"The reason is far worse than anyone wants." That's the truth. The engine is worn. Can't make everyone happy with your evidence, you know. Great job.
@INSIDEHOUSEGARAGE
5 жыл бұрын
Thats what I thought too. Everyone is entitled to their opinions tho.
@congerscott6064
4 жыл бұрын
Anything can be fixed, it depends on how much time and money you are willing to put into it, in this case i would buy a new trimmer, thanks for the video 👍.
@INSIDEHOUSEGARAGE
4 жыл бұрын
You are absolutely correct. Thank you for the comment I appreciate it
@ScottJ5860
2 жыл бұрын
I couldn't tell you if it was savable. The damage on the piston would lead me to say no, and since it's been over 2 years, I'm guessing it doesn't matter anymore. With that said, this is the 5th video I've come across for this trimmer and probably the most informative. Greatly appreciated.
@INSIDEHOUSEGARAGE
2 жыл бұрын
no problem and you are correct, I haven't rebuilt it yet, because find the parts for an older trimmer is very difficult
@daviddettmers6616
2 жыл бұрын
I have this same trimmer and I'm having starting issues. Thank you for the very well put together video!
@INSIDEHOUSEGARAGE
2 жыл бұрын
Glad it helped!
@dougankrum3328
4 жыл бұрын
I recently inherited a used 2006 Husqvarna 125L 28cc string trimmer from my late brother....I have no idea of who, what, when, why, or where it was worked on....but it had 95 PSI, good spark and enough fuel going through to get the sparkplug wet....but, not even a 'pop' out of it....so, after many hours..... I removed the muffler, and piston/cylinder looked OK.....so I take it apart, a small damaged area on piston and cylinder (not enough to cause a big problem)...I ended up taking the engine completely apart and after much head-scratching....I found that the cheap-o cast aluminum flywheel was out of time on the crank, it was worked on by someone who had completely destroyed the 'taper' and 'cast-in' key in the flywheel where it tightens on the crankshaft.....I replaced the flywheel, cyl/piston with genuine Husqvarna parts...now has 130 PSI and runs great...the previous Piston/cylinder and flywheel were Not Husqvarna parts....and wads of black RTV all around the 2 case halves, where there was an obvious groove for a rubber type gasket. This is a good example of why you should just use the genuine parts...e-bay, I found NEW Husqvarna cyl/piston assy for $22...flywheel for $31...and $5.99 shipping.... At these kind of prices for New genuine parts...is it worth buying the cheap stuff?? The $$ 22.00 cylinder 'kit' included the piston/ring, nice rubber seals that go between case halves, and the 2 new crank seals... I'm 72 and have been doing Industrial mech/electrical/electronic maintenance most of my adult life....buying the 'cheap-o' replacements, has caused me endless nightmares like this....if you buy the cheap-o parts...it might run, but not for long....by the time you buy the cheap-o parts, and then later the 'new-original' parts, and the labor to install them...now you've spent more $$ that a brand new piece of equipment.... I hope this helps someone...!
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thank you for sharing your experience. I greatly appreciate it. Yes it usually not worth buy the cheapest sometimes.
@dougankrum3328
4 жыл бұрын
@@INSIDEHOUSEGARAGE Yes, the stuff I worked on was BIG and Very Expensive...no room for error....
@INSIDEHOUSEGARAGE
4 жыл бұрын
@@dougankrum3328 now I understand.
@ronmorris6563
2 жыл бұрын
I just fixed mine started by replacing the carburetor but that was not it. For those reading the comments, check the .070 x 1.864 o-ring located on the crankshaft endcap. If it is broke there is no vacuum to pull in the fuel. Good luck!
@INSIDEHOUSEGARAGE
2 жыл бұрын
Thanks for the info
@smashed-thumb9886
4 жыл бұрын
Thanks for the video, I have the same trimmer and every year multiple problems come with using it. I hope you have better luck with it being a parts trimmer.
@INSIDEHOUSEGARAGE
4 жыл бұрын
I appreciate that. Thanks
@js_1995x
4 жыл бұрын
I got one. Out the dumpster ran. Needed adjustment. Put a carb from my Murray because it was a new carb. Had to pour some gas down the throat to start it. Ran like a champ. Got hot, started bogging when I squeezed the trigger. Well I adjusted the hi, no difference. Stopped running. Poured some oil in the tank. Won't start unless I pour gas down the throat but it smokes.
@INSIDEHOUSEGARAGE
4 жыл бұрын
Remove the spark plug and look if the tip is black with burnt oil. Next Check the compression. Make sure it's not low. Your rings might be worn out making it hard to start.
@js_1995x
4 жыл бұрын
I saw oil running off the top of the cylinder. I tried taking the plug out but the threads are stripped so it won't come out
@INSIDEHOUSEGARAGE
4 жыл бұрын
@@js_1995x did you check the oil level? It might be overfilled
@js_1995x
4 жыл бұрын
@@INSIDEHOUSEGARAGE it's 2 cycle
@INSIDEHOUSEGARAGE
4 жыл бұрын
Gotcha. Is the pull rope easy to pull?
@PilotViewProductions
3 жыл бұрын
It's just 'me', but I'd buy the piston and ring off eBay and do the repair...but then again, you and I both have some degree of experience and are not afraid to tear em' down. My philosophy is: if it's already broken, how can I hurt it by trying to fix it. Plus, there are used pistons and rings on eBay for $4.99 if you wanted to roll the dice and go that direction. That Troy Bilt is nice and worth some degree of $$ to save it IMHO.
@INSIDEHOUSEGARAGE
3 жыл бұрын
You're absolutely right. I think I still have this somewhere so I might dig it up and try replacing the piston and ring. Thank you Pilot View Productions.
@bradrolling8637
3 жыл бұрын
I'm working on 25cc craftsman and it will try to start and run for about two or three seconds and then die . I've checked the piston and rings and they have scoring, but not quite as bad as your piston. I'm done with it, the owner says he never ran it with straight gas , but you know how that goes. Thnx for the video, now I can move on to a snapper s31sst that has super compression and will be an easy fix
@INSIDEHOUSEGARAGE
3 жыл бұрын
thank you Brad Rolling.
@blazuma111
2 ай бұрын
Yep, that piston was severely scored and completely beyond repair. This is usually caused by either making the fuel mixture way to lean by the carburetor adjustments, or using the wrong type of oil and fuel ratio like you said, most of the time. I hope this never happens to me lol. We can't save all of them sadly ):
@INSIDEHOUSEGARAGE
2 ай бұрын
you are correct, it's a shame really
@rockevronv11
4 жыл бұрын
I work on small engines like this and I had a Murray that did this except it would start on every pull but instantly die, I never figured out the cause, I believe it needed a new carb or a rebuild
@INSIDEHOUSEGARAGE
4 жыл бұрын
I believe you are correct. Thanks for the comment I appreciate it
@samuelvelez1643
4 жыл бұрын
I got a Craftsman trimmer just like the one featured on the video,I had a rough time trying to start it until one day I decided to check out the compression,so I took the muffler out and surprisingly the Piston is in good condition but noted that the muffler bolts were lose... After placing the muffler and tightened up the screws I did a little test...it did have a better compression,added the fuel mixture and Voila... It did started the way it should be, with plenty of power... In conclusion: check for loose screws in the muffler if in doubt
@billhendrickson5506
Жыл бұрын
I just tossed two trimmers with same problem. Low on compression generally indicts why no start. And the cost to repair, IF you can get the parts and do it yourself is the next factor to consider.
@INSIDEHOUSEGARAGE
Жыл бұрын
you are correct this one is not worth fixing it.
@Titan-mq6vy
2 жыл бұрын
Mine won’t restart after it’s been running for a while. I’m not sure what’s wrong with it and that’s how I came across this video. Thanks for putting it out there
@INSIDEHOUSEGARAGE
2 жыл бұрын
thank you Titan Destroy.
@omadathmarajh6643
3 жыл бұрын
I think is dependent on the condition of the cylinder that could determine whether its re useable ,
@INSIDEHOUSEGARAGE
3 жыл бұрын
You are absolutely correct. I haven't taken it apart yet so I'll see then
@Ayaz_Qais
4 жыл бұрын
Thanks, I was going to buy one of those but watching this video, one need to be a good mechanic to fix it. Therefore I order battery operated one. I hope it impresses me.
@INSIDEHOUSEGARAGE
4 жыл бұрын
I believe it will. Thanks for the comment I appreciate it
@samwdavis
11 ай бұрын
Reading the title, I already knew that it was a compression problem. This is VERY Simple.... there's fuel, there's spark... there is only one more element that we lack.... compression. PERIOD. This is simple logic.
@cdos9186
5 жыл бұрын
I don't know about you but if I got a trimmer with really bad engine damage I would try to get it to at least run. I would try to unseize the rings if the rings were stuck to the piston and I am curious to see if it would run again, but if the rings were not seized to the piston and they were how they should be and it still wouldn't run I would probably put it up as a decoration in my garage rather than throwing the engine away.
@INSIDEHOUSEGARAGE
5 жыл бұрын
Now that's an idea. Sorta like a trophy.
@bradrolling8637
3 жыл бұрын
A reminder not to go cheap on your lawn equipment
@cdos9186
3 жыл бұрын
@@bradrolling8637 Not in the way you're thinking. Buy quality used, not cheap new.
@gimmesomesugar
2 жыл бұрын
I love these trimmers. I've had very good service out of them. I use canned fuel with all the goodies in it and run mine mostly at full throttle. poor maintenance and misuse will ruin anything! Good video.
@INSIDEHOUSEGARAGE
2 жыл бұрын
thank you James
@stevieg.4816
4 жыл бұрын
You can buy a complete used engine for $25.00 or new one for $79 on ebay. A new trimmer is $179.00 at Lowes for one. I would either buy a new trimmer or if I had the time and felt like it save money and replace the engine they bolt right up. If I went new I'd buy a four stroke.
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thank you Steve Guillete for the comment I appreciate it
@jonienglish3231
5 жыл бұрын
I had a Poulan blower did not start , low compression Rings Seized onto piston after putting a new Rings ran like a Champ
@INSIDEHOUSEGARAGE
5 жыл бұрын
Glad you got it working again. Thanks for the comment I appreciate it
@tresben6758
4 жыл бұрын
It all depends on the condition of the cylinder house cause you can get some pretty cheap universal piston and ring kits from China on the internet these days. Not the best solution I know but if it gets you up and running again... Also I've seen universal cylinder houses online from as little as £10, I'm doing a rebuild myself on a Trimmer at the moment but decided to go OEM as the trimmers pretty new and was given to me for free so I thought why not.
@INSIDEHOUSEGARAGE
4 жыл бұрын
I understand. I would probably go the same way as you on the repair. Thanks for the comment I appreciate it
@Matt-wl3jo
4 жыл бұрын
Check the spark arrestor, because some times those will gum up. Also check that electric starter in the back. Those gum up sometimes
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thanks for the comment I appreciate it
@johnsteed265
4 жыл бұрын
Thanks for the great video with clear and excellent information! I would not have thought to look in that spot for damage to the piston. Why do you care what others comment when you know you are right? A Troybilt trimmer costs about $125 or so. If I had that unit and it had no compression I would not think twice about tossing it (or saving it for parts like you do). Rebuilding the engine would be too time consuming and the parts and time would probably cost as much as a new trimmer. Thanks again for the valuable information!
@INSIDEHOUSEGARAGE
4 жыл бұрын
you are correct about other people's comment . they would like to see the rebuild and how involved it is then i think they would just replace it instead
@johndeane141
4 жыл бұрын
once the piston and cylinder are badly scored,You will need a cylinder and piston kit,make sure correct oil fuel ratio,and clean air filter
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thank you John Deane for the comment I appreciate it and you absolutely correct
@dougankrum3328
4 жыл бұрын
That piston looks pretty bad....I have friends who sell and service NEW 2 stroke power tools, the damage here can often be caused (usually on chain-saws) by 'lean-seize' failure...guys crank that high speed jet in until it's just screaming fast...then after a minute or 2....all comes to a halt..... Their usual comment after asking what happened....."I don't know...it was cutting like the devil, then just stopped"..... You just gotta' bear in mind, the amount of oil going through the engine is miniscule.....
@INSIDEHOUSEGARAGE
4 жыл бұрын
@@dougankrum3328 yes you're right this was a lean condition that caused this.
@free2binnh
2 жыл бұрын
I have the exact same weed Wacker as in the video. It starts runs rough, seems to be skipping a lot and then dies. When it did start, would choke when throttle was pressed and roar. I always used the premixed gasoline, TruFuel 40:1 mix, was suppose to be the right mix, but I think the mix should have been 30:1 or 20:1. I was told the 40:1 was the right mix. I am not taking it apart, it's headed for the dumpster. I bought a 17 inch Dewalt 60v string trimmer that will accept Trimmer Plus tools. Came with a 9AH battery and charger. No oil, no gas and no hassle needed or necessary to get the trimmer working. The Trimmer Plus tools are looking pretty lame, so might buy the Dewalt attachments in the Spring. I suspect the cylinder is scored also. In any event I am done with Troy-Bilt stuff. Battery powered tools is the way to go. No pollution created with battery driven tools.
@INSIDEHOUSEGARAGE
2 жыл бұрын
yes and maybe, if you have a small yard they will work, but if you need more time, the batteries will have less capacity after every season. So just buy another $100 battery then? that's a lot of money.
@rudyferrell
2 жыл бұрын
I went with a Dewalt electric weed eater also. Weed eater engines are a pain
@victoryfirst2878
4 жыл бұрын
The unit is just junk. The previous owner did not use any oil in the mix. I repair weed eater all the time and most owners will swear by their mothers grave they took great care of the unit. But low compression means the owner lied. What you have showed is just right on. I still do not know why people want to lie. But the weed eater will tell no lies, just as dead men tell no tales. Nice video with the facts. Good Day Too. VF
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thanks and I totally agree with you
@massimoterenzi5056
3 жыл бұрын
I can see a commercial unit such as Echo,Shtil,ect,being worth saving, residential equipment such as this not so much. However if this unit only required a carb rebuild or something minor then yes its definitely worth investing a little time and the fix is not that expensive. Love your videos keep em comin!!!
@INSIDEHOUSEGARAGE
3 жыл бұрын
I completely agree with you.
@winstonclarke9221
3 жыл бұрын
Depends on the cost for parts, then you can fix it, if its too costly then don't.do it.
@INSIDEHOUSEGARAGE
3 жыл бұрын
That makes sense
@lewiemcneely9143
2 жыл бұрын
Needs some new parts just like my saw did when I got it. Thanks and Blessings!
@INSIDEHOUSEGARAGE
2 жыл бұрын
no problem Lewie McNeely
@adamohsberg960
2 жыл бұрын
My trimmer just like the one in this video won’t start. I have the proper mix of oil and gas. One day while running my trimmer it just stopped and wouldn’t start again. I just replaced the spark plug with the recommended plug and gap. After watching your video - I bought the tools from your affiliate links: Compression Tester (after 3 pulls it went to 90 psi), spark inline tester -(bulb flashes when cord is pulled), and adjustment tools. The tension on the cord isn’t great but there is some. The carb screen looks clean, and when I press on it fuel goes through. So I don’t think the carb is bad. I tried pouring a little mix down the carb throat. I got the drill bit tool as well to try and use my drill on high speed to start it and it won’t go. I haven’t looked at the piston yet because the compression was high. Any ideas? Great video by the way and thanks
@INSIDEHOUSEGARAGE
2 жыл бұрын
thanks for choosing the links, I didn't catch it, but did it run, when you put mixed fuel in the carb, and tried starting it? Also, next time, when you try and start it, Try not to choke it, and us the drill, after a few seconds, then try and choke, it. IF it doesn't start, then replace the carb.
@tonygaytan9848
4 жыл бұрын
Thank you, for your time.
@INSIDEHOUSEGARAGE
4 жыл бұрын
No problem
@robeftyearian8760
5 жыл бұрын
I thinknits a fuel issue and carbon messed up the piston and rings won't know if it's salvageable till broke down
@INSIDEHOUSEGARAGE
5 жыл бұрын
Yes its was definitely a fuel issue. Thanks for the comment.
@Patrick4959
4 жыл бұрын
always remember to keep your eyes out for a cylinder kit there maybe one out there you never know and i have seen them at good prices online like Forctec
@INSIDEHOUSEGARAGE
4 жыл бұрын
I absolutely will
@Patrick4959
4 жыл бұрын
@@INSIDEHOUSEGARAGE my pleasure mate and cheers from Australia
@Marty1959
3 жыл бұрын
I wouldnt even bother to fix it find a good decent echo they are reliable and tough
@INSIDEHOUSEGARAGE
3 жыл бұрын
you are absolutely right about that.
@localhandyman8975
3 жыл бұрын
Hey, a friend just gave me his TB trimmer b/c he says it won't run... fuel goes through the bulb & into the tank just fine; however, it won't start, even by putting fuel directly into the carb'...I grounded the plug to the block & No Spark!?! How can I tell if my challenge is the ignition module OR Stop switch??
@INSIDEHOUSEGARAGE
3 жыл бұрын
sure, you can try and take the handle apart and disconnect the wires on the kill switch and try the test again. if you still don't have any spark then you can remove the ignition module and clean any rust on the part that makes contact with the engine and reinstall it and test it again.
@amelikanovic2185
3 жыл бұрын
I hawe a Brast trimmer. It starts (100 pulls to start) but it is hard to pull the string. But when i start it everithing is ok but starting is reali hard. What can i do?
@INSIDEHOUSEGARAGE
3 жыл бұрын
Easiest thing would be to replace the carb.
@rhyswood9151
Жыл бұрын
It's fixable but would be a whole cylinder and piston rebuild which is only really worth doing as a hobby as it takes too much labour and parts. Customers are better off buying a new one normally
@INSIDEHOUSEGARAGE
Жыл бұрын
you are correct the price for the parts is pretty amazing.
@jamesfazackerley7757
6 ай бұрын
I had a chainsaw with the same problem the piston was damaged but the cylinder just needed a clean,,as good as new damaged by cheep 2t oil
@INSIDEHOUSEGARAGE
6 ай бұрын
yes unfortunately a decent oil will keep that from happening
@JasonSmith-qx3zh
3 ай бұрын
Not for the long run, it's got to be rebuilt for that to happen.
@INSIDEHOUSEGARAGE
3 ай бұрын
thank you
@alanlake5220
4 жыл бұрын
It all depends on the cost of a new piston and cylinder, if not way too much yes i would fix it and get a few more years life out of the trimmer
@INSIDEHOUSEGARAGE
4 жыл бұрын
Excellent answer. Thanks for the comment I appreciate it
@leahg3056
4 жыл бұрын
Can someone explain what exactly we're looking at inside that is bad? Is it the blackening? Chipping of the metal? I don't have much experience with engines but I'm having a similar issue with mine and I wanted to check this out! Mine stopped starting well after a bad accidental knock on a fence post that killed the engine. It's been hard to start since.
@INSIDEHOUSEGARAGE
4 жыл бұрын
the main reason why this trimmer died is that the oil gas mix was not correct. The result was a scored piston which reduces the engine ability to compress the air and fuel mix. You can see the scoring after I take off the muffler and the vertical lines on the piston and ring which shouldn't be there.
@leahg3056
4 жыл бұрын
@@INSIDEHOUSEGARAGE thank you so much!!
@INSIDEHOUSEGARAGE
4 жыл бұрын
@@leahg3056 no problem
@anthonymiddleton4590
4 жыл бұрын
that trimmer is definitely fixable, just needs some new ring ( and maybe a new piston while you're at it) clean out the carb and you should be good to go... looks like it ran on raw gasoline
@INSIDEHOUSEGARAGE
4 жыл бұрын
I believe you're right. Thanks for the comment I appreciate it
@bradrolling8637
3 жыл бұрын
It's not feasible, just add $150 to the price of a new one of those cheap and get a mid grade echo, stihl or husqvarna and your problem is solved
@boydlittou9446
Жыл бұрын
The crankcase end cap had loose screws on mine and wouldnt let it push fuel to the cylinder. I cant believe how cheap and sorry the tolerances are on the end cap also. It fits sloppy and only has a skinny o-ring to seal it. Nothing to center it good except the 2 small screws. Wont buy another one of this brand.
@INSIDEHOUSEGARAGE
Жыл бұрын
it happens
@RussellBooth1977
4 жыл бұрын
No,at least the top end is screwed so the engine will at least needed a cylinder & piston rebuild kit fitted if it's worth it !
@INSIDEHOUSEGARAGE
4 жыл бұрын
You are correct. I don't think it's worth it on this particular trimmer.
@rogerpattube
2 жыл бұрын
Troy bilt say to hang it vertically, trimmer end down.
@tazmun
3 жыл бұрын
Personally I’ve had great results with Chinese cheap reproductions parts vs OEM. Your experience may vary. But if I can rebuild with a cylinder piston kit for under $30 on eBay I’m tempted to roll the dice.
@rrmackay
Жыл бұрын
I would say not savable without new piston and ring, 2 cycle rebuilds are pretty cheap but I am guessing from the damage that the cylinder i probably toast as well. its garbage.
@INSIDEHOUSEGARAGE
Жыл бұрын
you are correct the parts are hard to find.
@philg4116
27 күн бұрын
Is the phrase "hard to start" still in the lexicon? Doesn't appear so on youtube.
@INSIDEHOUSEGARAGE
27 күн бұрын
no not ever
@wesleyhoehn9423
4 жыл бұрын
Turn the low and high idle screws
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thank you for the comment I appreciate it
@wesleyhoehn9423
4 жыл бұрын
Thank you for responding
@gregrichard9192
3 жыл бұрын
At that stage imo it's best not to repair, get a new one
@pyrog.c.c89
4 жыл бұрын
Good job buddy.You found the problem.
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thank you for the comment I appreciate it
@dougdepaul883
4 жыл бұрын
I have the same problem with one I'm working on. I got 60 lbs compression. Now I've seen some start with low compression. This particular one I can't get anything out of it. Does putting oil in the cylinder raise the compression when testing it ? Thanks.
@INSIDEHOUSEGARAGE
4 жыл бұрын
Yes it can bump the compression up enough to help start it.
@clifforddurrance8234
5 жыл бұрын
Out of mistake I picked up my 4 cycle gas instead of t2 cycle I buy in the can, it ran for awhile but quit on me. Then I figured out my big mistake. My weedeatter still has compression, its has resistance when I pull the rope. Is it still fixable?
@INSIDEHOUSEGARAGE
5 жыл бұрын
Thank you for the comment. If you can install a compression tester in your weedeater it would show just how much compression it has. If it's over 55 psi then its useable. If it's under 50 then theres not much that can be done.
@js_1995x
4 жыл бұрын
Yes there are 2 screws holding the cylinder on the bottom when the tank is removed
@beterwithab
Жыл бұрын
1:57 is it normal for the throttle switch on the carb to go full throttle when you engage the choke, because my trimmer does that
@INSIDEHOUSEGARAGE
Жыл бұрын
from what I've seen, on autochoke style carbs, when the choke is active, the carb will go to "hi" idle.
@peterpitocchi9554
Жыл бұрын
My cousin gave me the same trimmer-same problem scored piston. Tock it apart and found a broken ring, which also took a small chunk out of the side of the piston, cylinder also scored. I installed a “short block” which included crankcase, piston and cylinder head. I could not find a replacement piston, just as well cuz cylinder scored too. Cost about $60 delivered. Repair was successful. I wonder if these engines commonly break rings. Anyone know?
@INSIDEHOUSEGARAGE
Жыл бұрын
nice work, not that I know of, the person who I got this from always ran their oil mixture, "thinner" than they should have
@jws3925
Жыл бұрын
Had two. Both did the same even though it had the same oil/gas mixture used in my other 2 cycle equipment. I think these are junk
@t-techvids9659
3 жыл бұрын
What if my engines starts but then it dies out 2-3 secs after. You think it's the carb issue?
@INSIDEHOUSEGARAGE
3 жыл бұрын
without any other information, yes I think it's a carb/fuel system issue.
@t-techvids9659
3 жыл бұрын
@@INSIDEHOUSEGARAGE thanks for the quick response. I did order a carb replacement on eBay. Hope it will fix the issue.
@INSIDEHOUSEGARAGE
3 жыл бұрын
@@t-techvids9659 no problem. When you look at the carb make sure the fuel lines and fuel filter are in good working order
@2035jim
2 жыл бұрын
The problem is compression but I don’t think you need a full rebuild I would put lubricating oil in the cylinder and the rings will grab better and it should give you a few years
@INSIDEHOUSEGARAGE
2 жыл бұрын
I have done that before, but wouldn't have to do that every time I wanted to start it?
@2035jim
2 жыл бұрын
@@INSIDEHOUSEGARAGE you would probably have to do it every month if you use it weekly
@tttttttt8482
Жыл бұрын
What kind of oil to put in, and how much, could you explain, please?
@2035jim
Жыл бұрын
@@tttttttt8482 you would just use Marvel mystery oil but you wouldn’t put much in just a couple drops and it should start right up
@gmazjunior162
4 жыл бұрын
I don't know but my trimmer is nkt good because I opened carb a few times and nothing happend I saw my piston and it's fine and it still doesn't start
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thank you for the comment. Did you try a compression test? Even with a good looking piston the number might be low enough for it to not start.
@uberdimensionalebrottute4354
5 жыл бұрын
How much PSI needs an engine to start properly?
@INSIDEHOUSEGARAGE
5 жыл бұрын
Ideal probably 90 but I never test freshly broken engines. Anything over 70 should start normally.
@samuelvelez1643
4 жыл бұрын
Depending on how much cost a new Piston and the cylinder itself
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thank you for the comment I appreciate it.
@UTube_userRM
2 жыл бұрын
About that compression tester that you listed from your tool bag....is that the actual tester you use? I see a few reviews for that product that it may be more appropriate for a car rather than the small engines. Is that really the tester you use and does it work well for you for small engines like weed eaters? Thank you for your videos.
@INSIDEHOUSEGARAGE
2 жыл бұрын
If I recall, I think it's from the same but they may have switched to a different supplier. Personally I don't see a real difference between the one for small engines, or one for an automobile
@delincejoint7129
4 жыл бұрын
What can of gas the trimmer used
@INSIDEHOUSEGARAGE
4 жыл бұрын
the fuel it was using was thin on oil.
@jgarcia238ify
5 жыл бұрын
Hello Sir my troybuilt starts but shuts down when goes to idle. Then after that it wont turn back on at all. Has a good working carb and gas is not old either please advise and thanks!
@INSIDEHOUSEGARAGE
5 жыл бұрын
The easiest thing would be to have the carb adjusted and after that is to replace the carb completely. When was it working properly last?
@jgarcia238ify
5 жыл бұрын
@@INSIDEHOUSEGARAGE its brand new now just installed it but it worked intermittently with the old carb but I couldn't get it adjust at all so I bought a replacement carb
@INSIDEHOUSEGARAGE
5 жыл бұрын
@@jgarcia238ify without seeing in person this will be difficult. You might have to have a professional look at it.
@jgarcia238ify
5 жыл бұрын
@@INSIDEHOUSEGARAGE okay thanks!
@cdos9186
5 жыл бұрын
So the people that owned it didn't put enough oil in the gas?
@INSIDEHOUSEGARAGE
5 жыл бұрын
Yes after talking to them they confirmed that they were eyeballing the mixture last year it was being used and it was admittedly light on oil.
@johnwayne6927
4 жыл бұрын
Troy built trimmer runs funny
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thanks John Wayne.
@stevehertz4878
4 жыл бұрын
Fix it and c how it turns out ..if good then u win.
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thank you Steve Hertz for the comment I appreciate it.
@williamwatkins7145
11 ай бұрын
Correct 👍
@nicolabooth6075
4 жыл бұрын
I would get an aftermarket piston and cylinder and piston ring /rings and rebuild it
@INSIDEHOUSEGARAGE
4 жыл бұрын
Excellent choice. Thanks for the comment I appreciate it
@ianvaldivia1993
4 жыл бұрын
By the time you buy the piston cylinder and rings you might as well not waiste your time and buy a new one because its abou the same price
@INSIDEHOUSEGARAGE
4 жыл бұрын
@@ianvaldivia1993 you are absolutely correct. Thanks for the comment I appreciate it
@roadstar499
4 жыл бұрын
so to fix this correctly what parts would be needed... piston,ring? what about cylider? thanks
@INSIDEHOUSEGARAGE
4 жыл бұрын
Yes basically a top end kit.
@ramadinsookhoo6141
3 жыл бұрын
Can a trimmer with a curved shaft be switched to a straight shaft and will it perform the same or better with different shafts?
@INSIDEHOUSEGARAGE
3 жыл бұрын
yes they can be switched but the process is very involved. in Fact thats the video I'm releasing soon. Performance wise, I couldn't say.
@CuriousKL
2 жыл бұрын
This is the 'exact' same unit my neighbors has with the exact same issue.
@INSIDEHOUSEGARAGE
2 жыл бұрын
that's a shame, this one won't run without a rebuild.
@danoakley6538
3 жыл бұрын
Some require 40-1 and some require 50-1. Why not just one for all engines?
@INSIDEHOUSEGARAGE
3 жыл бұрын
its's up to the manufacturer to decide. I usually see 40:1 on low end machines while those that require 50: are much more expensive. I would assume it's related to what kind of bearings they use inside the engine . I just use 40: on every 2cycle unless its one from a long time ago. some of those require 32 or even 24 to 1 mix.
@robertfaber1346
Жыл бұрын
I have a toro 4cykle that's getting fuel and spark but seems like no compression
@INSIDEHOUSEGARAGE
Жыл бұрын
have you checked the valve lash?
@robertfaber1346
Жыл бұрын
@@INSIDEHOUSEGARAGE not really but I'm told that they may need adjusted so I'll ask how and what guage To use
@robertfaber1346
Жыл бұрын
Also it's blowing oil out the emissions filter I've replaced coil for said 4 cycle weed eater and cleaned carb still no start
@INSIDEHOUSEGARAGE
Жыл бұрын
these engines don't need a lot of oil, maybe pour it out and put whatever the amount the owners manual States.
@brucecoleman7412
Жыл бұрын
Unfortunately, the cost of repair could easily exceed the value of the trimmer. Even if you replaced the piston and cylinder, we still (at this point) no nothing about the carb, the crankshaft, or the cylinder head. I would buy a new one or at least a used one that runs.
@INSIDEHOUSEGARAGE
Жыл бұрын
you got that right, I would be fixing it for the experience I guess.
@lillianwhite9113
3 ай бұрын
WHAT TYPE OF OIL DO I ADD TO THE GAS/
@INSIDEHOUSEGARAGE
3 ай бұрын
synthetic 2 stroke oil
@KeganP04
5 жыл бұрын
one of the reasons the cord is easy to pull is because it has a ez pull starter
@INSIDEHOUSEGARAGE
5 жыл бұрын
Thank you for the comment I appreciate it
@KeganP04
5 жыл бұрын
@@INSIDEHOUSEGARAGE no problem
@4554dy
4 жыл бұрын
The engine was obviously run on straight gas. The cylinder must be toast as well. Not worth the rebuild IMO.
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thank you for the comment I appreciate it
@doraescalante1273
5 жыл бұрын
Ok those in Lowes * 😊* are a couple hundred dollars . I have one xp model at my home and it's sometimes bogs down 😞
@INSIDEHOUSEGARAGE
5 жыл бұрын
Yes this wasn't the cheapest one but it certainly has some issues.
@zone559
5 жыл бұрын
Where do you buy carb rebuild kit for cheap? Thanks
@INSIDEHOUSEGARAGE
5 жыл бұрын
You can get them on Ebay for cheap. I only buy the metering diaphragm however and not the whole kit.
@stevieg.4816
4 жыл бұрын
Ebay
@DougHinVA
4 жыл бұрын
at 3:30 I do not see any spark...
@INSIDEHOUSEGARAGE
4 жыл бұрын
It's at 3:22
@dougankrum3328
4 жыл бұрын
It's there, but hard to see....I just use the spark plug, short it to engine case (metal) and it's pretty easy to see....or you can just hold the sparkplug in your hand and you'll know pretty quick if I has spark....
@INSIDEHOUSEGARAGE
4 жыл бұрын
@@dougankrum3328 I appreciate your experience on the matter.
@mikemcmanus3918
2 жыл бұрын
Can you suggest a good weed trimmer?
@INSIDEHOUSEGARAGE
2 жыл бұрын
sure, anyone, you can afford, and take care of. It doesn't matter if you get a $100 or $300 trimmer, if you don't take care of it, it's going to develop problems. homelite straight shaft, or even blackmax is fine.
@alssmallengines
5 жыл бұрын
In my opinion it's not worth rebuilding. But that's just me. It's so easy to mix 2 cycle fuel properly I can't understand how people can screw that up...lol
@unisol2287
5 жыл бұрын
Careless, they don’t know how to handle this equipment, usaly they need to learn on the hard way
@INSIDEHOUSEGARAGE
5 жыл бұрын
They're just being lazy is all. That came from them too.
@bradleygower7181
4 жыл бұрын
Are you gonna rebuild it
@INSIDEHOUSEGARAGE
4 жыл бұрын
I'm thinking about it if I can find the kit
@bradleygower7181
4 жыл бұрын
Usually if I can’t find one I look for one that will fit and have around the same cc and it usually works.
@bradleygower7181
4 жыл бұрын
Usually if I can’t find one I look for one that will fit and have around the same cc and it usually works. Good luck.
@CarlosAmaya-nb6ps
4 жыл бұрын
I would just use it for parts.
@INSIDEHOUSEGARAGE
4 жыл бұрын
I may have to. Thank you Carlos Amaya for the comment I appreciate it
@tommyfox4444444
3 жыл бұрын
great video
@INSIDEHOUSEGARAGE
3 жыл бұрын
Thanks!
@LuminousSpace
4 жыл бұрын
i forgot the existence of that pump..... that is why it isnt start lol
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thank you for the comment I appreciate it
@aeson33
3 жыл бұрын
Troy built with blown engine. Parts only, no rebuild unless you find a Troy built fanboy.
@INSIDEHOUSEGARAGE
3 жыл бұрын
that makes perfect sense to me.
@legendarygamerlegend
Жыл бұрын
spend a while welding the piston and grinding it. heck, u cud even weld it and out it on a lathe instead of grinding.
@carlosavalos9937
4 жыл бұрын
That piston looks pretty bad might be better using it for parts
@INSIDEHOUSEGARAGE
4 жыл бұрын
Oh yes you are very correct. It's just a part machine now. Thanks for the comment I appreciate it
@Eli-hd5ph
15 күн бұрын
My weed will start but stay going
@INSIDEHOUSEGARAGE
15 күн бұрын
you mean, "it won't stay going"?
@PG_Mechanics
5 жыл бұрын
I don’t think it is worth fixing it. I would just buy a new trimmer unless it was expensive.
@INSIDEHOUSEGARAGE
5 жыл бұрын
It's a very cheap trimmer but I want to rebuild later in the year.
@timtoro244
2 жыл бұрын
Hello Home Garage soon it's my Birthday
@INSIDEHOUSEGARAGE
2 жыл бұрын
that's good to know
@Subzero9767-u2g
3 жыл бұрын
Not repairable
@INSIDEHOUSEGARAGE
3 жыл бұрын
thank you Moses Rodriguez
@pyrog.c.c89
4 жыл бұрын
👍👍👍👍👍
@INSIDEHOUSEGARAGE
4 жыл бұрын
Thank you for the thumbs up. I appreciate it.
@unisol2287
5 жыл бұрын
Use it for parts and buy a new one and avoid all kind of headaches
@INSIDEHOUSEGARAGE
5 жыл бұрын
You're right it is a headache.
@smitty9733
Жыл бұрын
I owned one of these and they aren't very well made . Two strokes in a string trimmers case are way better, IMHO
@INSIDEHOUSEGARAGE
Жыл бұрын
you are correct
@colesteffens5402
3 жыл бұрын
Junk, throw it out. It’s a Troy Bilt too which I personally don’t like
@INSIDEHOUSEGARAGE
3 жыл бұрын
I know how you feel. It's definitely not a stihl or echo
Пікірлер: 251