Awesome video! My first wacky rig used heat shrink tubing thanks to your instructions.
@A.Blair_Fishing
2 жыл бұрын
Great tips. Never would have thought of that. Subscribed good luck with the content!
@Im118ish
4 жыл бұрын
Important detail is that they make transparent heatshrink. I definitely prefer the clear stuff for obvious reasons.
@HobbyAddictions
3 жыл бұрын
clear is what I use now
@donnysath9084
2 жыл бұрын
where do you get the shrink wrap at?
@HobbyAddictions
2 жыл бұрын
@@donnysath9084 any hardware store
@Im118ish
2 жыл бұрын
@@donnysath9084 easily on Amazon,but not sure how to aquire smaller quantities(may end up with 10feet) maybe in the electrical department of Lowes/Home Depot/local hardware shop...ya want clear 3/8" Inner Diameter,,preferably DWP( dual wall poly)...not expensive,& will pay for itself via saving senkos in no time (especially if ya throw Yamamotos) løl Not sure of other sizes being useful... 1/2" ID should shrink down if its 3:1 shrink ratio(most common material is 2:1), but will be extra bulky which may actually be beneficial-mimicking a swollen egg sack, but I haven't vetted that. 1/4" ID works good on trick worms, but is too tight on normal size senkos Good luck.
@donnysath9084
2 жыл бұрын
Thanks a lot for your reply both of you! I'm in NW WI.
@DetroitFishigan
3 жыл бұрын
Excellent tip 🥃🍻
@heartandhandbyjanelle4450
7 жыл бұрын
Great tutorial thanks
@backintofishing6716
5 жыл бұрын
Good tip, I'll give it a try.
@mrenfilade7178
4 жыл бұрын
Ive been o-ring free for years, too -- almost as big of a scam as an $8 bag of senkos xD -- the only thing I'd add is using clear tubing in case you're using lighter colors and want to keep the continuity of your pattern. Here's what I use: smile.amazon.com/gp/product/B074HWVM33/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1
@orlandoharmon4738
Ай бұрын
Or you could just by Clout worms and avoid all that. yammamoto worms seem fragile to me.
@dansingletary7891
6 жыл бұрын
Great tips!
@johnmillspaugh2129
6 жыл бұрын
I am having difficulty seeing exactly how you are hooking it up. Are you going straight through the shrink tube into the worm and out the center of the worm or perhaps more to the edge of the worm? Hope that makes sense.
@HobbyAddictions
6 жыл бұрын
Hey John, so, I can go right through the shrink tube or slide it though depending on how I want the action when I throw it wacky or I slide a longer shank hook through and it D rig. When I set up some worms for D Rig, I actually have have a wider piece of tubing so the hook lays down along the worm more; this gives it better action and helps set the work standing up straight when you move it along the bottom. I hope I answered your question-let me know if I'm off base.
@roberthamlin6638
Жыл бұрын
@@HobbyAddictions I had to cut the tip off the tail off of a zoom trick worm in order to get the worm to go through the shrink tubing. It’s a tight squeeze going through 1/4 inch tubing.
@bdigrino6809
3 жыл бұрын
Excellent video! Great alternative to o-rings. Mind sharing your source for purchase? Would like to order in 1/4 and 3/8.
@HobbyAddictions
3 жыл бұрын
If you’re asking about the shrink tube, I picked it up from Lowe’s hardware, but any hardware store will have it in the electrical section. I’m sure Amazon has it too. What’s nice if you keep it lighter and the shrink tube to with you, you always have it available to cut and make the size you want you don’t have to worry about going to a store and buying the O rings.
@bdigrino6809
3 жыл бұрын
Thanks so much for the quick response! Much appreciated.
@mauricemiller1128
3 жыл бұрын
Why shrink it? The hook will hold it in place and if you don’t shrink it then you can move it in case you want to go from wacky rig to Neko rig you can just take the hook out slide the tube forward then reinsert the hook add your nail weight and you have a Neko rig quick and easy.
@HobbyAddictions
3 жыл бұрын
I heat just to keep it in place, but your right about moving it around
@mauricemiller1128
3 жыл бұрын
@@HobbyAddictions thank you sir and I do like the tubes over the rings but I never thought of using shrink tub I’m an electrician and I can get those at work for free so I’ll try that out.
@Tom-ic7hw
3 жыл бұрын
thats what i do except i found a whole roll of clear in my garage must be 6 ft keeps the color of the senco intact and i use a heat gun...anyway great info should help lots of people can u do a video on what to do with the wacky tool and a million o rings
@HobbyAddictions
3 жыл бұрын
good idea using the clear, and funny thing; can't find the wacky tube.
@samyish
6 жыл бұрын
What about hooking through the center of the tubing and the worm?
@YouMe-gx5uu
6 жыл бұрын
Samy Ismael I thought the same thing, but ive seen guys put the hook through the shrink tube only. And it works that way as well. Plus you can hook it straight that way instead of putting it under the shrink tube. Hope this helps. God Bless.
@zafotbeeb
5 жыл бұрын
Been doing this for awhile now . I use a heat gun rather than a torch. I first learned this trick from NDangler.com
@HobbyAddictions
3 жыл бұрын
I picked up a heat gun, and tried it but still like the small area the lighter makes. I melted a few worms with my heat gun; probably just me though
@highonlifefishing4007
3 жыл бұрын
I dont even use an o ring 😂🥺
@robertstewart1630
2 жыл бұрын
What size of the shrink tube?
@ercly9382
2 жыл бұрын
1/4" and 3/8" diameter
@roccogant4057
5 жыл бұрын
just buy the o-rings....they are cheap enuff...
@HobbyAddictions
5 жыл бұрын
I still use O rings on a pinch but it's not all about price, the shrink tube doesn't slide off like the rings. Just another alternative, thanks for the comment
@raydalton1110
5 жыл бұрын
Rocco r u a troll? , did u see the video or dont understand ? O rings make u lose EXPENSIVE worms !
Пікірлер: 36