Stop buying Samsung it’s the worst tv out there, can’t believe ppl don’t read reviews.
@GidFix-pl3lg
9 ай бұрын
Reading reviews is highly recommended but i believe Samsung still has some good TVs out there.
@justgod5579
Ай бұрын
So please why it happens like that because i was having the same issue on my Qled tv
@justgod5579
Ай бұрын
It's very expensive tv so why they refused to do it quality?
@justgod5579
Ай бұрын
Samsung people are very wicked
@gabidray
17 күн бұрын
Thank you for the video. I have same tv with same issue. I did few test with tape and finally manage to find that blocking number 17 pin get me image but there are a few small black horizontal line on the image. Looks like pin 17 go to the VGH on the right side. Voltage on left vgh is 24v and vgh on the right reads 6v. Is there somthing else that i can do? Thanks!!
@bertha4085
Жыл бұрын
Thank you for sharing your knowledge with us👍
@JulianHols
12 күн бұрын
Hey, great video! I had the same problem and I also found the pin, which caused the restart. But after i taped it the light remains on but i don't have a picture. Do you have an idea why this happend?
@GidFix-pl3lg
10 күн бұрын
@JulianHols Hi, were you getting any sound or pictures when the problem started (when the tv was power cycling). After tapping, if you are not getting any sound or pictures, you may need to tape multiple pins. I will suggest disconnecting the ribbon cables one after the other on the left and right to see if you get half a picture or at least some sound.
@mikefox3542
6 күн бұрын
To me it looks like the power supply isn't delivering enough current for the demand.
@GidFix-pl3lg
2 күн бұрын
@mikefox3542 You can be right, I have come to the realization that several problems can give the same symptoms.
@deadlyllamagod8201
8 ай бұрын
What is the ribbon called? Im thinking of just replacing it.
@GidFix-pl3lg
8 ай бұрын
Are you referring to the ribbon that connects the left and right panel driver boards?
@jujigatame4800
2 ай бұрын
howd you go
@DominieDirtch
9 ай бұрын
Great video. I have AU8000 50” I am able to stop boot loop, consistent backlight, sound, and proper standby mode (solid red light when TV off) but I still can’t get any picture unfortunately. I replaced both the power and the main board before I got to this point of pin taping, so I’m positive it’s this. I just haven’t covered the right pins on the ribbon I guess. Close to giving up.
@JohnJoDan-r1m
5 ай бұрын
Excellent explanation about your troubleshooting. You explain very well the step by step sequence. That is very helpful, keep up the good work.
@GidFix-pl3lg
5 ай бұрын
Thanks for the encouragement.
@aguy-b5q
2 ай бұрын
Great info. I had similar issue with a lightly used, four year 75" Samsung QN75Q60TAFXZA. Ordered and replaced the main board $80 and that did not fix the issue so tried this tape method. Covered pins 7 & 8 hoping that would help but the entire left 1/3 of the screen was completing black. Then I covered pins 1-4 and hit the jackpot as 100% of the screen works and looks perfect.
@GidFix-pl3lg
Ай бұрын
@user-dt3vq5lu1p Comments like yours make me happy. I'm very glad you could get it working again.
@mduduzishabalala2348
Ай бұрын
So after you put the tape how many months can last you the tv?
@GidFix-pl3lg
Ай бұрын
@@mduduzishabalala2348 Its been close to a year now and the tv is still working.
@mduduzishabalala2348
Ай бұрын
@@GidFix-pl3lg wow that's great man
@mduduzishabalala2348
Ай бұрын
I also fixed two tv Samsung 58 " is working
@samuelcofe1075
10 ай бұрын
My name is legacy I had come across the problem with 55inchs n I work it
@GidFix-pl3lg
10 ай бұрын
Thanks for the comment. Glad it worked for you.
@voicetube
4 ай бұрын
I'm curious to see what you think about my issue: I have a Samsung 75 inch LCD (circa 2019) model television. Not sure if you know the answer to this (or anybody watching) but my symptoms are that when you go to turn it on, the (Samsung) logo comes on solid at first… and then these horizontal lines develop (which are sort of similar to the horizontal lines we see when you first used the tape)... and then the TV shuts off and goes through that cycle again. (And again) for a while… But it does finally turn on within 15 minutes and works fine. Usually for 10 minutes + it reboots, over and over again. When it's just about to turn on and work (which it does usually in less than 15 minutes of letting it cycle like this) it finally gets past the logo and you start to see the main MENU screen, etc. and then the horizontal lines develop and then it shuts off ... and restarts and then FINALLY, it comes on for a few seconds (with the sound of whatever the TV show is that's playing or whatever) then, it usually goes through one more cycle... and then it stays on (and works perfectly, from that point on (until you turn the TV off again). I'm wondering if that's a power board issue (rather than a main board issue, or the issue you had)? According to the seller who sold it to me, It did start occurring, just after a lightning storm. Do you think replacing the whole power board would do the trick in fixing it? Short of that, is there a particular part (or two) on the power board that would usually be the culprit that I could replace for a lot less money than replacing the whole power board? Even if I have to pay about 125 bucks for a new pwr board, I think it would be worth it. (It's a great TV once it stays on). [After watching your video, I'm guessing it's probably a similar panel problem and rather than open it up and try the tape trick, etc., since it does turn on and stay on after 15 minutes or less, I think I'll just live with it until I can afford to get a new TV. Thank you for posting this video] 🙂
@GidFix-pl3lg
4 ай бұрын
Hi, thanks for the detailed explanation about your tv and sorry for the late response. Your issue is quite unique and may be a problem from one or multiple sources. Lightning could have partially affected the power supply or both the power supply and panel itself. Usually, i would try to do some elimination. Since you haven't disassembled, it could be best to use it as it is. However, it may eventually stop working. The first thing i would try is to disconnect the motherboard from the powerboard, and switch it on and test the voltages that feed the motherboard with a multimeter. Ensure the tv has been off for a while so that you can provide the same conditions to replicate the fault. If the voltages fluctuate several times before a constant voltage is achieved, then it may be the powerboard. My reservation is with the horizontal lines that show up every time. That could mean nothing or could be an indication of a panel board or panel issue. You could also listen very closely to the TV if there are any buzzing or unfamiliar sounds when the tv is power cycling. If the powerboard gives constant voltage after disconnecting the motherboard, then try disconnecting the panel ribbon cables from the tcon board or motherboard (depending if this tv has a tcon board or is built into the motherboard), switch it on and test the voltage for fluctuations. If it doesn't fluctuate, then the panel driver board or panel itself could be the issue. If you don't have a multimeter, do the above and see how the backlights behave. I hope this can help you for now. Thanks.
@dsstudios5425
10 ай бұрын
I did this and the screen is now white and pics are negative pliz help
@GidFix-pl3lg
10 ай бұрын
I am not really sure what you mean by "pic are negative". Make sure you haven't swapped the ribbon cables. Also, a white screen means you are probably covering more pins than expected. Try to narrow it down and cover as little pins as possible. It requires a lot of trial and patience.
@decaalv
9 ай бұрын
I tried the tape trick and could not make it to work. The best I could do was to stop the boot loop.
@GidFix-pl3lg
9 ай бұрын
After stopping the bootloop, what do you get on the screen now? Please note that you may have to adjust the tape several times on different pins until you get a good picture. You will need lots of time and patience to eliminate the right one.
@snowyowlnugget
7 ай бұрын
@@GidFix-pl3lg Hello, I've found mine to be a similar model, presumably with the same 'panel issue", and GUESS WHAT, THE PANEL itself is FINE, but something, like you said, must have shorted in the chips on the film, and mine seems to be coming from the right side driver board, but when I tape over the specific pin that I found, (Which seems to be a ground for all i know), it will stop bootlooping, but it now displays no image or sound. when I remove the tape, it can be started but only via the hot-wire method of plugging the cable in after pressing the power button. Any Ideas? (Specific model is the UN70NU6900FXZA), and it's the second pin if you're counting from the left. i.imgur.com/3qWhGPS.jpg
@jordannaumceski2269
5 ай бұрын
Hello, i have Samsung TV, model LE37C530F1W. When the power cord is unplugged and plugged back in, the tv starts itself and is bootlooping about 10 times, then is working normal. Everything is fine until the power cord is unplugged again and it's doing the same thing. I cannot find nothing suspicius, i changed the main big capacitor but it does the same thing. What could be the problem ? Thanks
@GidFix-pl3lg
5 ай бұрын
Try disconnecting the motherboard cable from the power supply board. Then, plug it in and use a multimeter to check the output voltage to the motherboard on power supply to see if there are voltage fluctuations. If the voltage is stable, then it's likely your motherboard causing that.
@DominieDirtch
9 ай бұрын
Great video. I have AU8000 50” I am able to stop boot loop, consistent backlight, sound, and proper standby mode (solid red light when TV off) but I still can’t get any picture unfortunately. I replaced both the power and the main board before I got to this point of pin taping, so I’m positive it’s this. I just haven’t covered the right pins on the ribbon I guess. Close to giving up.
@GidFix-pl3lg
9 ай бұрын
It can be frustrating, but one thing to note is that sometimes the taping would just stop the reboot, but no picture appears, just backlight and sound. In that case, you may need to do as illustrated in this video: m.kzitem.info/news/bejne/p7Cummujp2Wkno4&pp=ygUGZ2lkZml4 I would recommend checking out the video by powerled electronics. The process is delicate. Usually, a short in the panel is just like a cracked screen, almost useless. If you use the process, don't forget to remove the tape. Thanks for the comment.
@ericanderson85
4 ай бұрын
It worked for me! It was a little tedious working with the tape and narrowing it down to just 1 pin but it actually went faster than I expected. There are some slightly darker lines visible up close but it is absolutely usable.
@GidFix-pl3lg
4 ай бұрын
I'm glad it worked. The TV is still working perfectly to date. Yes, there are lines but only visible when very close to the TV.
@robertobullares4845
3 ай бұрын
cortaste las uñas jajajajjaj
@bhawanjitsingh6283
Ай бұрын
I have 85 inch Samsung tv it has relay clicking problem …can you help me with guidance ?
@GidFix-pl3lg
Ай бұрын
Clicking sound could be a power board issue. Does your TV keep restarting?
@bhawanjitsingh6283
Ай бұрын
@@GidFix-pl3lg yes tv restarting
@GidFix-pl3lg
Ай бұрын
@@bhawanjitsingh6283 Your TV is quite huge. If you are able to open the back, try testing the power board with a multimeter but without a connection to the tv panel from a motherboard. This is one test to eliminate the problem.
@yky1526
8 ай бұрын
Since there's a short, is it not possible to do a continuity test to see which lines were shorted?
@GidFix-pl3lg
8 ай бұрын
Thanks for the question. Unfortunately, this short seems to be in the panel or screen so it makes it difficult to do such a test.
@SD4MEnow
10 ай бұрын
Thank you, thank you, thank you! I had the same problem with my 55-inch samsung 6000 series. Problem Solved 👍🏼🎉
@GidFix-pl3lg
10 ай бұрын
I'm glad it worked. I hope it lasts. It's been 4 months, and mine still works.
@SD4MEnow
10 ай бұрын
@@GidFix-pl3lg that's promising!
@IceMan-xy1yt
7 ай бұрын
Dude you are a God amongst men. Thank you
@GidFix-pl3lg
7 ай бұрын
I am not a God sir but i am glad i could help. Take care.
@zwoelebertha
9 ай бұрын
What kind of tape did you use?
@GidFix-pl3lg
9 ай бұрын
Hi, just a regular scotch tape.
@BMWGROUP-zw7bf
8 ай бұрын
Samsung tv ue46d5700rsxzg NEUES MAINBORD BN-01660A-BN-04659B UND NEUES BN44-00423A----www.youtube.com/@BMWGROUP-zw7bf/videos
@Rafal0r
9 ай бұрын
After covering several pins with tape = no image, backlight is on. After covering the first pin with tape = no image, backlight is on. When nothing is taped, the TV does not turn on/the red LED flashes and the TV backlight blinks Samsung Crystal UHD 50” TU8002
@GidFix-pl3lg
9 ай бұрын
I am assuming you are taping the connector at the right side of the panel board. Do you get any sound in any of your scenarios? Disconnect the ribbon cable to the motherboard and check if the backlight will still blink when turned on. If you have a multimeter, you could check if your panel board has voltage coming to them.
@DoggieStyle-xo6vb
5 ай бұрын
Help, the right side I put tape exactly where taped yours, it stopped the turning on/off. Stay on but I have no picture now. Help?
@GidFix-pl3lg
5 ай бұрын
The spot i taped in the video may be different for your TV. You may have to try taping different spots to get it working. You will need lots of patience to figure the right pins to tape.
Пікірлер: 60