Thanks! This fix is going to save me from wasting a bunch of labels.
@testube
Жыл бұрын
OMG - thanks so much! It worked. This has been driving me crazy for years, and I assumed it was hardcoded and could not be changed.
@foolishal
Жыл бұрын
Thanks! I have been wanting to fix this for years. This solved the problem instantly.
@TheRealAndyB.
2 жыл бұрын
You the man. Finally a video that really helps. You gain a new subscriber. 👍🏻👍🏻👍🏻👍🏻
@K_Shea
Жыл бұрын
Why this printer continues to randomly go into this 2 label start-up is strange so once again your fix came to the rescue :) thank you
@MrMikeD28
Жыл бұрын
THANK YOU SO MUCH! Now I can turn my printer off without wasting labels everything time i turn it on! What a BIG help!
@calvinkim4067
2 жыл бұрын
Wow I thought this is something that can’t be fixed! Thank you so much :)
@danacostello5908
Жыл бұрын
I thought it was just something normal.
@AbdallaBadran
2 жыл бұрын
Thanks man, you helped a lot. It worked with Zebra GK420t.
@buffalocentric
3 жыл бұрын
This was awesome. Thanks a lot. This is something that's been annoying me about my Zebra zp 450 for a while.
@thecollegepicker
3 жыл бұрын
It's easier on the zp450 you can do it this way or the other video settings.
@buffalocentric
3 жыл бұрын
@@thecollegepicker I followed along and did it. Thanks again.
@thecollegepicker
3 жыл бұрын
Awesome, 🙌 successful tutorial in my book 🤘
@osmanalisyed373
3 жыл бұрын
Its working, Thank you so much for this Vid. My GC420t (EPL) printer has same issue wasting about 20 labels. And now is working properly.
@thecollegepicker
3 жыл бұрын
You are welcome
@dudestoked
2 жыл бұрын
Dude you are AWESOME. Thank you for the help and fix.
@thecollegepicker
2 жыл бұрын
You are welcome 🤠
@LawrenceKincheloe
Жыл бұрын
This saved so many blank labels!
@citizentrucker
3 жыл бұрын
Thanks to your videos and a couple others, I was able to get ahold of a cheap 2844 last year that supposedly didn't work and got it working 😁 just needed a new head and the gap censor at the top was knocked out of place. Easy peasy! It took me almost a year to figure out if I slowed it down it'd increase the label print quality 🤣😂 Side question, have you tried to do the usb to c with a 2844?
@shittychannel4860
3 жыл бұрын
The 2844 wont work with phones if thats what you mean, USB-A to USB-C would work. If you are connecting it to a new macbook or so with USB C ports.
@brandonhann2051
2 жыл бұрын
Such an awesome little fix. Thanks!
@thecollegepicker
2 жыл бұрын
You are welcome
@RonWaller
3 жыл бұрын
What 4x6 thermal labels do recommend? Getting Zebra printer need small amount of labels to get started. Thank
@TheResellerCollab
3 жыл бұрын
Thank you for this video!!
@msheraz86
4 ай бұрын
Awesome!! I was actually looking for a solution to put my printer to sleep as I rarely use it but this one is way better solution (I do find it annoying that it wastes 2 labels when powering up, so this was a huge help) Thanks!! Just turned it off from the back and turned it back on, the light went red and then green. No labels wasted 😁
@thecollegepicker
4 ай бұрын
You are welcome!
@TonerRefillVideos
Жыл бұрын
Great solution! Thank you!
@eshaansharma280
3 жыл бұрын
Damn this is so helpful and money saver !!!!
@thecollegepicker
3 жыл бұрын
💸💸💸💸
@rabahboute8913
3 жыл бұрын
Hi Erik I have a datasouth fastmark M5 kind expensive machines the issue that I'm having is after first print if I send a send print it will start and stops an d I get a blinking red light I need to power off the printer and hold the button to reset it . Any advise? Thank you also when j print on pdf I do customize 95% please advise thank you
@lindaturner9680
3 жыл бұрын
That label.... On your hat. What's the setting to center it? 🤣 Your favorite OCD 🐜 Love you!
@thecollegepicker
3 жыл бұрын
Its a new style =)
@Average-Joe
3 жыл бұрын
Thank you! Been driving me nuts for months! LOL
@thecollegepicker
3 жыл бұрын
You are welcome
@Eric1ssa
2 жыл бұрын
Very nice tip, thanks, one question, how do you chenge this ^MFNN archive? Wich software do you use?
@MrSoarman
3 жыл бұрын
You are our Zebra god, thank you.
@thecollegepicker
3 жыл бұрын
😂🙏🙏
@ninjasuvarna5812
Жыл бұрын
work perfectly, man. Thank you from Indonesia 👍👍
@nowski85
Жыл бұрын
Awesome! Thank you🙏 Your vids are great!
@zeshaune4673
2 жыл бұрын
thank you so much it worked perfectly
@azazelagata2439
Жыл бұрын
Great video , thank you
@kylewilliams4409
3 жыл бұрын
How do I change this back to it's original setting? After following your video exactly my Zabra 2844 still spits out an extra label after it prints a single label.
@donpassenger5148
3 ай бұрын
worked like a charm, thank you
@sanjaykumarshrivastav7958
3 жыл бұрын
Sir,I have some problem in gc 420 printer.i want to take print in 2 up transparent label size 30*20mm . kindly reply how we can take the printing
@xxfabixx9036
2 жыл бұрын
Great!! It solved my problem 😀
@webtlz
Жыл бұрын
Awesome. Your file worked on ZP450. Thanks~~.
@byelias
2 жыл бұрын
Valeu amigo, resolveu meu problema, Muito Obrigado!!!
@AuroSya
3 ай бұрын
Life saver! Thank you so much!
@raymondrosado8561
Жыл бұрын
Hey great video, very helpful. Can you tell me how to adjust the top spacing on the label? My label prints at the very top edge of the paper and I would like to have it start printing a bit lower
@lockdown318
Жыл бұрын
Bump. Got exactly the same issue.
@kulot326
3 жыл бұрын
Yey!!!! No more spitting labels!!! Thank you!!!
@thecollegepicker
3 жыл бұрын
Wohoooo 🙌🙌🙌
@kulot326
3 жыл бұрын
Have a great day!!! Stay safe!!!! 😊😊😊😊
@petemc1019
2 жыл бұрын
I've seem to have hit a problem with the downloaded file. When I open the file I don't see the ""Apply" button. When I click ok, nothing happens and no configuration label is printed. If I try to print the configuration label by holding the printer button for one flash, it prints a short report of approx 6 lines of data. Any ideas what I'm doing wrong?
@p1nt0n6
3 жыл бұрын
Thanks dude...you save my label..😂👍👍 🍻🍻🍻
@thecollegepicker
3 жыл бұрын
Oh good, happy to help =)
@ghaforyaqubi439
Жыл бұрын
Even though I had another printer, by using the setting I could fix it. thanks a lot
@thecollegepicker
Жыл бұрын
You are welcome. It uses the same language 🤝
@ChaboyAnthony
3 жыл бұрын
Thanks for this tip! I've been curious for sometime, and you may know the answer. Is there a way to print on individual labels? Or are the labels the printer shoots out in those situation considered "unprintable"?
@thecollegepicker
3 жыл бұрын
You are welcome, Im not quite sure I understand the question. You can roll them back up and reuse them?
@ChaboyAnthony
3 жыл бұрын
@@thecollegepicker If the printer spits 1 blank label out as a test - can that be rolled back into the rest of the labels in the printer even though you have to break it off once printed? I figure the label wouldn't stay in place if rolled back up since the rest of the labels are attached together. I hope I worded that better!
@thecollegepicker
3 жыл бұрын
@@ChaboyAnthony Once its ripped its hard to use, I use them for scrap paper or to cover address during an unboxing.
@rottenboy7352
2 жыл бұрын
i tape use a clear gift wrapping tape and put the tape on the back, i roll it back in and it works fine
@exelnope7365
2 жыл бұрын
very very happy great job it works perfectly also works on a zebra ZT230
@thecollegepicker
2 жыл бұрын
You are welcome ☺️
@FramesiAustralia
3 жыл бұрын
Thank you for that, works great. Do you know how to print lables darker?
@TimDonk
2 жыл бұрын
Raise the darkness level in printer properties.
@neerajmehta1199
4 ай бұрын
Thanks for sharing your tips and tricks. I was able to send the file to my ZD410 printer and changed the HEAD CLOSE to No Motion. My problem is that I use an application to print a label that goes on to a shoe box. My user will be printing just one label at a time. The printer is printing the label fine but a blank label is printer after each label I print. How do I fix it. I am using 2.00x1.25 labels. Thanks in advance!
Жыл бұрын
Thank you. I fixed my printer with your recommendation. I find it so stupid printer manufacturers want users to sacrifice and waste material (that costs us money) in order to calibrate the printer. There should be a better way for this.
@zacharyradford
3 жыл бұрын
Do you know if the Bartender Driver Fix will work with the Deli DL-770D (or if there's any harm in attempting it)?
@thecollegepicker
3 жыл бұрын
The deli should not be calibrating on boot or opening top. I am not sure on that, I would shoot their custom support an email
@tusgavobh
3 жыл бұрын
Hi my friend ! I have a a zebra tlp2742 , but I cant configure to print! can you help??
@miloslaw
2 жыл бұрын
Thank you!
@riverahtdo
Жыл бұрын
Excelente, muchas gracias, buen video y funciona perfecto
@danhaberman4391
5 ай бұрын
I see the description and click on the 3 dots but there is not any link to download a file. I must be missing something here. Please help and Thank you! Dan I have The ZP 450. I don`t if that makes a difference.
@IrfanAli-do4bo
Жыл бұрын
Can u plz guide me about the error head element bad. i have zebra 105 s plus
@BB-cm8wn
2 жыл бұрын
I'm a 52 year old grandma and even I could make this change. Thank you!
@thecollegepicker
2 жыл бұрын
Happy to help 🤝 good job grandma!
@bt7522
Жыл бұрын
I have the opposite problem on my printer (Not zebra but maybe you can help) If I don't turn it off, after a few hours then it wastes the 1st label. If I power off right away after use and turn on a few days later then it doesn't waste the label. Also within 1st hour after last print, if not powered it, 3-4 times it readjusts the paper backwards bit by bit each time, maybe that's why it then wastes a label, but why is it readjusting the paper in standby?
@sassypantscpa286
3 жыл бұрын
I have a different problem. I did this fix and the calibration page shows no motion as it should. But my printer prints a label and then advances two blank labels and starts flashing red. Any ideas? I bought used and did a bunch of “fixes” and it was working properly. Then, I changed the darkness setting today and now it keeps advancing two and then blinking red after a good print...not before. Thanks!
@thecollegepicker
3 жыл бұрын
Oh no! Try another recalibration and see if that helps.
@Murugan689
Ай бұрын
thank you so much sir
@warriorfire8103
2 жыл бұрын
So if you have to change this back, how do you do that? Just resend the file?
@hassankhlifat3372
2 жыл бұрын
THANK YOUUUU SOOO MUCH YOU ARE THE BEST
@thecollegepicker
2 жыл бұрын
You are welcome 🤠
@TimDonk
2 жыл бұрын
Mine never prints the settings sheet like the one yours prints, it prints a short list of settings (15 lines)
@petro1257
2 жыл бұрын
Thank you....thank you....THANK YOU!
@Gogonano
Жыл бұрын
Can anyone confirm it working on ZD220 model? Wasting crazy amount of labels. Also if you want to print 1 label it randomly starts to print 10 empty labels or with messed up text. First Zebra printer here and not very good experience so far.
@xameleoninfusion8094
3 ай бұрын
Hey man! I have absolutely the same problem but with a Honeywell PC42D - will this work for my printer? I need your opinion before loading this file as my printer is not Zebra.
@mueez46854
Жыл бұрын
Thnx bro❤❤❤❤😍 love u
@ibrahimkonteh5829
Жыл бұрын
How can I solve my ZEBRA GX430t NETPRT44 QS1 Labels that are printing automatically when you scan the label?
@MrMikeD28
Жыл бұрын
Where to go to learn the commands like you made in the file?
@tenaciously.discovering
3 жыл бұрын
Okay I have a brand new problem that just started this morning when I have a bunch of labels to print: my Munbyn label printer is all of a sudden printing as if it’s zoomed in, with bigger print and a bunch cut off around the edges. And I mean a bunch. I’ve messed with it a ton trying to figure it out and it’s driving me crazy because the settings are the same, 4x6 paper size is chosen, etc. I don’t understand and need help ASAP. Thank you!!
@shittychannel4860
3 жыл бұрын
Sounds interesting. I would contact their support. Could be a bad printer.
@crabmanclan1141
3 жыл бұрын
But in my case I use the 2"x1" and the 4"x6" labels.... It's going to work anyway? I switch the labels when I need it...
@thecollegepicker
3 жыл бұрын
You would have to run a calibration manually when you switch label rolls.
@gere364
Жыл бұрын
What driver is better? Zebra Zdesigner or the seagull?
@joshuafernandes5223
5 ай бұрын
can the above file you've provided in the description be used for other printer brands.
@MahmudHasanMenon
11 ай бұрын
same for zebra xi4 . can you show me how to stop it?
@obu2108
Жыл бұрын
Thanks man👍
@thecollegepicker
Жыл бұрын
You are welcome.
@SwapPartLLC
7 ай бұрын
This has bothered me for years. I remember one time when they were having power issues in my area, the power went out about 15 times in a couple hours. It was just a couple seconds each time, but it was enough to make the printer calibrate. I had to rewind all the labels afterwards.
@vincentdymanus6686
2 жыл бұрын
Where can I find the file that needs to be downloaded?
@JustCallMeInsane
3 жыл бұрын
I've noticed some zebra printers with damaged USB ports that are loose or pushed in. Would these be worth trying to fix or possible to fix?
@thecollegepicker
3 жыл бұрын
Definitely possible but probably not worth it for most people.
@JustCallMeInsane
3 жыл бұрын
@@thecollegepicker Darn. Maybe one day I'll try it for fun then haha. Ty for the reply!
@thecollegepicker
3 жыл бұрын
Good luck with surgery 😷
@nicolasdmitrejtschuk6185
2 жыл бұрын
Hi, I have this issue on a BIxolon SRP-770III, I followed these steps but, isn't working. Is there any other option available to fix this problem on this printer? Thanks!
@thecollegepicker
2 жыл бұрын
That printer must not be the same programming language
@paulh909
3 жыл бұрын
My printer will not print now?? Says its in a error state
@ramonam4077
5 ай бұрын
Thank you we were able to fix it because UPS technical support was not of any help
@nycnftm
2 жыл бұрын
GREAT THANKS worked 4/20/2022 GX420t
@thecollegepicker
2 жыл бұрын
Thanks for letting us know 🙏🙏
@iScream1
2 жыл бұрын
HOW TO STOP HONETWELL PRINT BLANK LABELS, WHENEVER I TURN IT ON ? IT ALWAYS WASTE 7 BLANK STICKERS
@danacostello5908
Жыл бұрын
THANK YOU!!!!!!
@thecollegepicker
Жыл бұрын
You are welcome 🤠
@danacostello5908
Жыл бұрын
@@thecollegepicker I wasted so many damn labels. Lol
@nexus3d5
2 жыл бұрын
Nice vid. I wasted my time on three other vids/sites.. worked on my zp-450
@rayofbeauty2608
2 жыл бұрын
thanks
@kripsak
2 жыл бұрын
Zebra Legend!
@thecollegepicker
2 жыл бұрын
🙌🙌🙌
@adslusco
9 ай бұрын
Errr...this upset my Zebra ZD420. Any way i can reverse it?
@adslusco
9 ай бұрын
all good i clicked on reset printer....phew
@HenyTV
3 жыл бұрын
Hello, I have Zebra LP2844 and I have an issue with No Gap Detected during calibration. Do you know how I can fix this issue? Thank you
@thecollegepicker
3 жыл бұрын
What's up, are you using gapped paper? Continuous labels could throw that error.
@HenyTV
3 жыл бұрын
@@thecollegepicker Yeah I am using gapped label bought from ebay. Would you give me a link what you have ordered so I can compare?
@shittychannel4860
3 жыл бұрын
@@HenyTV Have it ever worked? try to clean the sensors with some 99% alcohol.
@HenyTV
3 жыл бұрын
@@shittychannel4860 I am about to try. Thank you for advice!
@HenyTV
3 жыл бұрын
@@shittychannel4860 this still didn’t fix the issue...
@sdhute
Жыл бұрын
How about on a Mac??
@GarageSaleMonster
Жыл бұрын
my Z is printing 21 labels and then stopping! i have to reboot cancel and then start at 22 and print again and it prints 21 more and then stops. driving me crazy
@thecollegepicker
Жыл бұрын
Oh no, it may be the max memory on your model for high batches.
@GarageSaleMonster
Жыл бұрын
@@thecollegepicker only 60 to 70 labels and the same z beside it is fine same printing. I have 4 of these beasts
@Benakuzo2
11 ай бұрын
I’ve been wanting to get a label printer for my small business for the longest time and finally pulled the trigger. I’m glad I did ! This machine is great kzitem.infoUgkxw55tQTywUAAOsbrlwxONZULry77sFF1Q and the blue/green color matches the rest of the accents in my office. My favorite part is how small the footprint is. It’s less than 1/4 the size of my regular printer.Set up was fairly easy. Seller will email you a link with video instructions Which I found to be more helpful than the written instructions. I use a Mac and had no issues. They even included an adaptor for USB to USB-c which is great because I’m always losing mine! I had a few issues getting the labels to print properly and wasted quite a few sheets. You need to play around with the settings to get everything adjusted just right. If you have the wrong settings, it’ll crop off the edges or feed through blank labels. These aren’t issues with the machine though, just user error.
@masterchief8855
3 жыл бұрын
Good stuff #printerpeople #droppingknowledgeandsavinglabels
@margaretoriley9793
4 ай бұрын
Sorry to say but my Zebra GK420D is still printing an extra label
@mlock5354
8 ай бұрын
If it is an ethernet printer just go to webpanel/View and Modify Printer Settings/Calibration/Head close->No motion
@urasphoumy
2 жыл бұрын
Our zebra will print the same sets of labels three times even though we only print once. We can’t clear printer queue
Пікірлер: 141