum before all work
Пікірлер: 33