Hey Curt, Hope all is well with you and your family. I spent some time last night and replayed all your videos on the rebuilding of the L28 engine for your 240Z. I had forgotten how great those videos were - so helpful and informative. You had made a comment that you may not go into that level of detail on the 260Z build, but I hope you reconsider! Your videos are some of the best I've seen on rebuilding these motors and I personally can't get enough of the details. Just wanted to say thanks and send healthy well wishes to you and your family.
@CarsBikesandCoffee
4 жыл бұрын
+Mike Gadoury aw man thanks! I really appreciate it. Consider it reconsidered and I’ll do detail! My only concern was sounding like a college professor lol.hope you and you’re family are doing well in all of this too!
@justinwallen2911
3 жыл бұрын
Sweet video that buzzing when you open the door I took mine off it's in the middle console behind the radio it looks like a square plugged into like a three-pin harness
@CarsBikesandCoffee
3 жыл бұрын
Thanks! That’s awesome info, I appreciate it! 🤘🏻🔥
@markmarktv8781
4 жыл бұрын
Patiently waiting for episode 2
@CarsBikesandCoffee
4 жыл бұрын
+Jacob Johnson 🤘🏻
@ims5050
3 жыл бұрын
I just bought the same car! I'm in love! Bought it for 1100. New tyranny, clutch, slave cylinder, flywheel, gaskets and everything is pristine.
@CarsBikesandCoffee
3 жыл бұрын
Right on, congrats!! Sounds like you are set. Enjoy it!🤘🏻🔥
@noahtroxtel3643
3 жыл бұрын
some guys giving me his it was his first car for 1200 and it needs a battery and plugs and needs some cleaning and a paint job and hood thing is no rust i’m so excited to get this
@noley1650
Жыл бұрын
I’m hopefully going to buy a SL tomorrow for 2000 only issue is the clutch saving this video for later
@gymz4065
4 жыл бұрын
Welcome back bro! It’s been awhile! I hope the Z’s are doing well. The 3000GT is a beast!
@CarsBikesandCoffee
4 жыл бұрын
Thanks man!! Good to be getting back! Trying to fit in some quick builds to help the Z’s. Which I’ll be getting to soon.
@gymz4065
4 жыл бұрын
Cars, Bikes, and Coffee awesome we can’t wait to watch it!
@DadbrosGarage
4 жыл бұрын
Stm sells a hydraulic line that goes directly from the slave to the master cylinder really helped me out
@CarsBikesandCoffee
4 жыл бұрын
+Kens Garage I’ll have to check it out! Appreciate it!
@oemplus3613
4 жыл бұрын
Nice 3000gt
@CarsBikesandCoffee
4 жыл бұрын
🤘🏻thanks!
4 жыл бұрын
Many yrs ago I did exactly the same jobs on my 3000GT off camera. Bleeding and removing the slave cylinder were troublesome.
@DadbrosGarage
4 жыл бұрын
Nice car!!
@CarsBikesandCoffee
4 жыл бұрын
+Kens Garage Thanks!
@cameronarmijo4524
3 жыл бұрын
I gotta 1992 gt sl rattle in nutreul stops when clutch is to the floor is that tob or pilot?
@CarsBikesandCoffee
3 жыл бұрын
I’m willing to bet it’s the throw out bearing. Is there any play in the clutch fork?
@WILFRED1184
3 жыл бұрын
3k doesn't have a pilot bearing. Could be throw out or a warped clutch plate. I had an issue with mine where the throw out bearing went out and ate the fingers off of the pressure plate. It would rattle in neutral but it also squealed like crazy with the clutch depressed.
Пікірлер: 23